Ford Ranger / B-Series :: 1986 - Stalls / Idles Or Runs Roughly And Will Miss Erratically
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
Ford :: 1996 Ranger Idles Roughly, Stalls Out During Hot Weather
I recently purchased a 1996 Ford Ranger with the 4 cyl. engine. The first 10 days I owned it it ran just fine. I then took a an hour drive to another city. After the first few stops there, as the temperature outside reached about 90, It started to sputter and idle very badly. After I got rolling it would would run fine. I decided to try to make it home. It ran fine at freeway speeds of about 70 mph. I had to stop once; it stalled out and would not start again. After waiting about ten minutes I tried again. It was still running rough, but I was able to get rolling and drove the rest of the way home without any problems until I was in town and had difficulty keeping it running at idle.
The next morning it ran fine again. A local mechanic changed the fuel filter, but the problem came back as soon as the temp neared 90 degrees. A mechanic friend who witnessed the problem said that it definitely sounded like a lack of fuel and not an electrical problem. Is there a way to troubleshoot without swapping parts? If the fuel pump is failing in warm weather, how is it possible that it runs fine at 70 mph, but not at idle? Engine temp gauge looks good. I did get one code after it died the first time (lean mixture, I think he said).
Ford Ranger / B-Series :: 1986 - Stalls When Hot / Won't Restart Until Cool
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
Ford Ranger / B-Series :: 2003 4.0L Idles Fine But Stalls When Given Gas
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Ford Ranger / B-Series :: 1986 - No Fuel To Rail / Truck Quit On The Way
I have a 86 ranger 2.9 5 speed. A few days a go I replaced the front fuel filter and all seemed ok. Last night on my way home the truck quit and I had to have it towed home. Now I find both pumps don't seem to be working. What would make me loose both pumps??
View 11 RepliesFord Ranger / B-Series :: 1986 - Fuel System Wiring Diagrams?
Looking for the wiring diagrams for 86 ranger fuel system. I replaced the fuel pump relay after testing and finding that it was bad, still not getting fuel. I want to test any fusible links or anything else that could have gone wrong before I throw another part at it.
View 1 RepliesFord Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord Ranger / B-Series :: 1986 Just Cranks But Won't Start
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesChevrolet - Celebrity :: 1987 - Idles Roughly, Stalls When Gas Is Applied
I bought a 1987 Chevy Celebrity for $700.00. Initially it ran fine after just a slight hesitation when the accelerator was first pressed. With a little more gas applied it smoothed out and ran well. Yesterday I took a drive to the library. On the way the engine stalled. After a minute or so I was able to restart the engine and proceeded to the library. On the way home the engine again stalled. I was able to restart the engine but it idled roughly and stalled as soon as the accelerator was pressed even slightly. I tried varying the amount of gas applied from very little to pressing the pedal to the floor to rocking the gas pedal to no avail. So; idles roughly, stalls when gas is applied.
View 8 RepliesFord Ranger / B-Series :: 1991 - How To Time Idles High At Start
I now have a 1991 ranger 3.0 super cab. I need a step by step walkthrough of how to time it. Keep in mind that I ha the distributor out while turning the engine over so I need from start to finish, including the spout connector. It runs right now but idles high at the start and the. Stumbles down to about 500rpm and sometimes dies....
View 12 RepliesFord Ranger / B-Series :: 1999 - Lacking Power / Idles Erratically When First Start It In The Morning
ok so let me start by saying, my name is Tim, I own a 1999 Ford Ranger 6 cyl, 3.0L truck, I bought it brand new in 1999 and drove it for a few years and then took it off the road for 3-4 years then last year I went to put it back on the road and I couldn't get it running.
I took it to the dealer and they replaced a key switch module. since then the ranger seems to lack power. It also idles erratically when you first start it in the morning too.
not sure whats going on here but the engine light is on,
I get codes P0171 & P0174 (too lean bank 1 and too lean bank 2)
I would also like to note that I have replaced the fuel pump, fuel filter, transmission filter, MAF sensor, IAT sensor, PCV valve, EGR valve, TPS sensor, idle control solenoid, fuel pressure regulator & new plugs. I have also checked for vacuum leaks with no avail.
Ford Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: Transmission Start Jerking When Give It Gas / Engine Stalls
I have a 2000 ranger 4.0l 4x4 automatic transmission 5r55e. When I put it in drive I don't have any problems except in do it starts jerking when I give gas. When I put it in reverse I can move but as soon as I give gas it stalls the engine tranny was sitting in another truck swapped it with mine I changed the filter and 5 1/2 quart of oil.
I when to a transmission shop plugged it inn no codes and he said he would changes all solenoid and valve body gasket but he's not sure what is the problem. So I started to take out valve body and notice the oil is darkish red and was wondering if it was normal or not and if I'm taking that valve body out for nothing or should still go ahead ...
Ford Ranger / B-Series :: 2001 Edge Really Rough At Start Up / Stalls On Hard Acceleration
2001 Ranger Edge 3.0. Like the title says, when I start my ranger it idles really rough. If I give it gas it shudders like it's gonna die. After about 2-3 minutes it smooths out. If I'm on the interstate and down shift to pass someone, while accelerating it feels like I have a misfire (no CEL given) not all the time though. I've changed plugs and wires and it stopped doing it so I thought I had it but, it continued a few days later. Then I changed the fuel filter and it stopped again for a few days. Well it's back again. I'm thinking it's the fuel pump but I wanted to check here before I take my truck bed off. I also checked for vac leaks and I'm all good there.
View 1 RepliesFord F-150 - 1997-2003 :: 1999 - Timed Engine Now Hard Start - Idles Roughly?
I have a 1999 F150 4x4 5.4, I pulled the heads due to blown head gasket. Prior to pulling heads truck started and run fine other than miss on #1 cylinder. I timed the engine according to Haynes manual and posts on this site. Truck is now hard to start and idles very rough. I does seem to smooth out when reving the engine and seems to have plenty of power. Cant find any vacuum leaks or unplugged wires.
View 1 RepliesFord Ranger / B-Series :: 1986 - Engine Won't Firing
i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is
View 1 RepliesFord Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
Ford Ranger / B-Series :: 1986 - Bogs Down When Put Into Throttle
1986 Ranger 2.3 inline 4
I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.
Ford Ranger / B-Series :: 2007 - Idle Roughly In Park And Drive?
The trucks seems to Idle Rough in Park and Drive, Cold or Hot. It mellows out as soon as I give it gas but at stop lights or in park it goes back to a seemingly rough idle.
This is my first Ford Ranger and dont know if its normal. No code or dummy lights.
2007 2WD 4cyl