Ford Ranger / B-Series :: 1995 - Rough Idle And RPMs Drops?
1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 RepliesFord Ranger / B-Series :: 1999 - High Idle - ECM?
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
Ford Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: 1996 - Running Rough / Smooth Out A Bit When RPMs Raised Up
Recently bought a 96 4 cylinder 5speed 2wd ranger. 200xxx miles on it and its former owner had a young guy change spark plugs . Truck ran fine before, but after is when the rough running showed up.
A quick check of the plug wires and there locations looked correct and also tested the wires for spark with a timing light attached to them, checked shows all are firing.
Seems to smooth out a bit when rpm's are raised up, but still acts like not running smooth.
I swapped out plugs. Looks like they haven't been changed in a long time .Some of the straps are burnt and are shorter than they should be, but still runs rough, very little improvement .
Check vacuum lines for leaks/breaks and all looked good. removed line off brake booster and plugged, didn't matter.
It doesn't throw and check engine lights. It does smooth out some as the rpm's rise, but still not smooth .
Ford Ranger / B-Series :: 2004 - Hard Starting / Rough Idling / No RPMs
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesFord Ranger / B-Series :: Truck Idles With Very High RPMs When Driving And Shifting Gears
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesFord Ranger / B-Series :: Started Revving Real High (about 4000 RPMs) And Getting No Power (20 MPH)
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
Ford Ranger / B-Series :: 1998 - CEL Started Flashing / Idled Rough But More RPMs Smoothed Out
I have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 RepliesFord Ranger / B-Series :: Hissing Noises And Idle Fluctuate Between 2500 And 3000 RPMs
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
Ford Ranger / B-Series :: 1992 - Very High Idle At About 3500 RPM
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 RepliesFord Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: 1998 - Rough Idle At Cold?
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesFord Ranger / B-Series :: 1987 XLT - High Idle When Started For About 6 Minutes
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 RepliesFord Ranger / B-Series :: Stumbling And Sometimes Stalls After High Rev Coming Down To Idle
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
Ford Ranger / B-Series :: Extremely High Idle At 2500 To 3000 RPM
Ranger often wants to idle at 2,500 to 3,000 rpm. I'm glad its got a clutch! This is a long term intermittent problem that is getting worse. I have replaced the the IAC twice. I have unplugged the IAC when the engine is in high idle and the engine idles normally. But, starting the car with the IAC unplugged makes car run rough. That makes me think the IAC is not getting the right voltage input from the pmc (eec). Mine is a 2002 with the 3.0 engine. Throttle plate seems to be closed.
What sense inputs does PMC use to determine idle air position? Also replaced TPS sometime ago but that didn't work either. Sometimes turning off the a/c will knock the idle back to normal but not always. Turning the car off completely usually resets idle. But the high idle comes right back after accelerating. Drove the car today and idle would stick and stay high when clutch pushed in coming to a light. However. as the car slowed to a stop the idle would come down when rolling 1-2 mph. ??
Ford Ranger / B-Series :: High Idle At Start Up / Revs Up Over 2000 RPM
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 RepliesFord Ranger / B-Series :: Rough Idle At Start Up - Spark Plug 4 Keeps Going Bad
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesFord Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: 2003 V6 Rough Idle / No Power On Highway
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.