Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: 1995 - Periodic Rough Idle When Warm / Shakes And Misses
My 95 4.0 has had a periodic idle issue for quite a while. It seems it may be getting worse. Here is when it may only happen:
Vehicle is fully warm. I shut it off for about 1 hr or so and when I restart it, it shakes and misses in idle. It will idle fine after I drive it around or if I rev the engine for a while when still parked.
This never triggers the "check engine light". New fuel filter, plugs and wires.
Ford Ranger / B-Series :: 1996 - Running Rough / Smooth Out A Bit When RPMs Raised Up
Recently bought a 96 4 cylinder 5speed 2wd ranger. 200xxx miles on it and its former owner had a young guy change spark plugs . Truck ran fine before, but after is when the rough running showed up.
A quick check of the plug wires and there locations looked correct and also tested the wires for spark with a timing light attached to them, checked shows all are firing.
Seems to smooth out a bit when rpm's are raised up, but still acts like not running smooth.
I swapped out plugs. Looks like they haven't been changed in a long time .Some of the straps are burnt and are shorter than they should be, but still runs rough, very little improvement .
Check vacuum lines for leaks/breaks and all looked good. removed line off brake booster and plugged, didn't matter.
It doesn't throw and check engine lights. It does smooth out some as the rpm's rise, but still not smooth .
Ford Ranger / B-Series :: 2004 - Hard Starting / Rough Idling / No RPMs
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesFord Ranger / B-Series :: 1998 - CEL Started Flashing / Idled Rough But More RPMs Smoothed Out
I have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 RepliesFord Ranger / B-Series :: Hissing Noises And Idle Fluctuate Between 2500 And 3000 RPMs
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
Civic - Honda :: 1995 EX - Rough Idle / Stalling At Low RPMs And Won't Start When Humidity High
1995 Honda EX with 150,000 miles. Its been running rough ie rough idle, stalling at low rpms etc Additionally for awhile now when humidy reached north of 85% the car wont start. It cranks but rarely runs.
Took it to a mechanic last week for a tuneup. They replaced the Distributor cap, spark plug and wires and fuel filter. Car ran great for a day. Then progressively got worse. Was undriveable the other day stalling misfiring while at speed. Took it back today. They determined that it was still not getting spark and replaced the distributor. They did so, test drove it, declared it good and I came to pick it up. Paid the bill, walked out to the car and the damn thing would not start. Humidity was high.
Mechanic pulled a spark plug and put a tester in and didn't get a spark when cranking. He is assuming the distributor he just put in is bad. So they are keeping the car overnight to be fixed in the morning with a new distributor.
However I'm not convinced the dizzy is bad, I believe, as I've read that the Honda's ECU is probably bad and shorting out in the high humidity. Can a bad ECU would prevent spark?
Ford Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: 1998 - Rough Idle At Cold?
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesFord Ranger / B-Series :: Rough Idle At Start Up - Spark Plug 4 Keeps Going Bad
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesFord Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: 2003 V6 Rough Idle / No Power On Highway
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
Ford Ranger / B-Series :: 2002 XLT - Rough Idle - Misfire On Cylinder 3
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Ford Ranger / B-Series :: 2007 - Rough Idle At Low RPM Either In Park Or Drive
2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 RepliesFord Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: 2004 - Rough Idle - CEL With P0303 And P0316 Codes?
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge
Ford Ranger / B-Series :: 1987 - Rough Idle After Start Up / Bogs Down And Wants To Stall
I have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 Replies