Ford Ranger / B-Series :: 1996 - No Running Lights On The Rear End
I have a 1996 ford ranger and i have no tail lights i have license plate lights, brake lights, Hazard and turn signals. But no running lights on the rear end. Where the grounds are for this circuit and if some one has a schematic for this ranger...
View 9 RepliesFord Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: 1995 - Rough Idle And RPMs Drops?
1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 RepliesFord Ranger / B-Series :: 2004 - Hard Starting / Rough Idling / No RPMs
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesFord Exhaust System :: 1987 Ranger - Engine Is Running Very Rough And Seems To Miss At Low RPMs
How many O2 sensors does a 2.3 fi 4 cyl. have. I think just one on the manifold, but I'm not completely sure. Engine is running very rough and seems to miss at low RPMs, has no power and drinks gas like crazy!!! Emissions light is on on the dash. I'm thinking O2 sensor......tried replacing, but couldn't get enough torque on the sensor socket wrench to loosen, may be rusted.
View 6 RepliesFord Ranger / B-Series :: 1998 - CEL Started Flashing / Idled Rough But More RPMs Smoothed Out
I have a 98 ranger with 2.5 and 225k mostly trouble free miles. This engine has never used a drop of oil and ran good. In Dec 3 miles from work started running poorly and sounded to knock the more I asked for power. The CEL started flashing I made it to work and it idled rough but more rpms smoothed out. Took it to mechanic says he did a compression check with little or no compression on #1 & #2. #3 & #4 fine must have broke rings. Doesn't seem right to lose 2 cylinders at the same time out of the blue. Could anything else be causing these symptoms or time for a heart transplant? He hasn't opened anything up yet.
View 6 RepliesFord Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: New Plugs Now Truck Running Rough
Although my lil' truck (2006 Ranger XLT, 2WD,with 4-cyl / 5spd, and 115K miles) has been running just fine since I bought it about a year & 5K miles ago, I suspected it still had its original spark plugs and I figured I should change them before problems arrived.
As I suspected, the plugs that I took out looked to be original. I measured their gap and they all had excessive plug gaps - around 0.052" gap. I installed the four new AUTOLITE APP104 (double platinum) and checked their gap, and they were a bit tight at 0.042". My book says they should be at 0.044" gap. But I installed them at 0.042 anyway, figuring they'll burn wider in time.
One by one, I smeared a small bit of never-seize on the plug threads & at the plug-to-cyl head tapered edge. I smeared a dab of Dielectric Grease around at the top of the plug to ease the plug wire re-install and hopefully calm any possible arching. The plug wires came off the plugs easy enough and went back on just as easy.
I hit the key and the engine fired right up. It idled rough as expected. However, it continued to idle rough and if I raised the RPM level, it would respond, but still ran rough. It is throwing a 'Check Engine Light' on the dash cluster now - whereas it wasn't prior to the new plugs.
Ford Ranger / B-Series :: 2002 - Running Rough Like Misfiring
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl
Ford Ranger / B-Series :: 1999 - Running Rough / Missing And Surging At 50 To 70?
I live in Kansas and was home in Georgia for the last 2 weeks. The truck drove great there after a fuel up started missing and surging at 50 to 70 thought it might have been bad fuel. waited till it was low added Lucas fuel treatment and premium gas still was doing it. no check engine light. went to Advance and fuse for light was blown they checked and was getting mass air flow code. unplugged it and seemed to be better, not perfect but better. plugged it back in and went to do it again. Changed mass air flow night before the drive back to Kansas. Ran well from Savannah to north Georgia then started doing it again the rest of the way home. Going to have advance check code again.
View 12 RepliesFord Ranger / B-Series :: 1998 - Running Rough And Now Getting P1151 Code
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 RepliesFord Ranger / B-Series :: 2003 - Misfire And Rough Running / Flashing CEL
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
Ford Ranger / B-Series :: 1990 - Rough Start - Running Lean?
]I recently bought a 1990 ford ranger with a 2.9 @187,000 miles. That being said I went through and changed a few vacuum lines, the oil, air filter, pcv/grommet, and fuel filter.
The problem is it hates to start. I could crank on it for 10 seconds and not a single thing. Sometimes if i turn the key to the off position, wait a second, and try again, Ill get the truck to fire. When it does fire up it just reeks of the lean exhaust. It also gives me some hesitation when I rev it. I did a fuel pressure test (KOEO) last night and it gave me 32 psi and within a minute the needle fell to about 25 psi. I hear the fuel pump run for only 2-3 seconds too.
I've already pulled the MAF off and cleaned it, replaced the TPS, and did a fuel pressure test. The fuel filter is brand new
Ford Ranger / B-Series :: 2000 3.0L Running Rough / Shuddering At Stops
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
Ford Ranger / B-Series :: Sputtering / Rough Running Situation Once Warmed Up
'86 Ranger, 2.3L, Automatic transmission.
Been having a sputtering/rough running situation once warmed up, replaced every so often with open loop smooth running. Lately, have had several occasions where the truck stalls and will not restart after a hard right turn (fuel pump powers up, tho) After 30 or so minutes of repose, truck will restart and run.
Recent History:
During the last 1-1/2 years, had cylinder head rebuilt and reinstalled. Had to run it all winter w/o EGR tube attached because of bad fitting at exhaust manifold. Replaced the fitting last spring and replaced cat back exhaust system. Had manifold hole plugged with pipe plug all winter. Have had a diagnosis of poor compression in the past, have not rechecked compression since head rebuild, but did have a noticable increase in power.
Have checked base ignition timing and it is correct. Valve timing appears to be as it should be. Have not had the opportunity to check for spark during one of the breakdowns, since I had no tools and it was night time.
The codes:
Early in Fall, got 14, 21, 24, 34. The 14 particularly interested me, as it suggests ignition problems.
Just before pulling the distributor, I checked codes again; 14 had disappeared as did 34 (EGR issues I resolved above) but I still got 21 (coolant temp out of range) and 41 (no HEGO switch) So I left the distributor alone and replace the HEGO sensor and cleared codes.
Last code check, just got 21(coolant temp sensor voltage out of range) and 24(air charge or Vane air temp voltage out of range) There is very little heat on cold days, full radiator and I've "burped" the cylinder head on an incline more than once chasing trapped air.
I'm suspicious of the TIF module, since the stalling is after warm up and self corrects. It was replaced once perhaps 12 years ago.
Ford Ranger / B-Series :: 1985 - Running Rough - Bogging Out And Stalling
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 RepliesFord Ranger / B-Series :: 1987 - Running Extremely Rough / Exhaust Smell
I have a 87 ford ranger pickup, it is running extremely ruff. You can smell the exhaust and it smells super rich and is even spitting fuel out of he exhaust. when I bought the truck the wires were cut on he oxygen sensor, so I put a new oxygen sensor in it hoping that it would lean out the fuel. The truck has duel tanks on it, but the back one is off and it is draining fuel out of the line when it is running. I don't know if the catalytic converters are plugged too, the truck only has 65,000 miles in it. or maybe its a vacuum line leak?
View 4 RepliesFord Ranger / B-Series :: 2000 - Running Rough And Code For Misfire On Cylinder 3 / 2nd Coil Pack
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesFord Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies