Ford Ranger / B-Series :: Hissing Noises And Idle Fluctuate Between 2500 And 3000 RPMs
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
Ford Ranger / B-Series :: 1997 V6 - High Idle At 2500 RPM When IAC Is Plugged And Steady 1100 When Unplugged
I have a 1997 Ranger with a 3.0 v6 with a super high idle.
It idles at 2500 RPM when the IAC is plugged and a steady 1100 when unplugged. I have replaced the IAC twice now (dropped the first replacement. long story) and and have also checked for vac leaks with no results.
After about 2-3 minutes of idling at 2500 on a cold start it will drop down to 1100 (same as when IAC is unplugged), but after a 10 minutes or so drive it will idle steady at 2500 with minimal if any dropping in RPMs. This is driving me crazy not only because it sounds horrible but also because of the fact it's burning through fuel like it's going out of style.
I have checked the MAF sensor and it looks brand new (not the original owner) along with the O2 sensor. I have been meaning to check the TPS voltage to see if it's working correctly but without a working multi-meter it's making it difficult to do anything.
I'm at a loss with this right now and because of all the previous repairs i have done to it and the others that still need to be done i don't have the biggest budget to fix this problem nor the money the truck is using in gas.
Ford Ranger / B-Series :: 2008 XLT Cuts In / Out When Idle It Up At 3000 RPM
Driving a 2008 Ranger XLT 3.0. Starts runs and drives fine, how ever it seems to have a tinny ruff idle.
What I noticed is when in park or neutral when I idle it up @ 3000 RPMs it seems like it runs on 3 cylinders and sort of cuts in and out very quickly. Is this a protection thing on the ranger.
Running on the road it kicks down and runs thru all the gears normally from idle all the way up to 5000 RPMs. Just would like to make sure this is normal.
Ford Ranger / B-Series :: 1990 - Extremely High Oil Pressure / Heavy Smell Of Burning Oil
I own a 1990 Ford Ranger, 2.3 EFI with an 8 Plug setup and 2WD. It uses a dual-coil system an not a distributor if that means anything here.
Okay, so for the last week I have been experiencing extremely high oil pressures. My gauge would read almost as high as the "H" mark. The smell of burning oil was heavy in the cab from the vents. I took it easy, made sure my oil level was good and I had enough oil, the truck drove rough, but drove decent.
Yesterday, I got done sliding in some mud (not crazy bouncing or anything, just sliding). I stopped at a stop sign, turned around and hit the gas, and the truck died. I thought there were other issues not related to oil, however I noticed that the oil gauge now read about an inch left of the "L"ow mark. If I turned the key, to the "ON" position, the gauge pushed the needle to above the left gauge itself pointing towards about the "8 oclock" area.
Now, my truck will not start. It cranks and cranks and cranks with no start. I called a bunch of mechanics and none of them knew what I should do. AutoZone did not know what do, no one did. Some people said that the oil pump itself had gone out and that would cause the truck not to start and would cause gauge issue. Others said that it might be as small as the Oil Pressure Switch. Firstly, I bought a new Pressure Switch. Have not installed it because I cannot find the damn thing.
Where the switch OFFICIALLY is. I have read on Google that it is on the passenger side, at the rear end of the cylinder head. Other posts say it is by the oil filter...
PICTURES:
Without the key in the ignition:
With the key in the ignition, in the "ON" position:
Ford Ranger / B-Series :: 1999 - High Idle - ECM?
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
Ford Ranger / B-Series :: 1992 - Very High Idle At About 3500 RPM
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 RepliesFord Ranger / B-Series :: 1987 XLT - High Idle When Started For About 6 Minutes
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 RepliesFord Ranger / B-Series :: Stumbling And Sometimes Stalls After High Rev Coming Down To Idle
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: High Idle At Start Up / Revs Up Over 2000 RPM
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 RepliesFord Ranger / B-Series :: 2003 3.0 V6 - High Idle In The Mornings When Cold About 2000 RPM
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
Ford Ranger / B-Series :: 2003 - High Idle And Shoot Up Between Shifts / No Codes
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
Ford Ranger / B-Series :: High Idle / 2600 RPM When Pushed The Clutch In Approaching A Light
I have a 1997 Ford Ranger XLT 6 cyl. 4 wheel drive. I got this truck from a friend. Only had it for a month or so has about 185K on it but has been running great.
I did notice a couple times that when I pushed the clutch in approaching a light the truck would jump a bit in RPM to about 2600. but go back down in a second or two.
This started to occur more frequently and now it does it almost all the time....when I push clutch in it revs up to about 2600 RPM.
Now I can have my foot on the brake and let the clutch out to put some strain on the engine and knock the RPM down but its still a bot high in the 1k range. Sometimes it actually goes back to normal...
When I started it this morning it was fine....but after two shifts it started and lasted the 12 miles to work. What could be causing this? It does not seem to go above 3000 RPM when it revs.... Other then that the truck runs great.
Ford Ranger / B-Series :: 1998 Won't Go Over 3000 RPMs
I have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
Ford Ranger / B-Series :: 2003 4.0 - Rev Limiter At 3000 RPM / AC Clutch Not Engaging?
So that's what if feels like, in park at idle it sounds great, starts great no codes. IF you floor it it will not go over 3000 rpms in park, it feels like it has hit a rev limiter. I have 60psi fuel pressure at idle and at 3000 rpm.
When driving down the road I won't go over 55 mph and drives normal if you keep it under 3000 rpm, if you give it more gas it falls on its face?
AC is not working (clutch not engaging)I don't know if that's related or not.
We did just swap the motor the truck is a 2003 2wd drive. motor came out of an 2002 4wd. we are running the 2wd harness, computer egr delete etc.
Ford Ranger / B-Series :: 1987 - Running Extremely Rough / Exhaust Smell
I have a 87 ford ranger pickup, it is running extremely ruff. You can smell the exhaust and it smells super rich and is even spitting fuel out of he exhaust. when I bought the truck the wires were cut on he oxygen sensor, so I put a new oxygen sensor in it hoping that it would lean out the fuel. The truck has duel tanks on it, but the back one is off and it is draining fuel out of the line when it is running. I don't know if the catalytic converters are plugged too, the truck only has 65,000 miles in it. or maybe its a vacuum line leak?
View 4 RepliesFord Ranger / B-Series :: 1996 Truck Idles From 500 RPM And Randomly Jumps Up To 2 - 3000 RPM Then Back Down
I have a 96 ranger with the l4. Right before I bought my newish truck last December, it's started miss firing and running really bad. I replaced the spark plug wires, most of the spark plugs, and both coil packs. Didn't work at all. Then I bought my new truck and parked. Fast forward to now. Fired it up, ran REALLY bad. We changed the wiring order from the 96 order to the 99 order.
But the truck idles from 500rpm (barely running) and randomly jumps up to 2-3000rpm and then back down. Driving it has NO power, rev it and it stays at 2-3000 for quite awhile. Sometimes it randomly dies. REALLY need to get it running quick and cheap. Getting ready to sell my daily driver to find something else and I need something to drive while I hunt for another truck.
Ford - Thunderbird :: 1993 - High Idle Around 2500 RPM
I have a '93 Thunderbird 3.8 v6, auto trans, that was a great running car until I had the water pump replaced. So, I got the pump replaced and then 1 day later the car started to idle around 2500 rpm. It would hit about 45mph without even giving it any gas. I swapped out the mass air flow sensor for a new one. This brought the idle down a little bit. A month later, it shot back up.
View 2 RepliesFord Escape / Hybrid :: 2003 - High Idle / RPMs Shoot Up To About 3000
When I start my 2003 Escape 3.0, the rpm's shoot up to about 3000rpms. After a few seconds they drop to about 2000 and slowly creep back up to 3000. When I put in gear, I don't even have to step on the gas and my vehicle goes. It maintains between 1500-2000rpms as I'm driving. When I come to a red light or stop sign, it lurches like it wants to go even though I have my foot on the brakes. I've replaced the IAC valve, TPS, had it checked for vacuum leaks, PCV valve replaced. I'm at a loss as to what it could be.
View 3 Replies