Ford Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
Ford Ranger / B-Series :: 1990 XLT V6 - Loud Constant Whistle Sound On Driver Side
So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.
View 3 RepliesFord - Ranger :: 1990 Will Turn Over But Isn't Firing
199) Ford Ranger will turn over but isn't firing. We've replaced the battery, positive battery cable, distributor, distributor wires, the selonoid inside the distributor, starter selonoid.
View 18 RepliesFord Ranger / B-Series :: 1986 - Engine Won't Firing
i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is
View 1 RepliesFord Ranger / B-Series :: Runs Rough - Driver Side Exhaust Manifold Cold / Passenger Side Hot?
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
Ford Ranger / B-Series :: 1994 - Sputtering / Back Firing / No Power
Background - I just got done changing a few things... Exhaust Manifold/gasket, battery cables, valve cover gasket, oil cooler gasket and hoses, power steering pump and hoses, and ball joints. Most of this has nothing to do with the issue that came up as I am driving it back to return it to her.
While out on the freeway, I initially notice subtle power losses and surges. These quickly escalate into almost total power loss with back firing, sputtering and much more noticeable surges in power. The check engine light was turning off then on a few times before pretty much deciding to stay on.
So I nurse it back home on back roads due to its inability to maintain freeway speeds. I proceed to check everything I touched paying special attention to the exhaust manifold and surrounding area. The new manifold came from the j/y and was barely used so I had initially just stuck with the O2 sensor that came with it; I changed this to the one the vehicle had previously been employing as it was not exhibiting these symptoms until after the job was done. I also double checked all the hoses, intake tube, wires and connectors; everything is connected.
From here, I research the method of pulling codes on OBD-1 vehicles by making the check engine light flash. It flashed a 111 and a 172 at the same time; the information I could find said the 111 means everything is normal, and the 172 suggested O2 or MAF. I am reasonably sure the O2 is not the problem so I focused on the MAF. Disconnecting it while running seemed to improve the way it idled so via the process of deduction, which also included the consideration of typical symptoms of MAF sensor failure, I proceeded to replacing the MAF sensor which amounted to little improvement.
At this moment in time the check engine light has not returned but it is clearly not in a drive-able state of being. It actually seems to have ever so slightly improved though.
Additionally, the symptoms only exist when the engine is hot and has been driven; it drives normally for 5-10 minutes until it gets to operating temperature then it starts to crap out. After changing the MAF sensor, I let it idle for 20 minutes and it was fine until about 2 minutes into the test drive.
Speculation - I am thinking spark plugs could also be a culprit as its has been forever since a tune-up but the sudden onset of this condition make me doubt this a little; it also has 8 plugs so even if one or two crapped out it should still run better than this I would think.
Ford Ranger / B-Series :: Driver Side Headlight Go Out
I've got an 08' Ranger FX4. Recently I had the drivers-side headlight go out. Today I replaced the light, and while I was there, I decided to check every bulb on the truck. Everything else works, but I noticed the 2 factory "foglights" will not come on. This is a fairly recent development, because I use those lights quite often.
Even thought they don't cast a huge amount of light, here in the Vancouver area, winters are dark & rainy, so I think 4 points of light as opposed to 2 points is a benefit. To activate those lights, you pull on the headlight selector switch. Do those lights have their own dedicated circuit with fuse? Or does this sound like a switch problem?
Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesFord Ranger / B-Series :: 1987 Truck Won't Start / Ignition Firing While Key On Engine Off
I've got an 87 ford ranger 4x4. The truck won't start. The ignition is firing off with the key on engine off. When I got the truck the transfer case was blown. The people I got the truck from drove it to here it sat. I check the wiring but the transfer case to make sure it diet get damaged causing a sort. When I got the pcm was missing. Took one out of a bronco 2 and changed the relays on the fender. Here what I've done so far
Relays
Pcm
Complete tune up.
Distributor and ignition module
Replaced and repair some grounds.
Ford Ranger / B-Series :: 1998 - Oil Leaking Somewhere On Driver Side
I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.
Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.
Ford Ranger / B-Series :: Burning Oil / Coolant In Cylinder 3 On Driver Side
I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
Ford Ranger / B-Series :: Hub Spins On Driver Side But Tire Won't Engage
1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.
View 14 RepliesFord Ranger / B-Series :: 1996 XLT - Front Driver Side Spindle
I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.
I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.
1996 Ford Ranger XLT 2.3 ......
Ford Ranger / B-Series :: 2003 - In Every Few Seconds Chirping Noise On Driver Side?
I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?
View 4 RepliesFord Ranger / B-Series :: 1997 4.0L - 0 PSI Compression On 3 Cylinders
I've been fighting some issues with the truck and decided to do a compression test to decide if I want to try to keep 'Old Yeller' alive or not. I'm all for working on it until I have to dig into the lower end of the motor. I rented a compression tool and the results were a little shocking. I did this test with a slightly warm motor, fuel pump relay pulled, all spark plugs pulled and throttle @ 100 %. Motor turned over 10 times for each cylinder. I even moved all the rubber o-rings on the tool up on the threads to make sure I was getting a good seal.
Cyl 1 - 40
Cyl 2 - 0
Cyl 3 - 0
Cyl 4 - 80
Cyl 5 - 0
Cyl 6 - 60
Needless to say I didn't even bother doing this wet. My only real question is can this be close to accurate. I drive the truck daily. 160k mi on it.
I'm fighting the dreadful P0171 and P0174 codes and after a couple cycles I will get misfire codes. Its low on power (hard to keep @ 70MPH with some wind) and gets 10MPG right now. However it starts and runs and stays consistent (even though it rumbles like it has a nice cam in it).
Is it time to put Old Yeller down ? Are these compression results even remotely accurate ?
Ford Ranger / B-Series :: 2001 V6 Only Runs On 2 Or 3 Cylinders
My 2001 V6 Ford Ranger Edge has 124, 000 miles and always ran very well, Shortly after a minimal attempt to pull a vehicle out of a ditch the vehicle began to run poorly. This may be coincidental as problem did not begin straight away. The engine refused to start at first but now appears to run on 2 or 3 cylinders. I have checked AND CONFIRMED the following:
Spark at all cylinders
Fuel filter replaced
Fuel pump checked
Fuel pressure 56 psi at schrader valve on fuel rail
Fuel inertia cut off valve checked
E_Z start sprayed in feed horn did nothing
I hope to avoid towing it to the dealer,as I recently had a very negative experience doing this with the Honda dealer..
Ford Ranger / B-Series :: Constant Thud Coming From Front Driver Side While Driving
When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?
View 3 RepliesFord Ranger / B-Series :: 2002 4X4 - Loud Bang / Pop Comes From Driver Side Front Tire
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
Ford Ranger / B-Series :: Vacuum Lines Bad On Driver Side / Actuators Won't Disengage Properly
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).