Ford Ranger / B-Series :: 2006 3.0L - Intermittent Low Compression And Misfire At Idle
I bought a used Ranger a couple months ago and it ran fine when I test drove it but a week later it started having a misfire every now and then at idle.. I must have gotten pretty unlucky with the test drives..
The misfire comes and goes, it will run fine for a week or two and then it will misfire at idle for a week or two. It only seems to misfire at idle, the truck runs rough/shakes but once you give it a little gas and start moving it goes away. Usually it has a check engine light on from startup when it's misfiring and it goes away on days that it's running fine; it will occasionally misfire at idle with no check engine light. Sometimes when its running really rough the CEL flashes while it's misfiring at idle and I've actually restarted it real quick and the misfire went away for a bit. The engine codes that come up are misfire on startup and misfire on cylinder 4.
I've tried cleaning the MAF sensor, replacing the fuel filter, testing for spark and compression. Compression was 150-155 PSI on all cylinders, however, the compression on cylinder 4 is different depending on whether the truck is running well or not. When it's misfiring the compression on cyl. 4 is 90 PSI and when it's running fine it's 150 PSI. I'm not sure what could be causing intermittent low compression like that?
Ford Ranger / B-Series :: 2001 V6 Only Runs On 2 Or 3 Cylinders
My 2001 V6 Ford Ranger Edge has 124, 000 miles and always ran very well, Shortly after a minimal attempt to pull a vehicle out of a ditch the vehicle began to run poorly. This may be coincidental as problem did not begin straight away. The engine refused to start at first but now appears to run on 2 or 3 cylinders. I have checked AND CONFIRMED the following:
Spark at all cylinders
Fuel filter replaced
Fuel pump checked
Fuel pressure 56 psi at schrader valve on fuel rail
Fuel inertia cut off valve checked
E_Z start sprayed in feed horn did nothing
I hope to avoid towing it to the dealer,as I recently had a very negative experience doing this with the Honda dealer..
Ford Ranger / B-Series :: Getting Good Spark From All Cylinders But Not Starting
I just finished rebuilding my 1990 2.9 and it wouldn't start. When we did the initial start up, the truck needed ether to start and ran decently while stumbling. I found out that the spout connector was removed from the previous owner so I spliced it but still no starting ...
I installed a new fuel filter, fuel pump, cleaned the injectors, spark plugs, spark plug wires, distributor cap, rotor, air filter and cleaned the MAF. ..
Its not a spark problem because I'm getting good spark from all the cylinders and yes the timing was set correctly. It sounds like it wants to start but just doesn't have something to make it boom. There are also no codes...
Ford Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 RepliesFord Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
Ford Ranger / B-Series :: 2003 - Multiple / Random Cylinders Misfiring
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 RepliesFord Ranger / B-Series :: 2003 - Missing On 3 Cylinders Randomly / Lean Fuel
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
Ford Ranger / B-Series :: Erratic Idle / Sporadic Miss / 3 Cylinders On Right Bank Dropping In And Out
Its a 1994 with 4.0, automatic, 4x4. Running fine, parked it, a week later I'm getting a bad but sporadic miss that according to the stealership is the 3 cylinders on the right bank dropping in and out. Driving down the road you can feel them drop out and when they come back its a kick in the pants like a turbo kicked in.
Shop says wires are good, plugs are good, and then lost me when they started talking around in circles and not making much sense.
What could make 3 cylinders all on the same side of the engine drop in and out? This wasn't anything that slowly came on. Fine one day, crap the next. The only thing I did prior to was replace the IAC because it was idling high, it was cruddy inside, and it looked like it was original. It was running fine after that till this issue popped up out of nowhere.
Mileage was claimed to be 178k but I'm beginning to suspect it's probably 278k.
Ford Ranger / B-Series :: Truck Sputters - Cylinders 2 / 3 And 4 Misfiring - Bank 1 And 2 Running Lean
I have a 99 ford ranger xlt 4.0 ohv basically it sputters so bad while driving it sounds like a dump truck but it all started when I changed my o2 sensors but in doing so I broke my heater control valve and when I was going down the road it started sputtering well it started sputtering so I checked the o2 sensors there good and I changed the heater control valve. But nothing so I changed my coil pack spark plugs and wires but still nothing. But on my reader it says cylinders 2,3, and 4 are misfiring and bank 1 and 2 are running lean plus it has a bad aroma of gas in the engine compartment but when it idles its somewhat smooth but when I'm driving it its horrible the sputtering is so bad it takes awhile to get up to speed plus I'm only getting 100 miles to a whole tank that's like 8 or 9 mpg I need to fix this soon. This is my only transportation...
View 11 RepliesFord 6.0L Power Stroke Diesel :: Low / No Compression On All Cylinders
It's at 65k miles, was sitting around for half a year with a previous owner. Started with hpo issue that I seem to have resolved with new ipr. I'm also doing injector seals, nipple cups and dummy plugs in the meantime to seal off the system.
I had ran a compression test with a 300psi gauge on a couple cylinders as I was changing glow plugs and harness, and they showed above 350 psi. A couple others showed barely 150, so I figured I blew up the gauge. That's when I went and bought a harbor freight diesel gauge and while I was waiting for the otc adapter whip to come in I took apart the oil rail and was getting ready to do injector seals and nipple cups.
I have now tested all the cylinders with the proper gauge but only to get the same dreadful result low compression ranging from 150-200 and rising 50 only with a bit of oil added to the cylinder.
If I don't have compression I'm obviously not going to get it to start although everything else showed up good on the torque gauges before it was apart. Why I don't have compression on any cylinders? I'm getting a new compression gauge today just in case, but seems unlikely it's the gauge.
Ford - Engines - Escape :: 2008 - One Of Six Cylinders Has Compression Rate Of Only 25
My mechanic just told me I have one of my six cylinders that has a compression rate of only 25. I am weeping as I continue to pay my car loan. Looking for info, if this can be repaired vs. putting in a replacement engine?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Burning A Lot Of Oil / Low Compression On 2 Cylinders?
2000 f450, truck has been running great and then all of a sudden starts running really rough. I check the oil and its dry! it was 9 quarts low! i checked the oil 2 weeks prior as i often do. i change the oil every 4500 miles and now this. i had driver side injectors done about 5 months ago. I take it to my mechanic and he said he thinks it has low compression on 2 cylinders but didn't do a compression check( not sure how he knows). He told me to run it until it pukes , keep putting oil in it with lucas oil additive. Then i will have to have the engine rebuilt. The truck only has 175000 miles! i thought these things were supposed to run forever! Does this seem right to you guys? I bought the truck a year and a half ago and have always kept up with it. has dp tuner but everything else is stock. Smoke comes out of the oil fill tube slowly but doesn't send puffs like a locomotive. mechanic said the turbo is fine.
View 14 RepliesFord Super Duty (1999-2016) :: 2015 F250 - No Compression On 3 Cylinders
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
Ford Super Duty (1999-2016) :: 2000 F250 5.4 - No Compression On Cylinders
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 RepliesFord 6.0L Power Stroke Diesel :: Low Compression Results - Slight Brown Haze On Cylinders
While I had my glow plugs out to crank the motor for the HPOP work I have done I checked the compression on all the cylinders. 6 of the cylinders were 275-280, got 250 and 110 on the others. I put oil in both the low cylinders and the 250 went to 260 and 110 went to 150. I pressurized the low cylinder and with the valves closed it was leaking out the exhaust manifold also had a small amount of coolant come out the water pump. Removed the cylinder head and didn't see anything unusual with the cylinder that was reading low in fact the if was the best looking cylinder of the four with nice looking crosshatch on the cylinder wall.
The other three cylinders has some slight brown haze on them which I assume is rust. This motor probably hasn't run in 18 months and the truck was a non-runner when I purchased as a theft recovery, no history on the truck. Taking the one head to a shop for them to check it out. What's the opinions out there with the low compression? Be ok once it runs and rings get coated with oil? The motor is out of the truck so maybe I should tear it down completely hone and put new rings in it.
Tiguan :: 2011 Engine / No Compression On All 4 Cylinders
I had My VW tiguan 2011, Died all of a sudden, where went to supermarket and went out and the car is not starting at all.
So next morning had it towed to the dealership for investigation. Now after a week of tests and investigation and replacement of Fuel HP pump @ the engine still not working.
They did pressure test, and surprise came "no compression on all 4 cylinders".
They will need to open the engine and do further investigation. Hope it's just a gasket leakage
The car is still less than 5 years and mileage is 174K km, just made oil top up and general checks few days before the incident. all services @ dealership if not on-time, before time.
Lexus GS 2006-11 :: Car Died In Parking Lot - No Compression On All Cylinders
Wife's 2008 ES350 with 80k miles died in a parking lot. Wouldn't re-start with warning lights for Trac Off, Check Engine and VSC. Called tow truck from our local repair shop. Tow truck driver tied and started the car with no lights. Wife went ahead and had it towed.
Repair shop called and said that car started for tech but died w/o any warning lights. Shop started checking it out and found that it has no compression on all cylinders. In talking with service manager, we discounted the timing chain since the car will re-start, at least a few times. His gut feeling, something with the internal timing gears and such.
Repair shop has found a used engine locally and has it on hold while we decide what to do. The shop doesn't rebuild motor and just diving into it for exploratory surgery could be expensive with no assurance of positive results.
Ford Ranger / B-Series :: 1997 - Possible 4.0 To 5.0 Conversion?
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 RepliesFord Ranger / B-Series :: 1997 - Won't Go Into Park?
Went to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.
View 6 Replies