Ford Ranger / B-Series :: 1987 Truck Won't Start / Ignition Firing While Key On Engine Off
I've got an 87 ford ranger 4x4. The truck won't start. The ignition is firing off with the key on engine off. When I got the truck the transfer case was blown. The people I got the truck from drove it to here it sat. I check the wiring but the transfer case to make sure it diet get damaged causing a sort. When I got the pcm was missing. Took one out of a bronco 2 and changed the relays on the fender. Here what I've done so far
Relays
Pcm
Complete tune up.
Distributor and ignition module
Replaced and repair some grounds.
Ford Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
Ford Ranger / B-Series :: 1986 - Diesel Swap - Engine And Trans Combos?
I have A 1986 ranger with a 2.9 v6. I am thinking of doing a diesel swap and I am wondering what engine and trans combos would work best for this. I was thinking 4bt but there are may other options that could work.
View 14 RepliesFord Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 RepliesFord Ranger / B-Series :: Coil Is Sending Spark But Cylinders 4 / 5 And 6 Not Firing
Al right i have a 94 ranger 4.0 4x4 auto 186k ... The truck has new bosch double plat plugs gaped .054, new wires, MAF, TPS, FPR, O2 sensors, ECTS and I checked the intake air charge sensor and is fine ....
My issue is cylinders 4,5 and 6 dont fire... the coil is sending a spark, i can pull the plugs one at a time and watch them fire (strong blue spark)... All fuel injectors do not leak and spray a perfect cone out of all 4 holes and noid light test is good ...
The truck runs like crap back firing and no power under 4k and i can pull off all 3 wires for bank one and it make no difference and when i unplug the injectors no more back fire....
Ford Ranger / B-Series :: 1994 - Sputtering / Back Firing / No Power
Background - I just got done changing a few things... Exhaust Manifold/gasket, battery cables, valve cover gasket, oil cooler gasket and hoses, power steering pump and hoses, and ball joints. Most of this has nothing to do with the issue that came up as I am driving it back to return it to her.
While out on the freeway, I initially notice subtle power losses and surges. These quickly escalate into almost total power loss with back firing, sputtering and much more noticeable surges in power. The check engine light was turning off then on a few times before pretty much deciding to stay on.
So I nurse it back home on back roads due to its inability to maintain freeway speeds. I proceed to check everything I touched paying special attention to the exhaust manifold and surrounding area. The new manifold came from the j/y and was barely used so I had initially just stuck with the O2 sensor that came with it; I changed this to the one the vehicle had previously been employing as it was not exhibiting these symptoms until after the job was done. I also double checked all the hoses, intake tube, wires and connectors; everything is connected.
From here, I research the method of pulling codes on OBD-1 vehicles by making the check engine light flash. It flashed a 111 and a 172 at the same time; the information I could find said the 111 means everything is normal, and the 172 suggested O2 or MAF. I am reasonably sure the O2 is not the problem so I focused on the MAF. Disconnecting it while running seemed to improve the way it idled so via the process of deduction, which also included the consideration of typical symptoms of MAF sensor failure, I proceeded to replacing the MAF sensor which amounted to little improvement.
At this moment in time the check engine light has not returned but it is clearly not in a drive-able state of being. It actually seems to have ever so slightly improved though.
Additionally, the symptoms only exist when the engine is hot and has been driven; it drives normally for 5-10 minutes until it gets to operating temperature then it starts to crap out. After changing the MAF sensor, I let it idle for 20 minutes and it was fine until about 2 minutes into the test drive.
Speculation - I am thinking spark plugs could also be a culprit as its has been forever since a tune-up but the sudden onset of this condition make me doubt this a little; it also has 8 plugs so even if one or two crapped out it should still run better than this I would think.
Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesFord Ranger / B-Series :: 1986 Just Cranks But Won't Start
I have heard from a few people that it might be the computer that is messed up. Just replaced cap and rotor, spark plugs, wires, fuel filters. Pump turns on. Cranks and cranks but won't start. Took the intake cover off and tried starting it, all it did was back fire. Checked the firing order and everything is right. So im left with guessing at the computer and ignition??
View 5 RepliesFord Ranger / B-Series :: 1986 - Bogs Down When Put Into Throttle
1986 Ranger 2.3 inline 4
I just recently bought an 86 Ranger from a friend. It had recently stopped working and had no desire to fix it. So here I am. The truck will sit in park and rev all day long, once its in drive it idols fine and moves its self down the street. The problem occurs when I apply throttle. It begins to bog down and I cannot get past 20mph. I have replaced the fuel regulator and also I took the tank down and replaced the fuel pump. The fuel filter is two months old, and the throttle response sensor is two weeks old.
Ford Ranger / B-Series :: 1986 - How To Disable Front Differential
My front diff is busted, and I mean bad.. I can barely even run the truck 5mph, and it's very loud. The diff casing is even busted. I want to just disable it to drive in 2wd. What's the easiest way to do it? It won't disable using the push button control.
Can I just remove all the locking stuff in the front wheels, so there's nothing for the axles to grab on, and manually turn the solenoid at the transfer case to shut off the front wheel axle?
Ford Ranger / B-Series :: 1986 - Stalls When Hot / Won't Restart Until Cool
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord Ranger / B-Series :: 1986 - No Fuel To Rail / Truck Quit On The Way
I have a 86 ranger 2.9 5 speed. A few days a go I replaced the front fuel filter and all seemed ok. Last night on my way home the truck quit and I had to have it towed home. Now I find both pumps don't seem to be working. What would make me loose both pumps??
View 11 RepliesFord Ranger / B-Series :: 1986 - Fuel System Wiring Diagrams?
Looking for the wiring diagrams for 86 ranger fuel system. I replaced the fuel pump relay after testing and finding that it was bad, still not getting fuel. I want to test any fusible links or anything else that could have gone wrong before I throw another part at it.
View 1 RepliesFord Ranger / B-Series :: 1986 - Brake Light Fuse Keeps Blowing
I've got an 86 ranger sport and I'm having trouble with the lights. The turn signals work, and ALL 4 bulbs in the back are new. The brake light fuse keeps blowing, and the fuse for the tail lights is good but they won't come on at all. I was told there was a direct short somewhere, does that sound about right? And is there a common place where they tend to short out?
View 2 RepliesFord Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?
But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 RepliesFord Ranger / B-Series :: 1986 - Start Over Fuel - Idles Very Roughly - Stalls Out?
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 RepliesFord Ranger / B-Series :: 1986 - Stalls / Idles Or Runs Roughly And Will Miss Erratically
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 Replies