Ford Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing
Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?
View 1 RepliesFord Ranger / B-Series :: Getting Good Spark From All Cylinders But Not Starting
I just finished rebuilding my 1990 2.9 and it wouldn't start. When we did the initial start up, the truck needed ether to start and ran decently while stumbling. I found out that the spout connector was removed from the previous owner so I spliced it but still no starting ...
I installed a new fuel filter, fuel pump, cleaned the injectors, spark plugs, spark plug wires, distributor cap, rotor, air filter and cleaned the MAF. ..
Its not a spark problem because I'm getting good spark from all the cylinders and yes the timing was set correctly. It sounds like it wants to start but just doesn't have something to make it boom. There are also no codes...
3000GT/Stealth :: Cylinders 3 And 6 Not Firing - No Voltage To Coil
97 SL ATX - Not firing on cylinders 3 and 6; no voltage to that coil.
I've checked:
Plugs
Wires
Coils
PTU
ECU
Timing
So I guess the CAS is the next best guess. So where exactly IS the CAS...and how do i test it? Also, where is the timing mark on the crank pulley? Cams are all aligned but I didn't see a mark for the crank and don't know where I should be looking.
Ford Ranger / B-Series :: 1985 - Truck Simply Quit / No Spark At The Coil / Cranks Just Fine
85 2.0L Dura Ranger.
All of the Idle control wiring and box and sensors have been removed; all else is original. The truck ran just fine after the removal of the above paraphernalia (years). The truck simply quit, no spark at the coil, cranks just fine. All of the wiring has been checked for continuity. The Following components have been replaced with new:
Ignition switch.
Coil.
Dura-spark Box.
Dist coil.
Starter solenoid.
Rotor & Cap.
Plugs and wires.
Correct voltage is present at the coil & D-spark box side of the connector.
Coil tests close to what I think is correct for resistance and the engine ran with it.
I have tested both sides of every connector. I'm not sure what the output side of the D-Spark box (blue tab) voltages should be, and I am unable to test the trigger signal at the coil, however with no output and power in I'm guessing that is the problem...
Taurus :: 2006 Ford - No Spark On Two Cylinders - Code P0352 / Bad Coil
Have a 2006 Ford Taurus that has two dead cylinders. Cylinder 3 and 4. Code says bad coil. I replaced with new coil and plugs. Same problem. Replaced wires and same problem.
Car has 65K. What is causing both cylinders to be dead? Pulled wires off while running and no spark on 3 and 4.
Ford Ranger / B-Series :: Oil Pressure Sending Unit Location
3.0 - Where is located ?
View 2 RepliesFord Ranger / B-Series :: 1986 - Engine Won't Firing
i have a 1986 ford ranger with a bored out 2.9 v6 that is not getting spark sent to the spark plugs disrtibutor has been changed along with spark plug wires any clue what the problem is
View 1 RepliesF Series :: 87 F150 5.0 - No Spark From Coil
Here we go again. shut my 87 F150 5.0 off when I got to work when it was time to leave no spark from the coil, same as 3 weeks ago. First thing I did was pull the new dist and replace it nothing, so I pulled out the new coil still nothing, its getting power to the coil so I would assume the relay is good .
View 4 RepliesFord Ranger / B-Series :: 1994 - Sputtering / Back Firing / No Power
Background - I just got done changing a few things... Exhaust Manifold/gasket, battery cables, valve cover gasket, oil cooler gasket and hoses, power steering pump and hoses, and ball joints. Most of this has nothing to do with the issue that came up as I am driving it back to return it to her.
While out on the freeway, I initially notice subtle power losses and surges. These quickly escalate into almost total power loss with back firing, sputtering and much more noticeable surges in power. The check engine light was turning off then on a few times before pretty much deciding to stay on.
So I nurse it back home on back roads due to its inability to maintain freeway speeds. I proceed to check everything I touched paying special attention to the exhaust manifold and surrounding area. The new manifold came from the j/y and was barely used so I had initially just stuck with the O2 sensor that came with it; I changed this to the one the vehicle had previously been employing as it was not exhibiting these symptoms until after the job was done. I also double checked all the hoses, intake tube, wires and connectors; everything is connected.
From here, I research the method of pulling codes on OBD-1 vehicles by making the check engine light flash. It flashed a 111 and a 172 at the same time; the information I could find said the 111 means everything is normal, and the 172 suggested O2 or MAF. I am reasonably sure the O2 is not the problem so I focused on the MAF. Disconnecting it while running seemed to improve the way it idled so via the process of deduction, which also included the consideration of typical symptoms of MAF sensor failure, I proceeded to replacing the MAF sensor which amounted to little improvement.
At this moment in time the check engine light has not returned but it is clearly not in a drive-able state of being. It actually seems to have ever so slightly improved though.
Additionally, the symptoms only exist when the engine is hot and has been driven; it drives normally for 5-10 minutes until it gets to operating temperature then it starts to crap out. After changing the MAF sensor, I let it idle for 20 minutes and it was fine until about 2 minutes into the test drive.
Speculation - I am thinking spark plugs could also be a culprit as its has been forever since a tune-up but the sudden onset of this condition make me doubt this a little; it also has 8 plugs so even if one or two crapped out it should still run better than this I would think.
Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesFord Ranger / B-Series :: 1987 Truck Won't Start / Ignition Firing While Key On Engine Off
I've got an 87 ford ranger 4x4. The truck won't start. The ignition is firing off with the key on engine off. When I got the truck the transfer case was blown. The people I got the truck from drove it to here it sat. I check the wiring but the transfer case to make sure it diet get damaged causing a sort. When I got the pcm was missing. Took one out of a bronco 2 and changed the relays on the fender. Here what I've done so far
Relays
Pcm
Complete tune up.
Distributor and ignition module
Replaced and repair some grounds.
Ford Ranger / B-Series :: 1997 4.0L - 0 PSI Compression On 3 Cylinders
I've been fighting some issues with the truck and decided to do a compression test to decide if I want to try to keep 'Old Yeller' alive or not. I'm all for working on it until I have to dig into the lower end of the motor. I rented a compression tool and the results were a little shocking. I did this test with a slightly warm motor, fuel pump relay pulled, all spark plugs pulled and throttle @ 100 %. Motor turned over 10 times for each cylinder. I even moved all the rubber o-rings on the tool up on the threads to make sure I was getting a good seal.
Cyl 1 - 40
Cyl 2 - 0
Cyl 3 - 0
Cyl 4 - 80
Cyl 5 - 0
Cyl 6 - 60
Needless to say I didn't even bother doing this wet. My only real question is can this be close to accurate. I drive the truck daily. 160k mi on it.
I'm fighting the dreadful P0171 and P0174 codes and after a couple cycles I will get misfire codes. Its low on power (hard to keep @ 70MPH with some wind) and gets 10MPG right now. However it starts and runs and stays consistent (even though it rumbles like it has a nice cam in it).
Is it time to put Old Yeller down ? Are these compression results even remotely accurate ?
Ford Ranger / B-Series :: 2001 V6 Only Runs On 2 Or 3 Cylinders
My 2001 V6 Ford Ranger Edge has 124, 000 miles and always ran very well, Shortly after a minimal attempt to pull a vehicle out of a ditch the vehicle began to run poorly. This may be coincidental as problem did not begin straight away. The engine refused to start at first but now appears to run on 2 or 3 cylinders. I have checked AND CONFIRMED the following:
Spark at all cylinders
Fuel filter replaced
Fuel pump checked
Fuel pressure 56 psi at schrader valve on fuel rail
Fuel inertia cut off valve checked
E_Z start sprayed in feed horn did nothing
I hope to avoid towing it to the dealer,as I recently had a very negative experience doing this with the Honda dealer..
Ford Ranger / B-Series :: 1996 - Ignition Coil B Went Bad?
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesFord Ranger / B-Series :: 1988 - Power Loss Like Coil Getting Bad
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
Ford Ranger / B-Series :: 2003 - Multiple / Random Cylinders Misfiring
I have a 2003 ford ranger edge with the 3.0l engine. It started acting up today so i brought it to get checked because the check engine light came on. Three codes where pulled p0300, p0306, and p0313. They were multiple/random cylinders misfiring, cylinder 6 misfire, and first misfire at 1000 rpm. I have replaced the plugs and coil and still have the trouble.
View 5 RepliesFord Ranger / B-Series :: 2003 - Missing On 3 Cylinders Randomly / Lean Fuel
2003 Ranger (4.0 L-2wd)...
Codes - random misfire and cylinder banks 1, 2, 3, reads out lean fuel
Will be checking out injectors and rail pressure, however, trouble shooting in general for this issue.
Ford Ranger / B-Series :: Erratic Idle / Sporadic Miss / 3 Cylinders On Right Bank Dropping In And Out
Its a 1994 with 4.0, automatic, 4x4. Running fine, parked it, a week later I'm getting a bad but sporadic miss that according to the stealership is the 3 cylinders on the right bank dropping in and out. Driving down the road you can feel them drop out and when they come back its a kick in the pants like a turbo kicked in.
Shop says wires are good, plugs are good, and then lost me when they started talking around in circles and not making much sense.
What could make 3 cylinders all on the same side of the engine drop in and out? This wasn't anything that slowly came on. Fine one day, crap the next. The only thing I did prior to was replace the IAC because it was idling high, it was cruddy inside, and it looked like it was original. It was running fine after that till this issue popped up out of nowhere.
Mileage was claimed to be 178k but I'm beginning to suspect it's probably 278k.
Ford Ranger / B-Series :: Truck Sputters - Cylinders 2 / 3 And 4 Misfiring - Bank 1 And 2 Running Lean
I have a 99 ford ranger xlt 4.0 ohv basically it sputters so bad while driving it sounds like a dump truck but it all started when I changed my o2 sensors but in doing so I broke my heater control valve and when I was going down the road it started sputtering well it started sputtering so I checked the o2 sensors there good and I changed the heater control valve. But nothing so I changed my coil pack spark plugs and wires but still nothing. But on my reader it says cylinders 2,3, and 4 are misfiring and bank 1 and 2 are running lean plus it has a bad aroma of gas in the engine compartment but when it idles its somewhat smooth but when I'm driving it its horrible the sputtering is so bad it takes awhile to get up to speed plus I'm only getting 100 miles to a whole tank that's like 8 or 9 mpg I need to fix this soon. This is my only transportation...
View 11 Replies