Ford Ranger / B-Series :: Hub Spins On Driver Side But Tire Won't Engage

1987 ford ranger loaned it out and they said the hub spins on the driver side but the tire won't engage so it has no 4 wheel drive. Soon as I get it back hopefully today will know more.

View 14 Replies

Ford Ranger / B-Series :: 2002 - Tire Wear And Squeaking Front End

My '02 Ranger has had tire wear for a while now, and its on the inside of both front tires. I was thinking it was either toe or camber, or maybe both. I havent been able to get an alignment recently. If its the camber, should I get the camber kit from Ford?

As for the squeaking, it first happened last summer, and I sprayed WD-40 on the upper control arm bushing and it went away until last week (obvoiusly temporary). Now its back. Also happens while turning the front wheels.

View 10 Replies

Ford Ranger / B-Series :: 1990 XLT V6 - Loud Constant Whistle Sound On Driver Side

So I have a 1990 Ranger XLT 4x4, 2.9 v6. My issue is I am getting a loud constant whistle sound on the drivers side, just in front of the rear tire. It is not from the tire and it is a whistle not a whine. The truck is all stock nothing special. I do not have an exhaust anymore only a cat. Anyways the sound is constant an does not get louder or quieter while moving or in neutral it just stays the same. It just started in the last few days. Also the truck is a Manual.

View 3 Replies

Ford Ranger / B-Series :: 1996 XLT - Front Driver Side Spindle

I'm normally in the bullnose section, but recently started working on my father-in-law's 96 ford ranger. He wanted me to replace the front rotors.

I replaced the passenger side without a hitch, but when I went to replace the driver's side, I noticed the cotter pin and castle nut were missing. A nail was in the cotter pin's place. I backed off the spindle nut and found that the threads were eaten up, as was most of the spindle with various gouges and nicks.

1996 Ford Ranger XLT 2.3 ......

View 11 Replies

Ford Ranger / B-Series :: Constant Thud Coming From Front Driver Side While Driving

When driving down the road, there is a constant "thud thud thud" coming from the front driver's side of my 99 Ranger. I've been looking online for about two hours now, going back and forth to my truck to see if I can figure out the problem. All I've come up with is that it's the sway bar links. they're both disconnected, and I'm going to replace them anyway, but would that cause the constant thudding?

View 3 Replies

Ford Ranger / B-Series :: 2001 - Driver Side Front Brake Line Broken / Replacement

My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?

View 2 Replies

Mercury - Mountaineer :: 2002 - Loud Clicking Noise From Driver Side Front

2002 Mountaineer, suddenly started making a loud clicking noise driver side front. Seldom in reverse. Struts and axle look good, nothing hanging down.

View 3 Replies

Ford Ranger / B-Series :: Runs Rough - Driver Side Exhaust Manifold Cold / Passenger Side Hot?

1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.

Towed it home. This morning, started up OK but still running really rough.

While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.

Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.

This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?

View 4 Replies

Ford Ranger / B-Series :: Driver Side Headlight Go Out

I've got an 08' Ranger FX4. Recently I had the drivers-side headlight go out. Today I replaced the light, and while I was there, I decided to check every bulb on the truck. Everything else works, but I noticed the 2 factory "foglights" will not come on. This is a fairly recent development, because I use those lights quite often.

Even thought they don't cast a huge amount of light, here in the Vancouver area, winters are dark & rainy, so I think 4 points of light as opposed to 2 points is a benefit. To activate those lights, you pull on the headlight selector switch. Do those lights have their own dedicated circuit with fuse? Or does this sound like a switch problem?

View 14 Replies

Ford Excursion :: 2002 - Loud Bang When Applying Emergency Brake

2002 Excursion 4x4. While applying my emergency brake today I heard a loud bang. Now, the parking brake won't come up when I pull the parking brake release. Also, the noise is driving me crazy. Is there a way to release the pedal until I can get the cable replaced?

View 1 Replies

Ford Ranger / B-Series :: 1998 - Oil Leaking Somewhere On Driver Side

I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.

Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.

View 10 Replies

Ford Ranger / B-Series :: Burning Oil / Coolant In Cylinder 3 On Driver Side

I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.

I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.

The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?

If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.

This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.

View 9 Replies

Ford Ranger / B-Series :: 1990 V6 3 Cylinders On Driver Side Not Firing

Is there something that would make the 3 cylinders on the drivers side of a 1990 2.9l not fire? I have spark to the plugs and pressure/fuel at the schrader valve on the fuel rail. The passenger side cylinders are firing fine and the engine runs (roughly) on these 3 cylinders. Truck was running just fine, then all of a sudden, drivers side is dead. Is there a fuse or something that controls these three fuel injectors?

View 1 Replies

Ford Ranger / B-Series :: 2003 - In Every Few Seconds Chirping Noise On Driver Side?

I am a new owner of my first truck and it is a 2003 Ford Ranger 3.0L Extended Edge with 138,000 miles on it. I keep getting a chirping noise coming from driver side of truck. It only happens when I have the AC on. I can turn AC to just air and the chirping stops. This only happens when I am driving. If I have my truck parked in drive with the hood up, I go and turn on AC full blast and I hear no chirping. I can see AC compressor turn on a few seconds after I start the truck and it is not cycling on or off every few seconds as some people I have asked told me it should do. AC air is ice cold so I should have enough freon. Now this chirping is not constant like a machine gun going off but just about every 5 seconds or so it would chirp. I have heard of bad camshaft sensors causing chirping but would that happen every few seconds and only when you are driving down the road with the AC on? Now I have noticed when truck has sat for a long time I get belt squeal for a few seconds and it then goes away. I think the squeal goes away when AC compressor starts because I observed this when looking for this random chirp. Any clues?

View 4 Replies

Ford F-150 (2004-2008) :: Clicking Sound On The Driver Side Front Tire

I have a clicking sound on the driver side front tire. It only makes the noise when I am in motion and have the wheel turned. It does it reverse and forward. The CV axle is not turning, and it does it with 4x4 engaged and the cv axle turning. I had the front end apart not to long ago replacing the IWE Integrated wheel hub, and the bearing isn't to terrible old, and its a timken.

It didn't wobble when the wheel was up in the air, and seemed solid. All the other front end pieces have also been replaced. I also hear a rubbing noise when I am driving on that side. For awhile before I replaced my IWE Hub I thought it was the cv axle just turning ( I had the lined unplugged so it was engaged to prevent damage), well after fixing the IWE Hub it still makes the sound and the cv axle is not turning as it was before.

Wondering if the bearing is maybe on its way out? One thing I did notice is tie rod end I just replaced along with all my new front end parts (upper control arms, and lower ball joints) the boot is severed completely all the way around. However the tie rod appeared to be in good shape, just the boot has been cut or split some how. Which I plan to fix, but I don't see how that would cause a clicking sound. I have inspected to make sure no lines or vac hoses are rubbing, and they are not.

View 13 Replies

Ford Ranger / B-Series :: Vacuum Lines Bad On Driver Side / Actuators Won't Disengage Properly

I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.

Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).

View 1 Replies

Ford Ranger / B-Series :: 2003 - Clicking Noise From Driver Side Window / Will Not Roll Down

I have an 03 ranger and my driver side window will not roll down... My pass side rolls down just fine...when I push the down button all I get is a clicking noise out of what seems to be a little black box underneath the driver side dash and I can actually physically feel the clicking along with hearing it... When I push up on the button I get no noise or anything... this might be the motor...the regulator...or the actual switch?

View 1 Replies

Ford Ranger / B-Series :: 1957 - Driver Side Seat Reclining Mechanism Broke

I bought a set of Ranger seats for my 1957 Ford project. My question is the drivers side seat reclining mechanism is broke. I believe the seats are out of an STX or sport model, they have a slide out bolster and power lumbar and side bolsters.

Where to get a replacement mechanism. The mechanism works the handle is busted off. It is from an extra cab so the handle is a two way for the driver and or if anyone in the back wanted to use it. I think they may be from a 1992, only say this because I had one backin the day with these kind of seats.

View 4 Replies

Ford F-150 (2009-2014) :: 2011 2WD - Grinding Noise From Driver Side Front Tire

I have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.

Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?

View 9 Replies