Phaeton :: CEL Came On - Getting Error Coolant Temp Sensor High Voltage?
My CEL came on and the code said Coolant Temp Sensor High Voltage. Since there are 2 sensors, and my gauge isn't reading off, about 200F constantly, I assume the bad sensor is the water pump sensor. Also, is there a diagram of the sensorny locations and the easiest way to access them to swap them out. I have already purchased the sensor and gasket, just don't want to replace the wrong one or screw something else up in the process. It appears to be an easy job.
View 7 RepliesFord - Explorer :: 1993 V6 - Location Of Camshaft Sensor?
Does my 1993 ford explorer sport 4.0 L V6 engine have a camshaft sensor and if so where is it located?
View 2 RepliesPassat (B6) :: Radio Turning Randomly Off - Error Code Triggered By Low Voltage
I had this problem for a while. My radio is always on when I stop the engine in my 2008 Passat. But lately, the next day when I started the car the radio was sometimes off.
Well, apparently the random turn off was an indicator that my battery was slowly getting bad and not holding a full charge. Yesterday my engine light came on and when I took the car to the service department they found out that the error code was triggered by low voltage.
At the end, they changed the battery. This is the first time I am changing the battery on this car since I got it in 2008. So 5 years on single battery is pretty good I assume.
Santa FE SM (2001-06) :: 2005 - Code P1193 / MAF Sensor Low Voltage
I have a code reader got P1193 - MAF sensor low voltage
Is it shot or just need cleaning? Or is it something totally different
2005 Santa fe 3.5l
Lexus SC430 :: New Oxygen Sensor Reading Zero Voltage - Code P0430
Replaced my post cat drivers side O2 sensor tonight because I was getting zero voltage and a p0430 code. This is bank 2 sensor 1.
But I'm still reading zero voltage!! How could I still be getting zero voltage?? I checked the connections and they are firm. Checked every single fuse in car.
After my recent accident, the center console lights don't illuminate. My nav door doesn't close too. Could these all be related?? The connector for the O2 sensor is right next to the console, so maybe there is a loose connection or plug or perhaps a stray ground?? I do have wires all over the place in under the shifter bezel from aftermarket stuff..
Jeep - Grandcherokee :: 1998 - P0138 Code / O2 Sensor High Voltage
I drive a 1998 Jeep Grand Cherokee, 6 cylinder engine, with about 120,000 miles on it. I used a code scanner and pulled a P0138 code-bank 1 sensor 2 O2 sensor high voltage, if I'm correct. First of all, it looks like this sensor is after the catalytic converter, right? So I think I either have a bad 02 sensor or a bad catalytic converter. What are the consequences of driving around without fixing this? Will I see any reduction in fuel economy, or any potential long-term problems elsewhere?
View 2 RepliesFord - Explorer :: 2008 - Got Error Code P0401 With CEL?
I have a 2008 Sports Trac, with a 4.0 SOHC engine ... 165k miles. Last week my check engine (CE) light came on and the code is P0401 ... too little flow on the EGR system. I first tried cleaning the existing valve - but CE light still came on. So I replaced the old EGR valve, cleaned the SS tube from the exhaust manifold back to the EGR valve and the CE light is still on. I have not driven the truck since I replaced with the new valve ... only fired her up in the garage. Is this something that could possibly clear up given a couple of miles?
View 6 RepliesFord - Explorer :: 1997 - Airbag Error Code 45
I have a 97 Ford Explorer and the air bag indicator started to flash a code 45. What is this code and what do I need to do to clear this problem?
View 5 RepliesFord - Explorer :: 1996 - Airbag Error Code B1944
I just pulled error code B1944 from my 96 Explorer. It says
Crash sensor ground
Ckt 1, High res/open
I found the airbag diagnostic module (in passenger cowl area) and checked for loosed wire, nothing found. Where the loose ground wire is located? I checked under the seat (didn't do a through job, but looked).
Ford - Explorer :: Error Code For O2 Sensors Popped Up / Heater Circuits Gone Bad?
I have a '97 XLT, 5.0 and the error code for the O2 sensors has popped up, when checking it shows there isn't voltage for the heater circuits. I see there are 3 different heater circuits, 1ea for the left & right O2 sensors and a common one for the catalytic converter O2 sensors, so I ordered another PCM.
View 14 RepliesFord - Explorer :: Hard Jerk While Changing Into 2nd Gear - Error Code P0715
The other day, my Explorer gave a hard jerk while changing into 2 (maybe 3rd?) gear. Never happened before. I was under 20 MPH & had just stared it. (My speedometer works as do all the dials.) My Check Engine light came on & when I had the code pulled it read quote "P0715."Transmission Speed Sensor circuit condition. Vehicle speed above 15 MPH while transmission output shaft speed below 60 RPM. Possible cause Failed transmission speed sensor or electrical problem"
I got a Transmission Speed Sensor, (which I haven't put in yet), and was told that this would solve the problem. My question is twofold: Is there ANY chance this is a false or misread code and the problem is something else? And could ANOTHER sensor attached to the transmission be the cause? (How many sensors are on the tranny?) All I've read about this problem, say's replacing the Transmission Speed Sensor is preceded by the SPEEDOMETER quitting, but mine works fine.
The truck is a 1997 Explorer 4x4, but I don't use 4x4. In fact I've driven it without the forward drive shaft ever since I had the BW4405 Transfer Case replaced.
Camry :: O2 Sensor And Error Code P0137
Had my Check Engine light come on so I went by a local AutoZone to see if they could read the code. He said it was P0137, but what his reader can't tell is which one it is.
A co-worker pointed out where it was on my 2006 2.4, but I'm not sure if it's the sensor in the engine bay or the one closest to the catalytic converter. The engine bay looks easy to change out but I'm in no condition to be crawling around underneath.
Which sensor the P0137 is referring to?
Ford - Explorer :: 2002 XLT - O2 Sensor Replacement - Code PO136
My 02 Explorer (XLT, 4.0) decided to throw a new code today. PO136, O2 Sensor Circuit (Bank 1 Sensor 2).
While it may be a wire issue, I still plan to replace the sensor. So the question is;
Can I get to it from under the vehicle or is there an access panel under the console like on the 2nd gens?
I have the sensor on order and plan to get it done on my days off next week.
Lexus GX 2004-09 :: P0051 Error Code Calling For O2 Sensor
Got the p0051 error code and its calling for a o2 sensor. What brand does lexus use? I rather get one on line but dealer quality.
View 12 RepliesElantra XD (2001-06) :: Camshaft Sensor Error Code After Tune Up
I just had a ton of maintenance done on my 2003 Elantra. Spark plugs & wires, timing belt, drive belts, water pump, replaced coolant and replaced the transmission fluid. The spark plugs are NGK platinum as recommended in my handbook. As soon as the mechanic started the car after the tuneup, the engine light came on with a cam shaft sensor code. He said it went off on its own.
The engine light came back on when I started the car. There's also a major loss of power after coming to a stop. I have to floor it to get it to go anywhere above 20 mph after a stop.
The mechanic said that when he replaced my water pump the liquid splashed all over everything and he thinks he might have gotten something wet that shouldn't have gotten wet and that all will be fine after it dries.
Santa Fe (CM - 2007-12) :: Error Code P0057 - O2 Sensor Replacement
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
Passat (B5) :: Getting Error Code P3081 - Coolant Temp Sensor?
P3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 RepliesFord Ranger / B-Series :: 1993 - Getting 157 / 158 And 159 Codes - Mass Air Flow Voltage?
Truck is a 1993 ranger 4.0 ohv
Ok I have been getting 157, 158, and 159 codes. I have cleaned and replaced the MAF with no success. I checked the voltage to the sensor 12v, checked the voltage from the signal wire and it is to high. It has been high on the cleaned unit and on both replacements, so I am thinking it is not the MAF, but what will cause it to register high. I cant get the signal voltage below 1.9V at idle.
Signal also reads high with the ignition on and the engine off. What would cause the voltage to be high, I have read it could be an IAC but I would think that would not effect it with the engine off.
Explorer :: 2000 - Pulled Over Error Code PO172
My daughters 2000 explorer has a PO172 code, tune it up,Replaced filters plugs & wires and rear O2 sensors that were damaged. Has 65 psi on fuel rail. Can not find any vacuum leaks. Not sure maybe injectors are dirty.
Also I replaced MAF, now it idles, But it's a rough Idle,Gets worse in gear. She say's on cold start up she can smell a whiff of gas ..