Ford - Explorer :: 1996 - Airbag Error Code B1944
I just pulled error code B1944 from my 96 Explorer. It says
Crash sensor ground
Ckt 1, High res/open
I found the airbag diagnostic module (in passenger cowl area) and checked for loosed wire, nothing found. Where the loose ground wire is located? I checked under the seat (didn't do a through job, but looked).
Ford F-150 - 1997-2003 :: 2001 SuperCab - Airbag Error Code 2-7 Flashes On Startup
I'm getting an error code 2-7 (flashes two times, pauses, then flashes seven times) when my truck starts up. It does this cycle twice then stays on permanently. It has only started doing this since last night when I replaced my factory tape deck with a factory Cd player from a 2002 F-150.
View 14 RepliesFord F-150 - 1997-2003 :: Airbag Light Flashing 5 Times Then 2 Times - Error Code 52
I had been having battery issues with my 97 ford f150 4.6 liter for the longest time, thought i had a short under dash, i pulled entire dash out, disconnecting bat first of course, and inspected all wiring harness connections and fixing my issues and putting it all back together. now with new bat and all put back together i am now getting the airbag light flashing 5 times then 2 times (error code 52) i know it has some thing to do with power failure or backup battery, but now with the new battery in i cant seem to get it to reset. How to do this?
View 3 RepliesFord Escape / Hybrid :: 2003 - Airbag Light Error Code 21
Well, I bought a used 2003 Escape for my daughter and without thoroughly researching the airbag light, now have a problem. The light flashes twice, pause, then once, so I think this is error code 21? I cannot find anything on what this code is and how to fix it. I disconnected battery for an hour and now I get 4 flashes, pause, 6 flashes, 46 error.
View 1 RepliesGolf IV R32 :: Airbag Light Went On - Error Code 00592
My airbag light went on so i scanned for codes and I got:
00592-seatbelt switch:right (e25) 32-00-resistance too high.
What I need to do to fix this and make the light go away?
Ford - Explorer :: 2008 - Got Error Code P0401 With CEL?
I have a 2008 Sports Trac, with a 4.0 SOHC engine ... 165k miles. Last week my check engine (CE) light came on and the code is P0401 ... too little flow on the EGR system. I first tried cleaning the existing valve - but CE light still came on. So I replaced the old EGR valve, cleaned the SS tube from the exhaust manifold back to the EGR valve and the CE light is still on. I have not driven the truck since I replaced with the new valve ... only fired her up in the garage. Is this something that could possibly clear up given a couple of miles?
View 6 RepliesFord - Explorer :: 2004 - Airbag Code 33 - Driver Or Passenger Side?
Is the code model AND year specific? I have a 2004 Explorer. Can clear this up? I already cleaned the yellow connectors under both seats and I still have the LFC. I have started the truck 3 times since then and cycled the key about 6 times to see if it would clear. I got a rejection sticker today and need to fix it ASAP.
View 14 RepliesFord - Explorer :: 1993 - Error Code For A Low Voltage MAF Sensor
1993 ford explorer sport... I got an error code for a low voltage MAF sensor. how would i go about fixing it? Do i need to get a new MAF sensor?
View 1 RepliesFord - Explorer :: Error Code For O2 Sensors Popped Up / Heater Circuits Gone Bad?
I have a '97 XLT, 5.0 and the error code for the O2 sensors has popped up, when checking it shows there isn't voltage for the heater circuits. I see there are 3 different heater circuits, 1ea for the left & right O2 sensors and a common one for the catalytic converter O2 sensors, so I ordered another PCM.
View 14 RepliesFord - Explorer :: Hard Jerk While Changing Into 2nd Gear - Error Code P0715
The other day, my Explorer gave a hard jerk while changing into 2 (maybe 3rd?) gear. Never happened before. I was under 20 MPH & had just stared it. (My speedometer works as do all the dials.) My Check Engine light came on & when I had the code pulled it read quote "P0715."Transmission Speed Sensor circuit condition. Vehicle speed above 15 MPH while transmission output shaft speed below 60 RPM. Possible cause Failed transmission speed sensor or electrical problem"
I got a Transmission Speed Sensor, (which I haven't put in yet), and was told that this would solve the problem. My question is twofold: Is there ANY chance this is a false or misread code and the problem is something else? And could ANOTHER sensor attached to the transmission be the cause? (How many sensors are on the tranny?) All I've read about this problem, say's replacing the Transmission Speed Sensor is preceded by the SPEEDOMETER quitting, but mine works fine.
The truck is a 1997 Explorer 4x4, but I don't use 4x4. In fact I've driven it without the forward drive shaft ever since I had the BW4405 Transfer Case replaced.
Ford F-150 - 1997-2003 :: Airbag Code 33 - PAD Light Is Still Functional
1997 F150 - Getting an airbag code 33. PAD light is still functional. Some googling suggests a sensor in the passenger seat belt but I think mine is too old for that.
View 3 RepliesFord F-150 - 1997-2003 :: CEL On With Error Code P0155?
Have this code Po155 oxy sensor heated bank 2 sen 1. I have replaced all sensor in the tail pips and check engine light code still comes on.
View 7 RepliesExplorer :: 2000 - Pulled Over Error Code PO172
My daughters 2000 explorer has a PO172 code, tune it up,Replaced filters plugs & wires and rear O2 sensors that were damaged. Has 65 psi on fuel rail. Can not find any vacuum leaks. Not sure maybe injectors are dirty.
Also I replaced MAF, now it idles, But it's a rough Idle,Gets worse in gear. She say's on cold start up she can smell a whiff of gas ..
Ford F-150 - 1997-2003 :: 2002 - Airbag Light Blinking - Code Reads 27
Looking to see how to repair my blinking light. Code reads a 27, most what I've read says it's a PAD light, which this truck does not have. It has been in an accident, both airbags deployed. Since then both seat belts & bags have been replaced, nothing else.
View 7 RepliesFord F-150 - 1997-2003 :: IAC Over Speed Error Code P1506
About 3 days ago I noticed my engine RPM was around 250 higher than usual. Usually my truck idles around 550-600 rpm (I know this is low). Anyway, yesterday it threw the P1506 "IAC over Speed Error" Code. It is idling very rough, shifting weird, but does crank up fine.
My truck is now at 93,000 miles and I just cleaned the IAC at 87,000 miles due to the common no start condition. I guess I am going to get a new IAC now since another code came up.
Well, my question is it came up with two other codes also:
P0171 - System too Lean, Bank No. 1
P0174 - System too Lean, Bank No. 2
Do you think the P1506 (IAC Code) made the O2 Sensor codes show up or is it really the O2 Sensors? I just changed my two upstream O2 Sensors around 90,000 miles. Should I get a new IAC or try to clean it again?
Ford F-150 - 1997-2003 :: 2002 - Got Error Code PO174
Looking for some experience/recommendations for the "what to do" and "in what order" for an error code. Recently the "SERVICE ENGINE SOON" light came on and has stayed on for the last 2 weeks. It has don this before after a heavy rain but went off after a few days but not this time. I took it to Advance Auto who hooked it up to a Trouble Code Reader and got back "PO174- Bank 2 system to lean". From what I've read from the Haynes book and other forum postings this is either a O2 sensor issue or a intake manifold gasket issue? Does this sound right? Next is how to go about addressing this issue in a systematic manner so as not "fix" 10 things that don't need fixing and not running to mechanic and paying a buttload for something I can do myself for less.
View 1 RepliesFord/Mustang :: 1997 - Getting Error Code P0304 / Cylinder 4 Misfire
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
Ford F-150 - 1997-2003 :: Got Error Code P1000 - Idle Rough - CEL On?
What that means? The check engine light is NOT on but I looked for a code because my truck is idling rough, and when driving, when the overdrive kicks in, it vibrates really bad. As if a bad U-joint on your drive shaft. The truck has been in a field for about 5 months broke down so any clue? Haynes manual says nothing about P1000.
View 13 RepliesFord F-150 - 1997-2003 :: 1999 - IAC Over Speed Error Code P1506
1999 F150 4.2L 125K miles.... My problems started about a month ago. I had a P1506 error. The engine was running fine but received the error code. I replaced the IAC and the air filter. Engine still running fine. A week later I received a code for the Intake Air Temp Sensor (don't remember the code). The engine still running great. I bought a new Air Temp Sensor and noticed the wires from the Air Temp Sensor were rubbing against the belt and had been severed. I made a mistake when replacing the air filter of not checking the wires (confession is good right).
The engine also constantly ran a fast idle 2000 to 2500 at this time. I repaired the wires. The engine light went off and idle now starts great and smooth but when heats up will will go to 2000-2500. I then decided to replace the Air Temp Sensor hoping to fix idle problem. Engine still idle fast when warm. However, when I come to a stop and put in neutral the engine will take a minute but go down to normal idle after sitting. Engine light stayed off for a week. Now engine light back on with original code P1506. Idle is still not working correctly.
I feel like I made it worse than it was originally and not sure what to try next.