Santa FE SM (2001-06) :: 2005 - Code P0463 / Fuel Level Sensor?
I know the code is fuel level sensor, but i can't find the parts online. nothing comes up with the part name fuel level sensor. What is the part number for this or the number for kit because i believe there are 2 sensors?
View 1 RepliesSanta FE SM (2001-06) :: P1192 Code - Faulty TPS Sensor
My 2003 Santa Fe 3.5 is in limp mode, you can't change the gears and showing signs of faulty tps sensor, but my mechanic is telling me to change whole electronic throttle system , May be its only the sensor.
View 1 RepliesSanta FE SM (2001-06) :: Code P0325 Knock Sensor
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 RepliesSanta FE SM (2001-06) :: P0103 Engine Light Code For MAF Sensor
I have an 2004 Santa Fe and im having some Mass Air Flow Sensor problems but I dont know what's wrong. My engine light came on for the second time after awhile. And I got it checked for the code and of course it was my sensor again. The first time I just giggled it around and the light went off. I did the same thing today with giggling it again went off. So I feel like it might be a loose connection but I really hope it isn't failing because im pretty sure that's uber expensive to fix.
View 2 RepliesSanta FE SM (2001-06) :: Code P0340 Cam Shaft Sensor Fault
I have a 2005 crdi diesel santa fe that i have a strange problem with it starts up first time no problem in the mornings and can drive all day long. However if i switch it off and leave it sit for about a half hour no way will it start again until it cools off. It will start though with a push start instantly!
I got only one fault code P0340 cam shaft sensor fault, i replaces sensor and made no difference. Is this a common fault???
Santa FE SM (2001-06) :: 2004 - CEL Code P0720 / Bad Output Sensor
My hyundai 2004 sta fe awd 3.5 LX engine light came on while cruising dwn the freeway. At the same same time i heard a loud thud and speed went down from 65 to 40mph and a high idle. I drove it home and hook up the obd2 scanner and got P0720 suggesting bad output sensor. So I decided to buy new sensor from the dealership, put it in and thought it will fix the problem. After few days the engine light came on (P0720)again with the same clunk noise and speed down from 65 to to 40 mph at high rpm. Took it home, did some experiment by putting back the old sensor. I Connected the harness back, but this time I wrap the female connector with the electrical rubber tape and electrical vinyl tape. Problem fixed. No more engine light,transmission shift smoothly. I think the connector (harness side) to the output sensor was crack that's why its not making good solid connection. The rubber tape technique held the female connector pins tightly together. New part didn't do anything but it was a learning experience.
View 1 RepliesSanta FE SM (2001-06) :: CEL On / Code P0107 - MAP Sensor Circuit Low Input
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 RepliesFord - Explorer :: 1993 - Error Code For A Low Voltage MAF Sensor
1993 ford explorer sport... I got an error code for a low voltage MAF sensor. how would i go about fixing it? Do i need to get a new MAF sensor?
View 1 RepliesSanta FE SM (2001-06) :: Code P0715 - Input Speed Sensor Location?
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 RepliesSanta FE SM (2001-06) :: Code P2125 - Throttle Position Sensor Replacement?
Getting code P2125. Read on here to get some electric contact cleaner and see if that works by cleaning the connections.
If I do end up changing out the Throttle Position Sensor, what voltage value do I look for when installing the new one ?
Lexus SC430 :: New Oxygen Sensor Reading Zero Voltage - Code P0430
Replaced my post cat drivers side O2 sensor tonight because I was getting zero voltage and a p0430 code. This is bank 2 sensor 1.
But I'm still reading zero voltage!! How could I still be getting zero voltage?? I checked the connections and they are firm. Checked every single fuse in car.
After my recent accident, the center console lights don't illuminate. My nav door doesn't close too. Could these all be related?? The connector for the O2 sensor is right next to the console, so maybe there is a loose connection or plug or perhaps a stray ground?? I do have wires all over the place in under the shifter bezel from aftermarket stuff..
Jeep - Grandcherokee :: 1998 - P0138 Code / O2 Sensor High Voltage
I drive a 1998 Jeep Grand Cherokee, 6 cylinder engine, with about 120,000 miles on it. I used a code scanner and pulled a P0138 code-bank 1 sensor 2 O2 sensor high voltage, if I'm correct. First of all, it looks like this sensor is after the catalytic converter, right? So I think I either have a bad 02 sensor or a bad catalytic converter. What are the consequences of driving around without fixing this? Will I see any reduction in fuel economy, or any potential long-term problems elsewhere?
View 2 RepliesSanta FE SM (2001-06) :: Taking Multiple Tries To Start - P0340 Camshaft Position Sensor Circuit Code
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
Caravan/Voyager :: 2005 Town Country - P0032 Oxygen Sensor Heater Circuit High Voltage
P0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
Santa FE SM (2001-06) :: 2005 - P0113 Code After Spark Plugs And Coils Replacement
Just replaced the spark plugs and coils yesterday, today it gives P0113 code, Intake air temperature (IAT) sensor - high input Wiring open circuit/short to positive, ground wire defective, IAT sensor, ECM...
View 3 RepliesElantra XD (2001-06) :: Check Engine Code P0010 / ECM Has Detected Low Voltage On VCT Circuit
AutoZone provided this code for my check engine light: P0010.
Definition: Intake camshaft position actuator circuit open
Explanation: ECM has detected a low voltage on the VCT circuit
Probable Cause: 1) Open or short circuit condition on the VCT circuit; 2) failed VCT solenoid
Is there a part I can replace myself that can fix this, or is this a dealer repair?
Prius (2001-03) :: Warning Symbols Come On Frequently - P3000 Code / High Voltage Leak
I bought an 03 with 58K miles on it. shortly after I bought it the check main battery light came on, after the local Toyota dealer told me I needed a new main battery. I had a P3000 code, a high voltage leak. It turned out to be corroded buss bars and cables, with 2 leaking cells, $1,450.00 latter the onboard computer said the problem was fixed and my display read normally for about 1,500 miles before I started getting that code and the check main battery light again.
I took it back to the shop tat did the work and they ran the diagnostics on it again, checking the main power cables that led from the main battery under the car to the Toyota Hybrid system, inverter? Under the hood they checked all of the high voltage connections, they all checked out fine. The shop then took several days to do an online search for possible causes. This led to the CV trans axle with its electric motors and generators as the possible culprit. The car is running and driving fine, so I did the 60,000 mile transmission oil change, suggested by my mechanic ( apparently the fluid becomes conductive with age) the check battery light will go off if I remove the secondary battery terminal for a minute or so and stayed off for 2 tanks of gas after the fluid change but it did come back on.
I can reset the computer easily enough and it will stay off for 3 to 400 miles but I'm looking to get the damn light to stay off. I'm going to change the trans fluid again. Changing the drive motor or generator?, can this be done in the car? or at all? It may be that if this is the problem it may end up making sense to just put in a new CV transaxle.
Santa Fe (CM - 2007-12) :: Error Code P0057 - O2 Sensor Replacement
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
Santa Fe (CM - 2007-12) :: 2011 - PO198 Code / Oil Temperature Sensor?
I took my 2011 Santa Fe, 3.5 liter, in for the tail light water thing, and a cracked fitting down near the thermostat (all warranty). I bought a rad flush while they were in there.
I picked up the car, drove for 1/2 hour and got a CEL. Plugged in my code reader and got three PO198's, oil temperature sensor. The dealer was closed by then, so I left it in their lot and will call them tomorrow. Their repair performance to date has been poor, and that's being polite. How a rad flush could cause a PO198? Could they have forgot to plug the sensor in? Is it located anywhere near the thermostat housing? Did they not get the air out of the rad, and maybe the engine did get hot?