Ford 6.0L Power Stroke Diesel :: Dead Pedal / Truck Went To Idle And Would Not Respond
Had 3 separate episodes dead pedal on my 04 bone stock 6.0. About a week ago I pulled out on the road and the truck went to idle and would not respond no matter how much throttle I gave. After about 10 seconds it woke up and took off. Had this happen 2 more times this afternoon.
No codes or dash lights.... What this might be? I have a 500 mile road trip this weekend and am worried about being stranded on the side of the road.
Ford 7.3L Power Stroke (1999-2003) :: Bump / Thump Type Noise When Start From A Dead Stop
For probably years, I have had a bump, thump type noise when I start from a dead stop... say at a red light. I had it in my head, maybe there was that much slop in the drive train... as old truck is over 400,000 miles.
Yesterday, I rebuilt the driver's side axle, bearing,seals, new hub...the works.. I heard that noise again later... and my thoughts were, I did all that work and I'm going to find a lower/upper ball joint is bad, although I did look at them and thought they were fine during the rebuild.
Had my wife get in truck.... and swing wheel back & forth... so maybe I could see what was loose.. or making noise.
I was shocked... just something I never thought of looking at. The u-bolts holding the leaf springs were loose... the whole axle was shifting back and forth on the axle. I've never touched those bolts....
Ford 7.3L Power Stroke (1999-2003) :: Truck Dies When It Comes To Stop
I know there are a few threads floating around regarding truck dieing, but mine is slightly different than the others, maybe its the same culprit, maybe not, but i thought i would start a new thread just in case.
First, I commute about 50 miles to work everyday, truck gets plenty of interstate highway run time, smooth as silk. About a month and half ago when i almost got to work I slowed to stop at a red light. As I came to a stop the truck "stumbled". Acted like it wanted to die but caught itself and kept going. I said whooaaaa girl, what this? Ive had this truck for almost 10 yrs now and never anything like this. About a week or so later, same commute, same red light, cept this time it dies. Starts right back up no problem. Just acted like someone turned the key off.
Then a week or so after that, while driving home this time, as I pulled up at the house to check the mail at the mailbox, when i came to a stop it died. Cranked right back up. Before I could put in drive, it died again. Cranked right back up and i drove on into the driveway. Then a few days later, while checking the mail again, it died again. Cranked up immediately and parked.
Today, while driving home, after i had gotten back to town, but before i got home i made a stop at bank drive thru, when i came to a stop, it died. While cranking it wanted to start and kind of stumbled on itself and died. Then it cranked right up and i came on home no problem.
So far it only occurs after approx 45min to 1 hr of operating time so the engine and everything else are at temp and far from cold. After reading thru some of the other threads of similar but different conditions (cold start dieing, dieing while under power, etc) Im getting flooded with ideas of what could cause it, but not settled on any.
1.Could be failing ICP? (original, has never been changed, 317k+).
2.Could be plugged fuel filters? (been a while since changing, approx 30k+)
3.Could related to one of my own earlier threads regarding possible failing alternator (when rpms drop can volts drop enough to kill engine?)
4.Could be loose ignition switch? (about 2 yrs ago i had to swap the blinker switch, to get to it had to remove the ignition. Upon re-installation the switch never did get tight as before and was loose. Been loose ever since. To the point that with key out of ignition and door ajar i will get the door chime as if the key was in ignition. I can bump the ignition, and chime goes away. Been this way for two years and no apparent problems. Until now maybe?)
I was thinking ICP after a few of the other threads, but after tonight Im leaning towards the ignition switch. I guess i can try to wiggle the switch after cranking tomorrow and see what that does for a trouble shooting effort. Is there a way to trouble shoot the ICP to see if its failing or not? Isn't that a fairly costly sensor? Would hate to buy one and not be the cause, but after 317k i may need to buy before too long anyway.
Ford Super Duty (1999-2016) :: Dead Space Area When Push The Brake Pedal Forward
My question is this...when my foot makes contact with the brake pedal there is about a quarter or half inch of "space" where I can push the pedal forward before you can feel whatever the pedal pushes against make contact and begin applying braking.
This dead space area will always activate the brake lighting but until you reach that next part under the dash somewhere no braking occurs.
I am quite used to driving my 2010 and this doesn't occur....can not remember if the 99 has always done that and i just realized it or if this is a new issue.
Brakes and stops great with and without load. No issues otherwise. Pedal pops out quickly and normally when taking your foot off.
Ford 7.3L Power Stroke (1999-2003) :: Truck Will Accelerate Quickly With Slightest Touch Of Gas Pedal - Service Engine Soon Light On
So about 3-4 times per day, my truck will accelerate very quickly with the slightest touch of the gas pedal, then followed by the service engine soon light...I checked for any codes to see what I may need to fix, but no codes are found.
What this could be? I am also having issues to where I a few times per day I have to put my truck in neutral to get it to start instead of in park...could the two be related?
Ford Super Duty (1999-2016) :: 2003 F250 - Brakes Pedal Hard - Truck Doesn't Stop Well
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: When Push The Clutch To Floor Its Not Disengaging All The Way
In my 99 with a zf6 it seems like when I push the clutch to the floor it's not disengaging all the way. It has a newer valair clutch in it maybe 15000 miles on it. It's really hard to get the truck in reverse or first from a stop. If the truck is stopped and it's in reverse or first with the clutch to the floor it will move in that gear. Is there a adjustment on the clutch? I'm thinking no since its hydraulic....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Truck Would Die While Driving The Truck
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: No Power / One Bank Dead
I have a few codes I pulled with and AE Using CCT and I got codes PO263, P0269, PO275..
Also got P0603, P1316, P0470 on power train
Did a BUZZ TEST P0273 and also check uvc harness
I've replaced ICP,OIL and Filter,fuel filter,CPS still no luck.
Ford 6.0L Power Stroke Diesel :: 2004 - Dead Pedal Every Now And Then
Recently I have been experiencing dead pedal every now and again, but it eventually comes back. Its happened on the interstate a couple of times and that can get pretty dangerous. Now I am having issues with a no start condition out of no where. It will eventually crank but it churns and churns for a VERY long time, like 15- 30 mins before it will fire again. This has happened twice now. Here are the codes I pulled from Torque:
P0263
P0281
P0299
P0528
Where this is all coming from? I thought at first bad TPS on the adjustable pedals, but now with the no start condition, could it be fuel pump related? Yesterday I was at the dump and it was idling, then got real erratic and shut down. Then wouldn't start for 20 minutes.
Golf/GTI VI :: Accelerator Dead Zone - When Press Pedal From Dead Stop Nothing Happens
So what I might have thought to be a transmission lag may be actually a dead zone in the pedal. When pressing the pedal from dead stop nothing happens until you press the pedal down further. Any way to reduce that or eliminate?
I'm referring to NA 2.5L engine with auto trans.
Ford 6.0L Power Stroke Diesel :: Brake Pedal Dead - No Boost For Power Steering - Hose Leaking?
Is there one thing that when broken makes both the steering and brakes lose all power? Does the power steering and hydroboost share a pressure source?
My brake pedal is dead and I get no steering boost, but the master cylinder and PSP are full of fluid. Do I replace both, or replace one first to see if that fixes both? Or could it just be a hose leaking? Not sure how to diagnose this one.
Ford F-150 - 1997-2003 :: 1999 - Idle Hangs When Push The Clutch In While Coming To A Stop
I have a 1999 f-150 4x4 4.6 5spd manual 180,000 miles on the clock. My question is, when coming to a stop i push the clutch in an the idle hangs at about twice what it should be until i come to a complete stop then it drops to normal. It's not like somethings sticking cause it will stay at the high idle as long as were rolling but as soon as the wheels stop turning it drops down.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Changed Intercooler Boots Still Poor Boost - Turbo Dead?
ive noticed my boost has been going down lately. At first I thought it was a boost leak so I replaced all the intercooler boots and both sides of the intercooler pipes. That diddnt change anything at all. I recently got new injectors (200/30%) and a hydra tune for them and it was quick the first few days i was running with that setup, my boost has been dropping and currently at WOT I can't even get to 10lbs of boost and it is noticeable driving, it's slower than it was stock. There was no play in the shaft of my turbo and the turbo in there is only 2 years old. Could the turbo be bad already? Or is there anything else I can check before buying a new one. I have an upgraded hpop and the 6637 intake.
View 13 RepliesFord 6.7L Power Stroke Diesel :: 2014 - Hesitates From Dead Stop?
I have a 2014 F250 with the 3.55 rear end and 6500 miles and since new it has a hesitation from a dead stop that I cannot determine if it is normal or not. I took it into a dealer that specializes in diesels and they drove it and told me it is normal. Every time I see someone with the 6.7 I ask them if they have the same problem and I get all kinds of explanations from turbo lag to protecting the tranny. The hesitation I feel is when I throttle from a dead stop. It is a very slight hesitation, but very noticeable, almost like a little "dead spot." If I take my foot off the brake and let it take off on its own for just a second or two and then throttle smoothly it is not there at all. If this is not normal, I want to do everything I can to get it fixed. It is driving me nuts.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Won't Go Over 45 MPH
I have a 2003 7.3. Suddenly a week ago when I left work, I noticed my truck wasn't picking up much, but i was in a 40mph zone. I then jumped on the freeway and noticed the truck would not go over 60mph. Once I exited and got on another road with a 55mph speed limit, the truck would not go over 45mph, I had the pedal pressed all the way down and would not go over 2000 rpms. Also, for the transmission to shift, I would have to let off the accelerator.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: No Power - Truck Will Crank For About 15 - 20 Seconds Before Turning Over
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
Ford 7.3L Power Stroke (1999-2003) :: Truck Wouldn't Go Fast / Plenty Of Power In Low End
2002 f250 7.3l diesel...
I got a new radiator and the tranny fluid was the worst the mechanic had ever seen. He serviced it and warned me that it might not be long for this world. I broke my flexplate and so I had to pull the tranny, and I decided to throw a new torque converter in because it was giving g me symptoms like a broken sprag( it wouldn't rev up or do a brake stand in gear, therefore slow takeoffs).
I was recommended to replace the tranny, I decided I could do the job again down the road if I needed to. About two thousand miles down the road I had a hard shift going from overdrive down to get up a hill and about 10 miles later the truck started slowing down....I couldn't give it enough pedal to keep it going and the engine sounded rough.
I pulled over and checked fluids and everything was fine, truck idled fine, bright red tranny fluid not burnt at all. Pulled on to the road again and it pulled fine until about 40 mph and it wouldn't go any faster. I got it towed home and ordered up a tranny from Ford figuring it must be toast, but I thought I'd throw it out to the forum to see if there is any other troubleshooting I can do before I install the new one in case it is some other problem or some electrical harness or something, or if that is a pretty standard reaction to a fried tranny.
Engine runs good at idle, shifts perfectly to drive and reverse, drives forward and back(I'm very hesitant to drive it out of the driveway in case I can't get it back in). Only happened two times before I decided to tow it. Temps looked fine on the gauges, fluid was a little overfilled in the tranny, but again, not hot or burnt.
Ford 7.3L Power Stroke (1999-2003) :: Truck Would Stumble And Lose Power / Idles But Won't Rev Up
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.