Ford 6.0L Power Stroke Diesel :: 2003 F250 Truck Just Died While Driving
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Possible To Add A/C To F250 Truck?
So long story short I have a 99 f250 xl, 7.3 130k. Overall good truck but has no options, never had AC but would like to add it. I have seen the kits on bought4less. So I'm thinking all the factory parts should be bolt on, since the holes should be all there, and since most of the wiring should be there. I just need to collect all the parts. Also one question I have is, what goes through the firewall. Is it just the lines, or how does the ac get to the vents? Dumb question but don't get that part of it.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Truck Ran Fine Now Won't Start
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Will Die For No Reason
01 f250. Just bought from my brother. 140000 miles. Immaculate. Truck will die for no reason. Running down the highway, or sitting at a red light. Fires back up. Sometimes have to crank a few times. He has had at a mechanic and everything checks out good. Since birth its only had royal purple that he has changed every 5000 miles as well as all filters. Where do I start?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Won't Start
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
Ford 7.3L Power Stroke (1999-2003) :: Truck Was Shutting Off While Driving
Last week the engine in my truck was shutting off while driving. Happened to me 3 times over the course of two days. The first couple of times, the engine was dead for 3-5 seconds and then the engine would come alive and drive normally again. The third time was about a 10 second event...same result, engine refired on it's own and drove normally. I was in motion all three times so the engine restarts all occurred before I was able to bring the truck to a complete stop.
No check engine light...(I didn't pull any codes because I didn't have my laptop with me). So, I decided to try a new CPS. I had one in my glove box since 2003 so in it went. It replaced a black CPS that I purchased from Riffraff about 100k miles ago. The new CPS seems to have done the trick. I've driven about 500 miles since the swap and the symptom has not returned. I wonder how long this one will last. It's a Ford replacement part so maybe I'll get another 100k miles...
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Truck Died And Will Not Restart
Another "no start" issue... The details:
- 2002 F250 7.3L
- Rosewood stage two single shot injectors (rebuilt 1 week ago).
- DP Tuner
- Brand new OEM IPR
- ICP about two months old (OEM)
- New UVH's installed about a month ago
The issue: After installing the injectors and driving about 30 miles the truck died and will not restart. Had to have it towed home. Thus far, I've unplugged the ICP, switched out the CPS with a known good, replaced the IPR, checked the hpop simply by removing the fill plug on the top of the reservoir and gave it a quick crank - oil definitely came pouring out, removed valve covers and plugs to verify oil in the high pressure rails. Oil dummy gauge climbs after about 5 seconds of cranking and seems to hold.
Hoping it's not an injector failure as I just had these reworked. EDIT: Forgot to mention, not seeing any white smoke while cranking. Fuel bowl, full of fuel and fuel pump was replaced this past spring. What to check next? Tried taking a snapshot from a video to show the readings. The ICP seems low, and when unplugged shoots up the 2500, but still no start.
Ford 7.3L Power Stroke (1999-2003) :: Truck Died While Driving Almost Like Ran Out Of Fuel
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
Ford 7.3L Power Stroke (1999-2003) :: Truck Cut Out Twice While Driving - Code P1211
My wife returned home and stated that my excursion stopped running twice while she was driving it. She said both times were as she was letting off the throttle coming downhill an off ramp. Both times it fired right up and drove away fine.
I pulled the codes using torque app and it showed a p1211. Unfortunately I had just screwed up my gauge settings so I really didn't have any gauges set up so I couldn't use it. (It's for the 6.0 anyway).
After some Internet searching I am guessing it's an issue with the icp or ipr. How do I tell which one to replace? Truck does have a dp tuner normally set to 80 economy tune.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Jumps When First Step On Brakes
Tires have less than 10,000 miles on them, and air pressure is within 2 lbs left to right side.
New calipers.
New soft lines.
New hard lines.
New pads.
New rotors.
New ball joints.
New tie rod ends and center link.
New front axle universals.
Brake fluid and all other parts are less than 6 months old. I can let go of the wheel and the truck tracks straight, 10mph to 100 mph. Whether I am going 10 mph, or 100 mph, when i first step on the brakes the truck jumps right. Needless to say, the faster i am going, the worse it jumps.
After first brake application, truck tracks straight. Let go of the wheel and it tracks straight from 100mph to a dead stop with brakes applied after the initial jump. Whether I am hard on the brakes or gentle, it does not pull at all. Only on the initial step on the brakes.I am at a loss as to what the heck is wrong with it.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Has Always Had Difficulty Starting Cold
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Battery Light On When Truck Is Running At Less Than About 1200 RPM
Battery light comes on when the truck is running at less than about 1200rpm, but I see zero movement on the needle. Weird thing is i charged the batteries and tested the alternator with my multimeter and it was reading 14.1-14.2 which is nominal. Run it for about 10 min then it reads 12.3-12.8
I'm thinking a bad cell in the battery or alternator is going out. Oh and all the connections are tight, wires look good. 2001 f250 4wd 7.3 intake exhaust basic tuner gauges. Could the constant heat be a factor?
Ford 7.3L Power Stroke (1999-2003) :: Truck Stalling While Driving / Dies For A Second On Accelerating Or Cruising
Like the title says my truck has been stalling while driving. Accelerating or cruising it dies for a second, two at the most, and then just keeps chugging along again.
I thought i'd fixed the problem last year when I did injector O-rings and 50 cented my UVCH. It hadn't done it since, until two days ago. Started out with a two good solid stalls while gently accelerating up hill. I had thought maybe my fuel pickup foot had finely given up the ghost because I was below a quarter tank. But I filled her up full, and then she did it again about 50 miles of driving later.
I didn't catch the first four stalls on my torque app, because I'd just recently decided to stop logging every trip, with the thinking that it had been half a year problem free, why keep logging waiting for something that isn't going to happen. I did catch the 5th stall on the torque log. But I'm having trouble trying to figure out where it happened in a 30 min log.
First question where would yall start in tracking this thing down? Next what data actually should be logged? I think I've got some extra stuff in my logs that isn't necessary, and is maybe bogging down the system. I get one data point per second resolution on my logs. Are there ways to improve the resolution, will getting rid of some PIDs work?
Lastly I need to attack this thing smartly, without throwing time and money at unneeded parts. I had surgery and I've been out of work for 3 months and I'm looking at another 6 before I'm making money again, and there is no unemployment for the self employed. Also I only get 3-4 light weight upright hours a day to work, exceed that and I'm back on the couch battling swelling for a week.
Also is there anything I can do while driving to "flag" the stalls so I can find them more easily in the logs?
Ford 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Truck Started Blowing Fuse 45
I have an 03 6.0 F250. My truck started blowing fuse #45 and it would kill my gauges (fuel, oil, mph, rpm, temp, trans temp, and odometer) and I was just replacing the fuse and putting off the repair.
However, the most recent time my gauges blew, the fuse did not, and I put in a 20 amp fuse, in hopes that it would not blow so quickly, bad idea. So naturally, I ordered a new shift lever, in hopes that it would fix the gauges and I wouldn't have to deal with it anymore, but I think it was too late and something else needs to be replaced. What I could possibly have blown by having a larger fuse in there?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Go Over 45 MPH
I have a 2003 7.3. Suddenly a week ago when I left work, I noticed my truck wasn't picking up much, but i was in a 40mph zone. I then jumped on the freeway and noticed the truck would not go over 60mph. Once I exited and got on another road with a 55mph speed limit, the truck would not go over 45mph, I had the pedal pressed all the way down and would not go over 2000 rpms. Also, for the transmission to shift, I would have to let off the accelerator.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Will Not Crank Over
Started truck 3 times in 30 min. no issues with truck before tonight nice well cared for truck. Went to get a pack of buns at store came out --NO CRANK--all lights are on dash, etc, new starter a month ago, relay changed out in fuse panel just to see if there was a change. Bought two new Motorcraft batteries installed , NO CHANGE, so is it natural safety, key switch, electrical ignition switch, solenoid on starter, is there a solenoid between key and starter?
View 12 Replies