Ford Super Duty (1999-2016) :: 2006 F250 - Tow / Haul - Hard Downshift And Brake Pedal Gets Real Soft Until Full Stop
While in Tow/Haul with my 5th wheel when slowing down probably at 5 or 10 mph the last downshift is very hard and the brake pedal gets real soft until full stop. Afterwards the brake pedal is firm. Tow/Haul without the trailer is fine. It's an '06 F250 Supercrew 4x4.
View 6 RepliesFord Super Duty (1999-2016) :: Steering Absolutely Doesn't Work When Stop The Truck With Foot On Brake
I'm sure this is a common issue, but I don't know exactly what to search for. I have a 2001 F250 7.3L. When I stop my truck, with my foot on the brake, the steering absolutely doesn't work. I replaced the PS pump, which it needed, plus all the hoses and it got better, but the no steer problem while braking is still there. I have seen that an upgrade in pressure hoses may work?
View 1 RepliesFord Super Duty (1999-2016) :: 2005 F250 - When Engage Tow / Haul Button Transmission Doesn't Downshift Unless Feather The Pedal
I have a 2005 f250 super duty turbo diesel 6.0 automatic. The problem I'm having is, when I engage the tow/haul button the transmission doesn't down shift unless I feather the pedal. Also the engine will overheat at times. I've replaced the thermostat, but that's all so far.
View 2 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Long Pedal Travel When Applying The Brakes
I took delivery last week of a new 2012 F250 with a 6.7 Power Stroke Diesel. This is my third F250 with a Power Stroke Diesel. My first one was a 1997 w/7.3 PSD and my last one was 2001 w/7.3 PSD which I traded in for the 2012.
Now for my problem. The brakes seem spongy to me. When I am applying the brakes I get what seems like a longer than normal pedal travel (to me anyway) and soft. The braking isn't as good as my last two F250's. If I pump the brakes, the brake pedal firms up and the braking really improves. I have not contacted my dealer yet.
Ford Super Duty (1999-2016) :: 2008 F250 - Truck Will Not Stop Shaking When Driving
I have a 2008 F250 crew cab lariat 4x4 with 20 inch factory wheels that the steering wheel shakes during normal driving left to right. I bought this truck with 1500 miles on it. This shaking started at 50k miles and I was thinking it was a balance issue so I got new tires a month later since mine were about worn out anyways. They were factory replacement nitto terragrapplers. Shake was still there, swapped out for another set of nittos and shake still there, swapped to BFG AT KO's and shake better, but still there. I have gone through 10 or so balances, 5 roadforce balances, 2 alignments at 4 different shops including the ford dealer through the 3 sets. My wheels are scratched to hell and back from the careless people at the tire stores from so many balances.
My truck sat at the Ford dealer for a week just the other day and they changed the steering stabilizer. I thought it was gone, but a a few days later shaking started again. It almost feels as if every little bump, rut, crack in the road the steering wheel feels and shimmies (doesn't matter the speed, gets worse and more noticeable at higher speeds). The Ford Dealer says can't duplicate, but then when I go down there and test drive with them it's "oh yeah I see that, it shouldn't be doing that". The Ford Dealer says they can't find anything loose in the front end when I tell them to check tie rods, bearings, etc.
My truck has 62k miles on it now and it's driving me to the point of thinking about trading it on a Chevy. I love my truck, but it kills me everytime I make a payment and it rides like crap. I am still under extended warranty so I need to get this fixed before it goes out. I've also noticed that if I turn my steering wheel back and forth real quick while driving like warming up for a Nascar race I can feel a bumble in the steering wheel. This is NOT the death wobble as I use to get that around the 20k mile range and it disappeared and has never been back.
Ford Super Duty (1999-2016) :: 2002 F250 - Alarm Won't Stop Going Off And Cannot Start Truck
I have a 2002 F250 7.3l with an aftermarket alarm. I can't read what the third letter is on the decal MV? 2000 Modular Vehicle Security. I added a pic of the alarm decal below. The key fob it had was aftermarket for the alarm and stopped working about a year ago. Today I unlocked the drivers door with the key and the lights started flashing and I can hear a clicking sound. It done this a few times back when the key fob still worked and I just kept hitting lock and unlock until it finally stopped. It won't let me start the truck at all and I have tried unhooking the batteries with no luck.
View 4 RepliesFord Super Duty (1999-2016) :: 2000 F250 Triton V10 - Brakes Won't Stop Squeaking
I've replaced the brakes that weren't in that bad of shape anyways and even replaced one of the rotors as it was under federal regulations. I've even put the brake squeak goop on the back of the pads and it keeps squeaking and squeaking and it's driving me insane. Am i missing something here? I don't here any other super duty's squeaking on the road.
View 1 RepliesFord Super Duty (1999-2016) :: Left Front Caliper Is Not Squeezing Hard Enough To Stop The Truck Evenly
Having a problem with calipers again/still seems like always. Replaced all calipers twice in 86K miles on a 2000 f250 crew 4x4 because of stuck calipers. Replaced brake hoses and all hard lines in the rear about 2 years ago. My problem now is the left front caliper is not squeezing hard enough to stop the truck evenly. (pulls to the right) The rotor had some rust from sitting and after driving a for a while the rust is not completely gone as you would expect. Replaced caliper bled a couple of times. Caliper looks to be getting pressure enough to bleed and can see it move when brakes applied when engine not running. I don't have experience with Proportioning Valves but do you think that is the problem and how do I fix it?
View 8 RepliesFord Super Duty (1999-2016) :: 2004 F250 Truck Not Running Strong / Hesitating When Step On Gas Pedal
I have a 2004 f250 6.8L and recently I've notice the trick not running strong. Is hesitating when i step on the gas pedal. For example, I am driving on the feeder road and fixing to get on the freeway ramp, well i have to spent a bit harder on has pedal to gain speed, but it seems its struggling and I can hear muffler making like a flapping noise. Also when I am going between 40-65mph and I spent on it, the tricks kind of jerks and vibrates. Feels like its coming from transmission. I let go and step on it again and it goes away. What to check??
Miles : 96k
Year: 2004
No Check Engine Light
Ford Super Duty (1999-2016) :: 2012 F250 Truck Would Pull Left When Brakes Applied
I recently took delivery of a new 2012 F250. It was a cab chassis, we had a utility bed and lift gate installed from the upfitter along with heavy rear springs. From day one the truck would pull left when the brakes were applied. The brake pedal also feels mushy, not firm. It will firm up when I pump it. I could also smell burning around the left front of the truck when I would get out of the cab. Hot brake smell. Took it to the dealer with only 400 miles on it and they replaced the front pads and turned the rotors, and gave it back. In relatively few miles the problem was right back again.
Took it back to the same dealer last week with 1200 miles on it now. This time they say they replaced the rotors. I went and picked it up it this morning. Within 5 miles drive of the dealership I can tell the brakes are still bad. Now, it will kind of do a "head fake" when the brakes are applied, pulling slightly left or right, before deciding which way it wants to pull. It will pull right or left now during firm braking. And the brakes were stinking by the time I had it back to them. I turned around and took it right back to them again. Brand new F250?
Ford Super Duty (1999-2016) :: 2003 F250 - Clutch Pedal Not Retracting All The Way
I just bought my first Ford. Its a 2003 F250 SD with 5.4L, 5 speed manual, extended cab, 2WD. The truck is experiencing intermittent problems with the clutch pedal.
If I depress the clutch pedal for a long time, then sometimes it does not retract all the way. It does this, for example, when I am at a traffic light waiting for the next opportunity to make a left hand turn.
The truck runs and operates as it should even when this does happen. The easy response is to place your toes under the clutch pedal and pull it aft to its completely released position.
The master and slave cylinder and the booster spring attached to the clutch pedal assembly have been replaced and this condition still continues.
Ford Super Duty (1999-2016) :: 2003 F250 - Losing Power When Pressing Pedal
I have 03 f250 v10. just replaced the engine and got everything all connected and started it up and it idles great...the problem is that when you press the gas pedal it starts to drive but then it looses power and acts like its missing. cant get it to go 30 mph. While keeping it floored eventually it gets up to 2000 rpm and then starts to pick up speed.
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Rear Brakes Sticking
2003 F250 V10 4x4. I have a rear brake sticking so I assume I have to replace the calipers. Which brand should I go with?
View 2 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Vibration Under The Truck Near The Back When Accelerate
2003 f250 crewcab 6.0 auto 4x4. I all of a sudden started feeling a vibration under the truck near the back when I accelerate and when I let off the gas no other time. No noises or clanking just vibration. I can wiggle the driveshaft inside the carrier bearing do you think that could be it or is it the rear end.
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F350 - Hard Or No Start / Shaking In Low RPMs / Slow Response From Gas Pedal
I need fixing my 2003 f350 6.0 diesel, I have been working on this truck for a while and still am having problems, here was the original symptoms:
-Hard start or no start on a sunny day
-Rough idle for 10-15 minutes
-Rough shaking in the low RPMs (35 mph)[/COLOR]
-Slow response from the gas pedal
-boost would only get to 14
My dad and I then did many things to the truck in the shop, those things are:
-Air test and replacement of coupling going into oil branches (next to HPOP)
-Replaced EGR valve (no good)
-Replaced ICP sensor (leaking oil)
-Replaced ICP sensor and IPR valve piggtails (due to frayed wires)
-Cleaned Turbo
-Cut MAP sensor hose and reattached it (spliced on the end)
-New battery
-Performed a bubble test and found two bad injectors on passenger side (injectors #5 and #7)
-Cleaned and lubed tops of injectors
-Replaced O rings and copper crush washers on all injectors
-Replaced nipple cup O rings (tight)
-Blew out injector cups
-Bubble tested after injectors put back in (no more bubbles)
-New FICM, EGR cooler and oil cooler were already installed
-Ohm'd main engine wiring harness (good to go)
-Taped up frayed wires on fan clutch connection
-Increased wire gauge on the positive jumper between both batteries
-Sanded each ground on the batteries and engine, cleaned battery clamps, lithium greased connection points.
-Checked fuel for air (no air)
-Checked fuel psi (85 psi, plenty)
-Oil changed
After doing all of this (diagnosing as we fixed each thing) we now fixed many things including the hard/no start problem. Now, for the first three to five minutes:
-It starts right up
-Runs perfectly, no shake and instant response from the gas pedal and turbo
-Boost goes to 28
-ICP is 800-950 on idle
-IPR is 25-26.9% closed
After five minutes however:
-Starts to shake
-IPR % starts to raise
-Received no response from gas pedal (absolutely no power)
This truck has been torn apart like 8 times and I have to do it on my spare time.
Ford Super Duty (1999-2016) :: 2003 F250 - Pedal Slowly Go To The Floor When Hold Down Brake For Long
I don't know what's going on maybe some body can shed a little light on this. If you hold the brake pedal down for a long period of time you can feel the pedal slowly go to the floor. So no problem I'll change the master cylinder bleed everything brand new fluid. Don't drive it much we let the sister in law drive it we'll I jump back into it the other day to go to Home Depot and once again I notice it still does it. Could the hydra brake booster be bleeding by or what's else could be causing this it's driving me insane. I really can't imagine the hydra booster causing a problem but it's new to me. I was thinking about bleeding the brakes again thinking there maybe there's air but I have run 2 bottles of brake fluid through how much more??
View 8 RepliesFord Super Duty (1999-2016) :: 2003 F250 V10 Never Dies Just Loses Power And Drops Truck To Idle
We have replaced 4 fuel pumps on a row.
Voltage is good...even ran a fresh circuit.
Ran new supply lines
But, can't seem to understand the continued drop in pressure. It usually takes about a day of driving to crater after a new pump/filter is installed.
It never dies, just loses power and drops the truck to an idle. Funny thing...if I shut the truck off and turn it right back on...full power for a short period!
The truck is used on a ranch that has plenty of rough roads...thought inertia switch maybe but i believe that would stop fuel completely right?
I am totally stumped and so is the mechanic.
Ford Super Duty (1999-2016) :: Heater And AC / Blower Doesn't Seem To Blow Very Hard
My blower doesn't seem to blow very hard. I've been in other fords and the ac and heat blows great. Someone suggested that that I pull the fan motor and clean the blades.
View 4 RepliesFord Super Duty (1999-2016) :: 4x4 Doesn't Engage From Inside On F250
I have a problem on my F250 4x4. The 4x4 doesn't engage from inside. I tested for vacuum on the pipe that leads out of the solenoid. There seems to be no vacuum building on the outlet line. This is the line that go to the wheels. Is my solenoid stuffed. the pump works well and vents do not default to defrost.
View 14 Replies