Ford 7.3L Power Stroke (1999-2003) :: F250 Getting Hard To Start / Code P1670
But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Got Error Message P1670 / P0381 - Low Oil Pressure - Won't Start?
I had new glow plugs installed 3 weeks ago. Ran fine since. Today, first cold day. No start, oil pressure gauge does not move off zero, interceptor reads ICP 126. Oil level is good. WTS light does come on. Checked fuse 19 as I saw on another thread, it is good.
P1670 and 0381. My ford software is down, trying to reinstall. As soon as it is reinstalled, I can go thru the step process?
Ford 7.3L Power Stroke (1999-2003) :: Rough Idle - SES Light Throwing P0603 And P0470?
1999 f250 standard 266k miles ... Has a SES light throwing p0603 and p0470 ...
When the light is on the truck has a slight miss feeling to it and it seems low on power when the light goes off it will buck and sputter the lever off and it seems to have loads of power then the light comes on it will buck and sputter then go back to having low power. I have also checked the valve cover harnesses and they are good not sure where to go from here...
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 - Codes P1247 And P1248 / Noise Sounding Like It Lost Air Compression For A Few Minutes
My pickup has 316,000 miles on it. It's a 2000 ford f250 7.3 powerstroke. I have always bragged how my truck can pull anything because it has alot of power. Yesterday when pulling a 28' travel trailer up an incline I noticed I didn't have much power and it steadily got worse. Now I'm at a crawl when I hear a noise sounding like it lost air compression for a few minutes then the noise stopped. I stopped and looked to make sure everything under the hood was still attached and everything seemed fine.
I got back in and continued very slowly a few more miles home. Gauge were all good, never got hot. I put a scanner on it and it threw two codes. P1247 and P1248. I haven't noticed any unusual smoke. This is my second ford I've owned and know that when weather gets cold you may have to plug it in. But this truck it doesn't matter if it's 100 outside it will not start without plugging in for at least 1 hour. I've replaced all glow plugs hasn't worked. So I am assuming this break down now has something to do with it. I really am starting to not like fords!
Ford 6.0L Power Stroke Diesel :: Truck Died And Refused To Start - Code P0603
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.
Ford 7.3L Power Stroke (1999-2003) :: Idle Roughly - No Power - Got Codes P1280 And P1316?
Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Loosing Power - No CEL Codes - Half Of Engine Floods With Fuel
What I know the truck was running normal except if I stomped the gas pedal and let off it would not respond again until I shut off keys and restarted this was a month ago now the truck sounds like it has a lope tune.
When I hit the gas pedal it blows white smoke and if I press the gas while idling or driving it floods out I did the spray bottle test on manifolds the drivers side was plenty hot the passenger side is cold you literally can touch while it's running.
The truck sounds like it's only running on 4 cylinders it has gotten so bad I parked the truck. Also this truck always had poor mpg 8 to be exact city hwy and towing nothing changed the mpg at all it used to blow out wet soot that would fall down on the truck and anyone standing near it.
Mods unknown pcu program 4in straight pipe with 12in stack harpoon mod in tank
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Getting Codes For Both Wheels ABS?
F350 2001.
Constantly throwing codes for both front wheel's ABS. Ohm'd out both sensors - same reading
Ohm'd out wires leading to sensors - same reading
Ohm'd out rear diff speed sensor against a new one - same reading.
Pulled front sensor's cleaned and put my fingers in the sensor hole. What should I be able to feel? I'm wondering if the previous owner put non ABS hubs on?
Ford 7.3L Power Stroke (1999-2003) :: IDM Codes P01668 Communication Error
Truck wont start idm communication error all the fuses are good and the relay seams good I switched it out with another relay 340,000 miles how do I know if its the IDM r not... I'm sure the idm is not cheap...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: ABS Light Came On And Will Not Go Away - Codes C1233 And C1234
Immediately after replacing both front hub/rotors (and front pads and wheel bearings), my ABS light came on and will not go away. I finally ran codes a couple weeks ago while troubleshooting my CPS problem which left me stranded on the interstate while trying to get to the airport for a business trip.
Back in December, all I did was remove, clean, and reinstall the sensors like I always do whenever I have to R&R the rotors. I can't find any damage to the wires or connection points. I have re-removed and reinstalled each sensor again. I have cleared the codes, but once I start pulling out of the driveway, the codes come right back again for both front wheels.
There were absolutely no symptoms prior to the rotor replacement job, and this has been an ongoing and increasingly irritating visual issue ever since I did the brake job back in early December (I can't NOT look at the ABS light every time I start the truck, and I HATE seeing it stay lit)!
What bugs me the most is that I'm getting codes for BOTH sensors after replacing BOTH rotors. I MUST have gotten something wonky, but can't figure out what it was. Now I did replace all the drive line u-joints at the same time, but I never touched anything on the pumpkin or tranny in the process.
So, I have two questions..
1) Possible causes?
2) Possible solutions (I don't want to just start throwing new parts indiscriminately)?
From what I've read, Roland posted acceptable ohm values for the front sensors a couple years ago, so I can check that tonight.
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start Cold - No Codes
My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - No Codes - Crank But No Start?
I purchased this unit, non running, was told the HPOP was bad, after going through the unit top to bottom, Im stumped, below is a list of items serviced and or replaced with OEM parts.
0. changed oil and oil filter
1. Terminator 500 Hpop
2. New ICP
3. New HPOP lines.
4. New starter and solenoid
5. Serviced Turbo (rebuilt with new parts and WW wheel)
6. Serviced Injectors (shimmed) all test good.
7. new pass and driver harness, UVHC replaced, glow plugs replaced.
8. new heavy duty GPR
9. Tested IDM no issues.
10. Hutch mod on tank (re-circulator was stopped up) deleted it, added inline filter.
11. serviced fuel bowl with new parts, upgraded parts on fuel bowl new blow off valve, new drain valve, tested heater all good no blown fuses.
12 replaced faulty fuel pump
Might be leaving something out of this list, the truck has run but only for very short periods of time, (hence the dropping of the fuel tank)
fuel pressure at 70 psi, some white smoke, connected to on board computer, checked every conceivable possibility No DTC codes, my gut tells me it has to be fuel related but at this point I just have run out of things to check.
I have tested everything with a fluke multimeter, including the IDM and all the circuits to the 42 as well as all the way to the injectors and glow plugs and find nothing wrong all tests yield valid readings,
There may be other information available but my after market scanner does not show any issue, KOEO buzz test results good.
The three times I have had this unit running it was dumping lots of white smoke, however after the last round of dropping the fuel tank and replacing the fuel pump the white smoke has dropped to a minimum, but cannot get the truck to run, cranks, wants to start, almost starts, got it up to 800 RPM last try but just will not go beyond that point.
I cannot find anything wrong, must be something I am either missing or its something my cheap scanner can't pick up on.
Ford 7.3L Power Stroke (1999-2003) :: Won't Crank - Codes 0237 / 0470 / 1139?
how can this be? the WTS cycles as well as glow plugs. Brand new batteries, starter relay, starter. with a volt meter tested to make sure power is going to both connections to starter and they are good.cleaned battery posts, and all connections, is it that if there isn't 12v going to starter it wont function? only 3 codes: 0237, 0470 ( deleted EBPV), 1139 (unplugged fuel heater). 2001 f550 150k a/t.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Intermittent ABS Light - Codes C1230 And C1229
I have had an intermittent ABS light for a while now. Since I have gotten the injector o-ring issues, and oil consumption problems nailed down, I am starting to check other things off the list. I have 2 codes:
C1229 Speed Wheel Sensor Rear Center Coherency Fault
C1230 Speed Wheel Sensor Rear Center Input Circuit Failure
Ford 7.3L Power Stroke (1999-2003) :: Torque Pro And SES Light When Pulling Fault Codes
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
Ford 7.3L Power Stroke (1999-2003) :: Rebuilt Transmission Flashing O/D Light With Codes
I test drove my truck yesterday for the first time with the newly rebuilt transmission. I was gentle with the right foot and all seemed well. Once out on the main road it shifted by itself into overdrive for the first time and immediately the O/D light started flashing. I drove it home and shut her off. I test drove it 2 more times leaving overdrive off, no issues. With a snap-on scanner hooked up I let it go into overdrive and O/D light started flashing again, not immediately maybe 5 seconds after shifting into O/D.
Codes are:
p1316 IDM codes detected
P0717 Turbine speed sensor circuit fault
P0715 Turbine speed sensor circuit fault
P0500 VSS fault
10 minutes ago was my last test, O/D flashes only after it has shifted into overdrive. I checked the transmission wire harness and all connections are tight, trans oil level is good & trans temp never went above 150. Could this be a faulty VSS?
Ford 7.3L Power Stroke (1999-2003) :: Service Engine Soon Light - No Codes In Torque
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?