Ford F-150 - 1997-2003 :: ABS Light Comes On - DTC C1229 / C1230
1997 and up F-series trucks. If your ABS light comes on, it's about a 90% chance it's a bad rear axle speed sensor. If you scan it (or have it scanned for you) and the DTCs (diagnostic trouble codes) C1229 or C1230 come up, thats probably your problem. I'm a Ford mechanic and I repair about 2 or 3 of these a day. The magic number seems to be 40,000 miles, but I've seen them go sooner or long after that. It's VERY easy to change, it's on top of the axle housing. Just disconnect the electrical connector and remove the 3/8 bolt and it's outta' there. If you don't have access to diagnostic equipment to clear the codes afterwards, simply drive the vehicle a little and the computer will clear the light from the dash. The computer is constantly performing system checks and will realize the sensor is working correctly and shut off the light.
View 11 RepliesFord Excursion :: 2010 - ABS Light - Got Codes C1155 / C1230 / C1233 / C1234?
Used a 2010 or newer SD axle for there Coil conversion ? I did and am having abs issues. It's to cold to spend a lot of time outside figuring it out . I have these codes c1155, c1230,c1233,c1234. The right front sensor is brand new and the speedo works fine. Are the hubs maybe not compatible? Sensors plugged right in.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Airbag Light Flashing - No SES Light Or Fault Codes
Came on other day. No ses light or fault codes. What it means?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: ABS Light Came On And Will Not Go Away - Codes C1233 And C1234
Immediately after replacing both front hub/rotors (and front pads and wheel bearings), my ABS light came on and will not go away. I finally ran codes a couple weeks ago while troubleshooting my CPS problem which left me stranded on the interstate while trying to get to the airport for a business trip.
Back in December, all I did was remove, clean, and reinstall the sensors like I always do whenever I have to R&R the rotors. I can't find any damage to the wires or connection points. I have re-removed and reinstalled each sensor again. I have cleared the codes, but once I start pulling out of the driveway, the codes come right back again for both front wheels.
There were absolutely no symptoms prior to the rotor replacement job, and this has been an ongoing and increasingly irritating visual issue ever since I did the brake job back in early December (I can't NOT look at the ABS light every time I start the truck, and I HATE seeing it stay lit)!
What bugs me the most is that I'm getting codes for BOTH sensors after replacing BOTH rotors. I MUST have gotten something wonky, but can't figure out what it was. Now I did replace all the drive line u-joints at the same time, but I never touched anything on the pumpkin or tranny in the process.
So, I have two questions..
1) Possible causes?
2) Possible solutions (I don't want to just start throwing new parts indiscriminately)?
From what I've read, Roland posted acceptable ohm values for the front sensors a couple years ago, so I can check that tonight.
Ford 7.3L Power Stroke (1999-2003) :: Torque Pro And SES Light When Pulling Fault Codes
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
Ford 7.3L Power Stroke (1999-2003) :: Rebuilt Transmission Flashing O/D Light With Codes
I test drove my truck yesterday for the first time with the newly rebuilt transmission. I was gentle with the right foot and all seemed well. Once out on the main road it shifted by itself into overdrive for the first time and immediately the O/D light started flashing. I drove it home and shut her off. I test drove it 2 more times leaving overdrive off, no issues. With a snap-on scanner hooked up I let it go into overdrive and O/D light started flashing again, not immediately maybe 5 seconds after shifting into O/D.
Codes are:
p1316 IDM codes detected
P0717 Turbine speed sensor circuit fault
P0715 Turbine speed sensor circuit fault
P0500 VSS fault
10 minutes ago was my last test, O/D flashes only after it has shifted into overdrive. I checked the transmission wire harness and all connections are tight, trans oil level is good & trans temp never went above 150. Could this be a faulty VSS?
Ford 7.3L Power Stroke (1999-2003) :: Service Engine Soon Light - No Codes In Torque
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
Ford 7.3L Power Stroke (1999-2003) :: Intermittent Engine Light / Momentary Surge At Highway Speeds
I have a 1999 F350 200,000 miles. Now getting an intermittent engine light. Still runs well, although once or twice I felt a momentary surge at highway speeds. The light is on intermittently about 1/2 time. I read the codes and the following codes, as in the thread title, came up:
P0280 - ICP circuit out of range - low
P0113 - intake air temp sensor circuit - high input
P0470 - Exhaust back pressure sensor circuit malfunction
P0478 - Exhaust pressure control valve - high input
What would make these all code at the same time? Would these not make a noticeable problem driving? And how do I resolve these?
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Intermittent Power Loss?
I have a F350 that has intermittent power loss.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Steering Intermittent Or No Power Steer
My 7.3 power steering is acting up. Feels like I am up against a rock. At slow speeds like parking lot maneuvering I struggle to turn wheel. Then all of a sudden I'll get power steering back and wheel will rapidly turn. Freaky.
Brake pressure is fine. They shutter pretty bad even with the new rotors I just put on but they have good pressure. But the steering is intermittent or no power steer.
I saw online to run engine at 2000 rpm and try steering but no change. Still no power steer. There is fluid in reservoir. There is fluid seeping up steering column from steering box. No clue if this is related or unrelated.
How to troubleshoot further. I hate throwing parts at problems before truly diagnosing. Also have pretty aggressive lurching during turns in four wheel drive. It's present on dirt road but worse on pavement. Don't know if this is related or not.
Ford 7.3L Power Stroke (1999-2003) :: Power Steering Loss Intermittent - New Pump?
I have a 2000 Excursion. This weekend, I noticed some intermittent failure of the power steering where it seemed like the pump was not engaging and then would all of the sudden. Deciding to try to head off a failure, I got a reman unit from Oreilly and installed it this morning. It was fine when I tested, had good brakes and went locked to lock quietly without fuss. Let the house and within a mile, I lost steering and brake assist. I stopped and turned around, but what I am noticing is that at idle, I have no power steering, but when the RPM's are up, I do.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Intermittent Loss Of Power - Momentarily Stuttering
Intermittent loss of power (could be describe momentarily stuttering) with momentary illumination of the check engine soon light. Its only happened a couple of times. Maybe about a year ago (I changed the fuel filter after it occurred). It occurred again about a month ago and then again yesterday. About a month ago I had a friend with a scanner look at the codes and he said there was only one and it was for low fuel pressure. Its been maybe 5k since I changed the fuel filter.
The truck is driven intermittently, maybe 5k or 6k a year, and usually parked with a full tank of fuel. What areas I should look at to correct this? I got my stock 2001 F350 4x4 manual transmission in 2004 with about 157k miles. Today I've got about 228k miles.
Ford 7.3L Power Stroke (1999-2003) :: Intermittent Rough Motor / Black Smoke And Low Power
I have an Excursion with 220k miles. I've owned the truck for 6+ years and had very few problems. I change my own oil and fuel filters, but beyond that I know next to nothing about the diesel motor. I do run a DP Tuner with the standard 80 hp program. And a 4" exhaust. Everything else is stock. I do keep it plugged it for the oil heater and the battery tender just about all the time now.
This latest issue started yesterday morning when my wife jumped in a cool truck to take the kids to the dentist (not warmed up but still 55 degrees ambient). A few miles down the road (35 mph max) the motor began stumbling and rocking and black smoke coming from the exhaust with reduced power. She pulled off and kept it running (very rough and rocking) and put it in park for a minute. When she put back in drive, it shifted heavily but the power was normal so she went on her way without any problems. The only report I got sounded like the motor was just cold and rough, so I thought nothing more of it.
Yesterday evening we drove it about 70 miles on the highway (72 mph max) with no issue at all, but when we continued on surface streets toward our destination (50 mph max) it did the same thing, but would not settle back down. I kid you not that it went through gallons of fuel the last 12 miles or so, just dumping black smoke out the exhaust. It felt to me like we were running 1/2 the motor, like the plugs weren't lit. Very rough and rocking and very little power (comparatively, at least). I had to switch to manually shifting the trans to get going and the shifts were much rougher than usual. Idle was low and rough but it never stalled. Behind me there was a huge smoke screen this entire time.
We made it to our destination and parked it. Did our thing and after 5 hours went out with finger crossed. Started right up and ran perfectly the entire 91 miles home. No motor or trans issues at all. Currently running 10/40 synthetic oil that I just changed about 2000 miles ago. Oil level is perfect. 3/4 tank of fuel with standard level of Diesel Kleen added. Fuel filter is less than 10k miles old. Temps yesterday were 65-70 on the drive down and 50-55 on the way back.
I jiggled all sorts of connectors this morning and didn't find anything loose.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Intermittent Battery Light On / Off
I have a 2003 F 350 Crewcab 6.0 liter SD. I was preparing my truck for the first haul of the Summer. I noticed that my batteries were on their way out after 2 years old. I replaced them and noticed I had an intermittent battery light coming on/off on/off. It seemed like only at lower RPMs. So the day of my trip, I ended up changing out the alternator.
The trip went fine, however, I noticed that pesky battery light came on and then off a few times. I also got a hot plastic type smell from the front of my truck.....you know that hot plastic smell Anyway, I got home just fine. Via Torque Pro, my battery volts were reading 12.2ish when my battery light came on, but then would quickly return to 13.9.
Since I"ve been home, I have read about fixing the grounding points for our trucks and also adding a second ground wire and a second hot wire from battery to battery. I can not find exactly where the ground's lead to. I still have that fricking battery light coming on .....more often that not. How to chase this problem.
First I need to find out where the ground wires go to. My volts of recent have been reading 11.5-12ish when the truck is running and the friggin battery light is on. I did search and found a few links to this problem, but where to find the grounding points.
Ford 7.3L Power Stroke (1999-2003) :: Idle Roughly - No Power - Got Codes P1280 And P1316?
Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Loosing Power - No CEL Codes - Half Of Engine Floods With Fuel
What I know the truck was running normal except if I stomped the gas pedal and let off it would not respond again until I shut off keys and restarted this was a month ago now the truck sounds like it has a lope tune.
When I hit the gas pedal it blows white smoke and if I press the gas while idling or driving it floods out I did the spray bottle test on manifolds the drivers side was plenty hot the passenger side is cold you literally can touch while it's running.
The truck sounds like it's only running on 4 cylinders it has gotten so bad I parked the truck. Also this truck always had poor mpg 8 to be exact city hwy and towing nothing changed the mpg at all it used to blow out wet soot that would fall down on the truck and anyone standing near it.
Mods unknown pcu program 4in straight pipe with 12in stack harpoon mod in tank
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Partial Crank And Intermittent Start
Anyway, I went out to start my truck just now and I'm getting a weird symptom.
The truck gets partial revolution and then to me it seems like the starter bendix pulls back in prematurely and this nasty clank and then a slight "zing". all within a second.
If I try a few more times, it seems to fire. But all the attempts before it fires sound pretty nasty to me.
Does this sound like a symptom of a bad starter/bendix?
A little further history, my excursion was broken into several years ago and they stole my pioneer head unit, in doing so, they forced the shifter down and since then it has been a little "loose". I'm wondering if it could be a neutral safety switch on the transmission?
Anyway, I'm getting ready to order a new neutral safety switch but wondering if I should go ahead a purchase a new starter as well?
Ford 7.3L Power Stroke (1999-2003) :: Intermittent Starting / Spin Like A Top But Not Fire
2002 7.3 PS TD.
Lately sometimes when I get in and start the truck all is well. Then the next time it will spin like a top, but not fire. New batteries. Then it will fire right up. It may go a few weeks, or days, then it happens again. Temperature does not seem to be a factor. It also doesn't matter if the engine is hot or cold. Once when rounding a corner at low speed, it just died, then started right up.
I recently changed the fuel and air filters. I think the glow plugs are getting old. In cool weather I turn the key on for about 1 min. before cranking. I have 110,000 on the engine with all original parts.