Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?

Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.

By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.

Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).

It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).

It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.

Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).

I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.

View 5 Replies

Ford 7.3L Power Stroke (1999-2003) :: E99 Stalling And Sometimes Running Rough - Codes P1280 And P1247

E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.

The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.

Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.

The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.

I was told to check the IPR% under full throttle which I did and it never went higher than 36.7

The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.

Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.

Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.

Here is a link to the videos I got :

e99 7.3 ICP fluctuation while driving - YouTube

e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube

View 5 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 - P1316 IDM Codes Detected Coming Back Upon Start Up

I've been battling this truck for over a month now and starting to go a little crazy, It's a 2001 f350 7.3L, with a "used" 7.3L engine from a 1997. Transferred all the necessary parts to make it happen. Keep getting the evil p1316 idm codes detected coming back upon start up. Anywhere between 5-30seconds after starting the left bank dies. I've gone threw and replaced the IDM with a reman unit. New valve cover gaskets (with new harness). even went the extra mile and put in a new power wire (for the driver side) running directly from the new valve cover into the IDM bypassing a connector above the left valve cover. All injectors are checking out around 3ohms. With glow plugs all around 1-2ohms. What's interesting about this is, I can disable any one of the injectors on the left bank (doesn't matter which one) and the engine runs great considering it's down on one cylinder. But when I hook up that last injector it will kill the whole left bank again.

View 13 Replies

Ford 7.3L Power Stroke (1999-2003) :: No Power Suddenly - Got Code P1316?

Here's the story. Truck has showed no signs of rough running. Wife drives truck around town. Truck up to temperature and doing fine on a 90 degree day. Stops at red light. Makes left turn engine light comes on truck seems to be running on 4 cylinders. Pulls over light goes off engine idles perfect. Pulls back on road light on no power. Gets truck to a local friends house lets it sit til I get off work.

I check for codes get p1316. Drive truck toward my house no problems for 4-5 miles then does the above with me. Limp it home. I know it is pointing at a wire problem to injectors and or IDM. Did a buzz test passed fine. Plan on pulling valve covers and looking for the usuall things. Any thing I am missing? What will a kOEO test tell me? Should I run one? How common is IDM to go out? One last thing just put a rebuilt transmission in it 3 days ago may be unrelated it seems to be doing fine.

2003 f-350 cc 7.3.

View 11 Replies

Ford 7.3L Power Stroke (1999-2003) :: Intermittent Starting / Code P1280

My 02 f250 w/ 7.3 won't start. Cranks and nothing. No smoke or anything. For the last year It has had a intermittent starting problem, where I would drive it for 15-20 mins. If I shut it off like I would if I was at the fuel pump and then restart it, it wouldn't. I'd have to wait 30 minutes with a hood open and then it may start. Other times I would have to wait hours.

I tried replacing the crank position sensor, the fuel pump and filter.I did all this in the Last 300 mile . There's No change. After a week or two of sitting it won't start. What can I check and what can I try.

To add more info. Since I am not the original owner I pulled the computer that is located behind the ebrake to see if someone else had installed a chip, as I've heard that if that chip goes bad then the truck won't start. I disconnected that battery and pulled it. Negative on any chip. Put it all back together and tried again. No start. I borrowed a code reader tonight and pulled a P1280 code. I'm back to square one.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Code P1316 - New IDM?

What do I do? Do I need a new IDM?

View 3 Replies

Ford 7.3L Power Stroke (1999-2003) :: Bad Stutter / P1316 Code

Wife put fuel in my truck drove it home and as soon as I started it back up it was running rough as hell. When I got to the freeway it got real rough at 1500 rpms in overdrive. If I bring it up over 2000rpm it's better but still feels rough. When I got off work and started it up I got the p1316 code.

I did some research tested plugs on the valve covers a few pins were over 5ohms so pulled the valve covers did the 50cent mod to shimm the under valve cover wiring harness. All pins are around 3.5 ohms. It did not fix the problem.

I then dropped the tank thinking maybe the pick up was gunked up. I've read all the horror stories about the delamination in Ford tanks. Good news is that I have a plastic fuel tank. Bad news is the screens though dirty weren't dirty enough to cause my problems. Where should I go from here?

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280

2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: Misfire Code P1316 / Smokes Bad If Rev It

I have a 03 7.3 runs like crap. buzz test says cyl 2 and 4 have high to low side open. the only code that's hard is p1316. it also says cyl 1-3-4 fail balance test but not always some times only 2 fail.... I ohm tested injectors all the way to the idm and all are between 3.1 and 4.2 ish. So I guess I can rule out wiring. it smokes pretty bad if I rev it. it was running good till I parked it for 2 days. I did put HSS in oil 2 weeks ago to try clean out little rough acceleration. I did find my ipr nut fell off and spacer ipr was just floating around on the shaft I put that back together it was laying there.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280

I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).

Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.

After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.

I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Sluggish - CEL On - Code P1316

Just a heads up when it comes to this code. Today at work I was working on a 2000 f350 that the driver neglected on telling me he had a CEL on and truck was kind of sluggish (drivers are idiots they cant tell the difference) but no miss or any sign of problem except the CEL (he had electrical tape on the cluster. Well I put my AE to see the vitals and immediately code p1316, so I went to do a buzz test revealing that cylinder 1,3,5,7,6 were short to open circuit (forgot the codes) but they all sounded healthy. My next step since it was a quick and easy to do was to check the passenger side uvch to see for burnt pins and what not but everything checked out.

Checked the driver side #6 cyl for the same problem bit a no go. I ohm tested the injectors all of them checked out, wires all the way to the idm checked out so at this point I was in my atemp to see what the hell was going on I decided to install my obs idm on, and guess what happened next it worked immediately the sel did not come up and when I test drove it, my god it felt like a new truck.

Just a side note the idm, had no sign of water damage, and like mentioned to the untrained person most would not tell the difference on how it ran. To anybody that has checked and can't find the problem make sure you really and I mean really check your IDM really good.

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: Code P1316 Thrown When Engine Is Cold?

I keep getting my SES light coming on in the morning when my engine is cold. I'm getting code p0603 and p1316. I was told the first one is just from using my tuner. The second code is the injector driver module, just trying to figure out what is causing it to throw the SES light only when cold.

View 6 Replies

Ford 7.3L Power Stroke (1999-2003) :: Stumbling For The Last Two Years Intermittently / P1316 Code

I'm running a 2000 f250 7.3. The truck has been stumbling for the last two years intermittently. I did the 50 cent mod last fall to the uvch's. Changed CPS, idm, air flow sensor. This last week it finally threw the p1316 code so I have something to go off of. Trucks falling on its face so I parked it. Tore it down last night. Ohm tested all the injectors last night cold and all read around 3ohms. Tested the uvch's and continuity looks good on both sides. Tested them through the valve cover seal, tested fine. Tested them through the first harness and fine. All I have left to check is all the way to the idm. Still no luck finding the problem.

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: SES Light Came On While Idling At A Stoplight - Code P1316

Well, truck is throwing me for a new loop the day I pick it up from the body shop (crazy, right?). I started out driving it and had a blue haze - I figured it had some air left in the system from doing my injectors so I left it and it cleared up after about 20 miles. I noticed that my SES light came on while idling at a stoplight, but went off when I took off. Figured it was a fluke and kept on getting on.

Well, next light it does the same thing - idle the light is on, take off the light is off. Reading the code yields P1316 - so I pull over and running a buzz test to fetch the IDM codes. Guess what? No codes. All sounded fine, so this is where I got really confused as I'm getting huge mixed signals from this truck suddenly.

As I got to watching my gauges, I noticed that I was idling around 10.8 IPRDC and 530-560 ICP, and when I would get about 16-18 IPRDC the code would go away. Did a near-WOT run when getting on interstate as a test to see how it'd do, and saw IPRDC get up to 98% - the highest I have EVER seen it get on this truck (no idea if it is related or not). I have a log from moving around the lot that I will try and upload soon.

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Got Code P1316 - Injector Wiring Harness?

I have a 2000 Ford F550 7.3. I bought a Superchips programmer to read the codes on my truck and up pops this P1316, so I did some research and found out that the most common problem is the injector wiring harness. I bought new valve cover gaskets and the injector wiring as well because the truck is old and I figured new wires wouldn't hurt.

So after installing the new wiring harness and gaskets I'm still getting this Code! The truck idles rough and serge's sometimes, also there is a lack of power and some shaking between 40 and 50 miles per hour, however form 50 to 60 MPH seem's to be just fine. I don't trust the "Mechanic Shops" around here and will only take the truck in as a last resort.

View 10 Replies

Ford 7.3L Power Stroke (1999-2003) :: Fuel Relief Valve Is Stuck Open - Code P1316?

If the fuel relief valve is stuck open would it possibly throw a P1316 code?

View 4 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Truck Missing And White Smoke Coming Out - Code P1316

Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Hesitating While Cruising Along At 35 MPH Roughly

I have a 2002 7.3 160k miles and recently it has been hesitating while cruising along at 35mph roughly. In park right off idle the engine does shake but if i give it a little more pedal the shake clears out. Not sure if that has anything to do with my issue but im just throwing it out there. Anyways cruising down the road the truck will hesitate almost like its not getting enough fuel the engine bogs then picks up then bogs and picks up but it i give it more pedal the truck gains speed and the issue stops and i can resume cruising at say 45 and not feel this hesitation at all.

On the toll road i never feel the hesitation cruising at 2k rpms. A problem that might of lead me to this issue was in the winter below 30 degrees i would drive the truck get to a stop light engine still cold or maybe warming up off the cold mark but when i go to take off from a light its like my fuel pedal doesn't work but the rpms will climb a little then the truck takes off and jerks really hard since i had the engine rev'd up. which made me think throttle sensor immediately or maybe the trans is having issues. since its warm out I don't have that issue now so i believe that it the trans. do you think maybe my hesitation now is also the trans? I never get a CEL. I did recently change the coolant temp sensor and now i am having this hesitation issue.

But I was told the ECM does not care about coolant temp on an auto truck so i dont see how that could affect my performance. Instead the autos monitor oil temp and the manual trucks monitor coolant temp correct? I had an issue like this with the truck years ago when i purchased it i was leaving the gas station on very cold maybe 10 degree day and the truck fell flat on its face and threw a bunch of codes but i let off the throttle and got back in it and it took off like nothing happened. So im not convinced the coolant temp sensor was defective from factory. But this old problem of not accelerating seems to be coming back to haunt me.... and i think its in a new form with the hesitation once in a while. I think i forgot to mention the hesitation isn't all the time!

View 5 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Running Roughly While In Gear

I have a 2000 Excursion, with about 199k miles on it, 2WD, Automatic. Recently started running rough, but only when in gear. Seems to occur more when in reverse. But, within the last few days, i have noticed it starting to run rough while in park. You can rev up the engine and let it settle, and it will sound fine, run fine. Don't see any issues while driving it, between the engine or the trans.

I am leaning towards the injectors being the issue, but not 100%. The engine also started sounding sloppy when shutting off, like it wouldn't stop rotation right when you kill it. It doesn't stay running, but has that extra clank, like it takes longer to stop. (Hard to describe it) I just put some cleaner in it yesterday, and i was going to see if that works only.

View 1 Replies