Ford 7.3L Power Stroke (1999-2003) :: Airbag Light Flashing - No SES Light Or Fault Codes
Came on other day. No ses light or fault codes. What it means?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford 7.3L Power Stroke (1999-2003) :: Rebuilt Turbo Still No Power And No Boost?
Well I am at a loss now. Rebuilt the turbo with a new wheel and kit from Riffraff. I still have no power, no boost and no codes. The new wheel whistles. I can hear it. It sounds way better than the old one. But still no power. I really don't know what to do now.
View 14 RepliesFord - Mountaineer :: 1999 - O/D Light Is Flashing Once In A While - Transmission Codes
I have a 99 Mountaineer AWD 5.0 (143K) and having some issues with it. O/D light is flashing once in awhile so decided to check the codes.
- P07401 (Torque converter)
- P1728 (Transmission slip)
The truck shift fine and no having really issues when driving even if there is a weird noise around 70mph.
Ford 7.3L Power Stroke (1999-2003) :: Engine Rebuilt / Now Trans Doesn't Engage
Paid a shop 9000 to rebuild engine. Went to pick it had a major oil leak from back of the motor. They pulled the Trans and resealed the back plate. I test drove the truck and had some boost leaks and the AC needed charged. They pulled the truck in this morning and fixed those items. Now the truck will not move in any gear.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Front End Rebuilt - Hopping And Vibrating At Any Speed Or RPM
I recently (1month ago) rebuilt my entire front end. The only things that were not replaced are track bar, steering box, front driveshaft, and sway bar bushings. I'm having the same issues that I had before the rebuild. It just feels like the front is is on basketballs. Hopping and vibrating at any speed or rpm. On a smooth road or on the highway it feels like I'm hitting bumps that aren't there.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Overdrive Light Flashing Sometimes
The overdrive light is flashing but not all the time. What does this mean?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Overdrive Light Flashing - TSS Not Detected
My F350, 7.3 L. is flashing the overdrive light. Had a pro do a scan that said no Turbine speed sensor signal.
I would like to know where the TSS is located and then see if it has corrosion other reason not to connect.
Ford 7.3L Power Stroke (1999-2003) :: Flashing OD Light - Code P0741
I am trying to make sense of a P0741 code accompanied by a flashing OD light.
The truck is a 2002 (12/01) build date) F250, 7.3,4x4, Auto, with 245,000 miles on it. The truck seems to shift fine but around 40/45 it feels like the TC does not lock, followed by the flashing OD light.
The transmission was serviced 500 miles ago but the OD light flash was intermittent until last week, now its been constant. I want to take care of it before I do any damage.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Got P1832 Code - Flashing OD Off Light?
I have a persistent issue with the OD off light flashing on my 2001 7.3L auto 4x4. Scanning it with AE I get the P1832 code. The truck runs and drives just fine. It shifts nice, goes into overdrive, locks up, etc. If it weren't for that blinking light I'd think it was all perfect. I've checked all the connections, replaced the range switch / neutral safety switch, replaced the VSS on the rear axle, checked all light bulbs and fuses. I've checked MOST of the relays in the truck.
I pulled the tranny drain plug and poured out a bit of fluid into a clean pan, it looks and smells good. AE also tells me that it's not communicating with the ABS system (although there's no persistent ABS warning light on the dash), the Airbag, the Overhead Trip Computer, the Parking Aid (which I don't have...), or the Enhanced Powertrain. The temperature on my overhead display is reading -40F which is clearly wrong.
I've looked for a comprehensive wiring diagram for the truck, but can't find one. I'm trying to figure out if there's a connector or module that these various functions go thru that might be the problem. Am I missing a ground somewhere? The frame was just powdercoated......am I not getting a good ground connection? In complete disclosure, I have torn this truck apart and re-assembled it out of several different trucks as outlined in this thread.
[URL]....
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - OD Light Started Flashing
I have a 02 f250 4x4 7.3l.... I drove it all weekend and no problems. It sat till yesterday I got in it to go to church. It started up and had a little miss was around 60 f. Then the od light started flashing. Not in any code just constant flash. I was parked down in my drive way. It idled fine but acted like it wouldn't take fuel. So looked around and found the hose on the map sensor was broke.
So today I fixed the hose. Checked the oil level and battery connections. Still running weird and flashing od light. I got under the hood and wiggled plugs I unplugged the ice. It revved up then back down and started running smoothly. Got in it and it backed out of the drive way. It ran and drove fine. What I need to know is why??? The ice is a new one from Ford.
Ford 7.3L Power Stroke (1999-2003) :: ABS Light Came On And Will Not Go Away - Codes C1233 And C1234
Immediately after replacing both front hub/rotors (and front pads and wheel bearings), my ABS light came on and will not go away. I finally ran codes a couple weeks ago while troubleshooting my CPS problem which left me stranded on the interstate while trying to get to the airport for a business trip.
Back in December, all I did was remove, clean, and reinstall the sensors like I always do whenever I have to R&R the rotors. I can't find any damage to the wires or connection points. I have re-removed and reinstalled each sensor again. I have cleared the codes, but once I start pulling out of the driveway, the codes come right back again for both front wheels.
There were absolutely no symptoms prior to the rotor replacement job, and this has been an ongoing and increasingly irritating visual issue ever since I did the brake job back in early December (I can't NOT look at the ABS light every time I start the truck, and I HATE seeing it stay lit)!
What bugs me the most is that I'm getting codes for BOTH sensors after replacing BOTH rotors. I MUST have gotten something wonky, but can't figure out what it was. Now I did replace all the drive line u-joints at the same time, but I never touched anything on the pumpkin or tranny in the process.
So, I have two questions..
1) Possible causes?
2) Possible solutions (I don't want to just start throwing new parts indiscriminately)?
From what I've read, Roland posted acceptable ohm values for the front sensors a couple years ago, so I can check that tonight.
Ford 7.3L Power Stroke (1999-2003) :: 4R100 Trans Won't Go Into 4th / OD Light Flashing And Occasionally Overheats
I have an early 1999 Ford F350 4x4 7.3. I purchased it used about a year ago. The trans was replaced with an ATS 4R100 and a billet torque converter. I have the paperwork for it to confirm it along with the mileage when it was installed. It currently has about 35k on the new trans.
Several months ago the trans heated up to about 200 degrees on my trans temp gauge that was already installed when I purchased it. Not a huge deal and after pulled over and high idling it off I went and no problems.
About a month ago I was towing my fifth wheel when I noticed the temp rising on a level grade. I also noticed the OD light flashing. I made it home and when I went to drive it the next day light was not flashing and it shifted and drove like normal without the trailer.
I towed the trailer again and same thing, OD light flashing and started heating up. I changed all the fluid and flushed it based on the trans flush procedure I got in this forum and replaced with an OEM trans filter. Towed the next day and everything was good. Temp was good and no OD light flashing but I lost 4th gear. All other gears shifted fine, no slipping, just won't go into 4th.
On my way back home the OD light started flashing again and instantly the heat started rising on the trans again. I was finally able to get it into 4th if I let off a little, but as soon as the OD light started flashing I lost it again.
I have a friend of a friend who works for Ford who offered to come over to hook his scanner up. When he hooked it up there was no stored codes from the OD light which we both thought was odd. Took it for a test drive and the OD light started flashing so we could get some readings. He said it showed an error shifting from 1 to 2 and another error when shifting from 3 to 4. I unfortunately forgot to ask him for the specific codes. He tried to read the torque converter info but said my truck was to old and the PID was not supported to read that info.
He said it appeared it was mechanical but without some type of break out box where he can physically shift the gears he couldn't say for sure if it was mechanical or electrical. He did not seem to interested in doing that test for me as he rebuilds trans on the side and said he could rebuild it for me.
It seems my overheating takes place when the OD light starts flashing. It still drives fine and shifts smooth with no issues with or without the OD light flashing. 4th gear usually doesn't work but on a rare occasion it will go into 4th fine which makes me believe it may be electrical.
I am new to diesels but have learned a lot about my 7.3 lately. I recently installed injectors, up pipes, hutch mod, and several other little things so I can get things done myself but am just a DIY'er who can follow good directions. I know very little to nothing about transmissions though.
While working on another issue I did notice there is a large wiring harness that connects up on the driver side of the trans. I unplugged it and was checking the wires and after removing the dirt and crud on it you could see the outside wire sheathing had deteriorated exposing the copper. I bought some liquid electrical tape and sealed everything up. I did look for a replacement wire harness at the time and the one I ordered was very similar but the plug was different so that is why I used the liquid tape at the time. I did not seem to have a problem at the time after fixing it but wanted to mention it here in case that may be an issue.
I also thought swapping out the solenoid pack may fix it. I did not want to drop the trans and send it for a rebuild if I did not need to. I know there are some other sensors associated with the trans like the TSS I think but don't know if they are even related to my issue.
I tried getting the codes from the guy but he does not have them and I can't get him back out. I have an OBDlink device connected to Torque on my phone but I couldn't get it to read trans codes. Could be user error.
Ford 7.3L Power Stroke (1999-2003) :: F350 Leaking Fluid / OD Light Start Flashing
Saturday morning my grandpa drove my F350 into town pulling our 4-horse trailer (With living quarters). I wasn't with him, but I was told the following: he started smelling something hot and noticed the O/D light start flashing. Now, this man is not the most intelligent man on the planet and uses the O/D to "slow down the engine" when he starts and stops - i.e. uses it as trailer breaks. I have asked repeatedly for him to quit, but as best as I can tell, he continues to do so.
After the burning smell, a driver pulled up next to him and pointed down - he looked to see smoke and the truck puking fluid everywhere. He said he thought the truck lost power because he couldn't get it to move. Ended up getting it towed. The tow truck driver checked my fluid level and said I had an extremely small amount of transmission fluid left in the truck...which made sense as the fluid was all on the ground underneath, lol. Fluid was NOT red and looked really gross and there was DEFINITE burnt smell to it.
My question is this - what in the world could have caused the truck to do this (I read that is could be from overheating?), and what should be my next course of action? It is home and in my backyard right now (Classy!). It starts and runs fine, but since there is little to no fluid left, you have to hammer down on it to get it to go anywhere. It does move, however.
Ford 7.3L Power Stroke (1999-2003) :: OD Light Starts Flashing After Coming To A Complete Stop
I have a 2000 F-350 dually. I am having an intermittent problem with the the OD light. The symptoms are after coming to a complete stop the OD light starts flashing and when trying to move forward it feels as if the brakes are dragging and sometimes stalls out the engine. The codes read with a Superchip 1705 are p1670,p0720, and P0503. When I shift into park, the engine rpms jump from idle to about 1500-1600. I have replaced both the differential VSS and the transmission OSS but still have the same problem.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Intermittent ABS Light - Codes C1230 And C1229
I have had an intermittent ABS light for a while now. Since I have gotten the injector o-ring issues, and oil consumption problems nailed down, I am starting to check other things off the list. I have 2 codes:
C1229 Speed Wheel Sensor Rear Center Coherency Fault
C1230 Speed Wheel Sensor Rear Center Input Circuit Failure
Ford 7.3L Power Stroke (1999-2003) :: Torque Pro And SES Light When Pulling Fault Codes
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
Ford 7.3L Power Stroke (1999-2003) :: Service Engine Soon Light - No Codes In Torque
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
Ford - Taurus :: Transmission Rebuilt / CEL On And Multiple Codes Came Up
I have a 2005 Ford Taurus. We had an $1800 rebuilt transmission put in 8 months ago and it's already giving us problems! The engine light has also been on. We took it to autozone and multiple codes came up. We've already put way too much money into this piece of shit and I don't want to get screwed by another mechanic! Where do we go from here? Is there anything we can fix ourselves? The codes are p0300, p0301, p0305, p0316....
View 11 Replies