Ford 7.3L Power Stroke (1999-2003) :: Erratic Fuel Gauge - Level Would Register Full When Only Half A Tank Or So
I've been having a very erratic fuel gauge issue as of about 2 months ago. My fuel level would register full, when in fact I knew it only had 1/2 a tank or so. Then 5 minutes later it would be pegged on full. Under a 1/2 tank the gauge would read any where from 1/2 to empty from 1 minute to the next. So last week I decided to drop my tank and take a look. I was thinking maybe my fuel sender was broken, maybe a loose wire in the tank, or even that my float had dropped off in to the tank.
After dropping the tank, I removed the PK-Up and sending unit and everything was intact. I placed my ohm meter on the sending unit and it checked out fine. So I took the Pk-up and rolled back up underneath the truck and plugged it back in. I had my son turn the key on and off while I moved the float to different levels in order that it would register. It registered empty, 1/4/, 1/2, 3/4 and full just fine as I moved the float to those levels. If you leave the key in the run position and move the float, it won't register or better said, the in cab gauge will not adjust with the movement.
You have to turn the key off move the float and hold it there, then have your assistant turn the key on and the gauge will show the position that you've moved and held it at. I simply removed the plastic cover from the sending unit, and sprayed it down real good with electrical contact cleaner. I didn't scrub the copper contact area at all.
I was concerned that scrubbing might remove more than I wanted to, and really mess things up. I attached an Ohm meter and checked resistance thru out the float travel. All checked out good and I reinstalled it. So now my fuel gauge is working as it should be. I did make a video while I ohmed the Sender Unit thru it's travel, but for some reason it won't load.
[URL] ....
Ford 6.0L Power Stroke Diesel :: 2006 - Loosing Power Like Getting No Fuel And Died?
I have a 2006 F250 with a 6 liter diesel I got about a hundred sixty thousand miles on it I've had it bullet-proofed haven't had too many problems with it I thought the fuel pump went out yesterday so I replaced it drove fine for a few hours then it started losing power and like it wasn't getting fuel and died I got it home took a test light and check for power at the fuel pump I don't have any positive or negative power ran a hot wire and a ground straight from the battery and hooked it up to the pump and it worked but when I plug the factory wiring back into it and turn the key on I don't have any power I checked the fuses they're fine...
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Loosing Antifreeze About A Cup To Every Thousand Miles?
I am losing a small amount of antifreeze, about a cup every thousand miles, so I have to consistently add antifreeze. When i remove the oil fill cap, I have a small orange ring leading me to assume the loss is into the engine.
Dealer pressure tested system and told me everything was good, could not find a problem, which I think is likely not correct. How to proceed?
Ford 6.0L Power Stroke Diesel :: 2003 F350 Starting Loosing Power / Wouldn't Even Go Up To 15 Mph
I have a 2003 Ford F-350 super duty 6.0. A few weeks ago it starting loosing power, it wouldn't even go up to 15 mph. It now won't even move. There is 0 power. When I press the gas the motor bogs down to a very low idle and wants to die. I also had recent trouble with it starting. It would wind up to a very very low idle and about a minute later it would crank up to full idle. I changed the fuel filters (on top of the engine and under the cab) and also changed the fuel pump under the cab. After that I still have no power when pressing the gas it will still act like it wants to die.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Service Engine Soon Light - No Codes In Torque
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
Ford 7.3L Power Stroke (1999-2003) :: Idle Roughly - No Power - Got Codes P1280 And P1316?
Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 - Truck Lost Power Then Died - No Codes
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Fuel Leaking From Passenger Side Of Engine?
2003 Excursion 7.3
There is fuel leaking from somewhere on the passenger side of the engine.
What things should I be looking for? I'm thinking injector? Is it easy to identify and replace?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Shuddering - Diesel Fuel - Damage Engine?
02 7.3L SD Im on a long haul and think I might have bought some bad diesel. It is shuddering a little kind of like a miss. It started right after I stopped for fuel. Is this going to damage my engine to keep plugging along? Is it just going to run kind of rough until I burn up the bad fuel? Ive got about 200mi to go so just needed to know if its safe to keep driving or am I going to be stranded.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Injectors Clacking / Engine Feels Like Running Out Of Fuel
Engine felt like it was running out fuel, injectors were clacking. I got home put on AE and it has a low high open on the code reading. took valve cover off and plug came out. I did the quarter modification.
Anyway took the truck out a few days later truck drove ok when cold then after about an hour it lost power again and started clacking until it died out. I had to stop and let it cool off about 10 times before i made it home. I changed ICP sensor. took it out for ride and about ten minutes later same thing. I have to let oil temp get down to 165 before i can drive it again.
When i first drive it Icp pressure is about 500 at idle and 2650 at full throttle, that is until it starts clacking again and losing power then the engine wont take any throttle..and ICP duty cycle is at 26%... Would bad IPR do this??
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Accent LC (2000-05) :: Loosing Power And Could Not Accelerate As If Engine Was Not Getting Fuel
One morning I went to start my 2000 Accent, 1.5L Auto and the engine couldn't get going. I had road service come look at it and they said the problem was the fuel pump, I then got the car towed home. I changed the fuel pump and everything was working great again. I then changed the fuel filter, air filter, oil filter and flushed/refilled the oil. I used the car very lightly for a few days and had no problems.
Then yesterday I took the car about a 30 min drive, when on a main road my engine begun loosing power and I couldn't accelerate, as if the engine was not getting fuel. I managed to pull over safely and after about 30 mins of not getting anywhere I decided to hit around my fuel tank/pump with my club lock many times and what do you know the car starts and I manage to drive it about 25 mins, I was almost home when the same thing happened. I pulled over, waited, hit the tank and finally drove all the way home.
When I originally changed the fuel pump everything seemed fine, the plastic pump housing and everything attached to it appeared in great condition. So my hunch is that the problem would be where the fuel actually enters the engine block? The way that everything works fine until driving for roughly 25 mins makes me think the problem may be dependent on the temperature of the engine, given that's the main variable that changes?
Ford 7.3L Power Stroke (1999-2003) :: No Power / Zero Voltage To Fuel Pump
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
Ford 7.3L Power Stroke (1999-2003) :: No Power To Fuel Pump / Fuse 30?
I have a 2003 F250 and dont have power at fuel pump, or fuse #30. I put power directly to fuel pump and it worked and truck fired right up.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Low Power - Fuel Pressure?
Low power on my 2003 7.3 F350. The truck runs fine but I can tell it is low on power (seat of the pants). I figured it to be fuel related so changed fuel filter and oil with no change. When that didn't work I installed a fuel guage and this what I found. Key on no start fuel pressure 45 psi. Start truck the pressure will get up to 61psi. Under a load it will drop down to the low 30s. I have dropped the tank mixing chamber screens clean and so was the tank. Changed fuel pump and now under a load it drops to the high 30s. Does this sound like the fuel pressure regulator is leaking by and causing low pressure under a load? Truck is stock besides superchips 1705 programer.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Wire Burned In Half On Front Side Of Intercooler Plenum
I just noticed a wire burned in half on the front side of the intercooler plenum. See picture below,
Here is the left side showing the green wire stub going into the wiring harness on the front side of the intercooler plenum,
And this is the right side showing the wire going into the air intake duct between the turbo and the air filter,
I don't think it's been in this condition very long.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 - No Power Getting To Fuel Pump
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Started Losing Power Then Slowly Die / Fuel Pump Bad?
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke Blowing / Smells Like Fuel And Loses All Power
I am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?