Ford 7.3L Power Stroke (1999-2003) :: Injector Hold Down Bolts
Would it be a good idea to change the injector hold down bolts when I do the injector o-rings? They have never been out at 333,000 miles.
Plan on doing glow plugs, injector wiring, valve cover gasket's, intercooler pipes and the dreaded oil cooler.
Ford 7.3L Power Stroke (1999-2003) :: Injector Installation - Torque Hold Down Bolts
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
Ford 7.3L Power Stroke (1999-2003) :: Injector Hold Down Bolts Not Torque Down To Spec - Hard Starting?
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 RepliesFord 6.7L Power Stroke Diesel :: Truck Idle / Spool Up And Down When Just Sitting?
My truck when idling kind of spools up a little bit for a few seconds and then the turbo goes back down. sounds really cool actually. its been doing it since the truck was new, sounds like a plane engine shutting down. It does it over and over sometimes. I just deleted the dpf and unplugged egr last night and now i can really hear it! is this normal....
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Turbo Would Not Spool Until Revved The Engine Hard
It started after a blue spring upgrade. my turbo would not spool until we revved the engine hard then it kicked in and it's kinda worked since then.. it feels like the truck is struggling on acceleration and the boost builds fast up to 30lbs, the EBP seems to be stuck at 21.48psi until your in 3rd then it jumps and I have power again, also the turbo dumps (farts) if I let off even a little until the EBP jumps then no issues. I replaced the sensor and it's stuck at 21.48 all the time.
Now, I unplug it and it jumps between 26 and 28psi, plug in the old sensor while it's out laying on the motor (not installed) and right back to 21.48. I don't know where to go with this and it's my only truck so I need it running. also it was blowing the intercooler boot off at the turbo during a normal acceleration and the turbo spool has a howl to it when EBP is stuck...
Ford 7.3L Power Stroke (1999-2003) :: Bad Injector O Rings Cause Blow By And Oil Consumption?
I have a 2002 F350 7.3L w/superchips programmer, k+n cold air intake. Does NOT smoke a lot from tailpipe
Not running rough since I changed my oil to rotella 5w-40w synthetic.
Appears to have good amount of blow by coming from the oil fill when engine is warm.
Can Bad Injector O Ring(s) cause blow by and oil consumption?
Ford 6.7L Power Stroke Diesel :: DRW Tire Air Valves Access?
How do you access the tire air valves on the DRW, the inside tire valve? I can't get my air guage or my compressor air filling connection on the inside tire.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Runs Bad After Diesel 911 Injector Cleaner
I filled up at the same fuel station I've filled up at for 6 months, never had a problem. I just bought a 6 liter and put some injector cleaner in on the last fill up. Ever since then, it's been running really rough and missing when cold, and even when it's warm if I really lay into it, it'll pop and sputter. The fuel in water lights been on since I bought it. I think I have a bad sensor, because it was running fine until I put that cleaner in. Since its been running rough I put in new fuel filters and drained the fuel water separator, which only had fuel in it. I don't really know what it could be, but I'm 99% sure it's an injector issue since it started only after I put fuel treatment in.
View 8 RepliesFord 6.0L Power Stroke Diesel :: Cannot Get Exhaust Manifold Bolts Off
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Small Power Steering Leak Where Master Cylinder Bolts Onto Hydroboost
2007 F350... I noticed I have a small power steering leak where the master cylinder bolts onto the hydroboost. Is there a o-ring or seal between the two? or do I have to replace the hydroboost? Been looking online for a schematic but can't seem to find one.
View 13 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Oil Pan Leaking Around The Edge And One Of The Bolts
Went in today and the Service advisor said the oil pan was leaking around the edge of the pan and one of the bolts. He stated he ordered a new oil pan and referred to it as a "new design". I asked him what the "new design" was and he had no idea. Didn't know if it was a metal pan like the newer trucks or if it was another plastic one. Looking for oil pan replacment by Ford and is it the newer metal one or another plastic one ??
View 10 RepliesFord 6.0L Power Stroke Diesel :: Part Number For High Pressure Oil Rail Check Valves
What is the part number for the high pressure oil rail check valves for a 2003 6.0L? I'm referring to the ones that screw into the oil rail. I would like to avoid the local dealer if possible.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - Taking Out Turbo Bolts?
I for the life of me can not even see the bolts to take them off.
2006 F350 4X4
Ford 6.0L Power Stroke Diesel :: Injector #7 Misfiring?
I've got an injector #7 misfire, so it looks like I'll be replacing my first stick since the warranty expired.
Does the injector from Ford come with the copper crush washer? Will I need to buy anything else except for the oring kit?
where is injector 7? edit: it looks like number 7 is the farthest back on the passenger side. Great! I get to do the hard side.
AE pics below. I've never understood the Power Balance test, it most always looks the same. Seems to me something should look odd with #7, but I'm just not seeing it. As I shut down each cylinder one at a time, all made the engine run noticeably rougher, except it was only a subtle difference when shutting down #7. So that plus the code pointing at #7 lead me to believe that #7 is my culprit.
Ford 6.0L Power Stroke Diesel :: Crank Pulley / Harmonic Balancer Bolts - Replacement?
I am reviewing the ford assembly instructions before I put my engine back together and noted that it indicates that the balancer bolts are torque to yield. I thought it odd but is it really necessary to replace these? Is it done in practice?
View 1 RepliesFord 6.0L Power Stroke Diesel :: Bolts Holding Exhaust Heat Shroud Behind HPOP
There are two bosses on back of hpop cover that have bolts holding heat shroud for the exhaust. How difficult are these to remove? The drivers side looks fairly accessible, but passenger side I am not too sure of. I will be back to disassembling everything in a couple of days, and just getting a heads up on it.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Lack Of Power / Replaced Injector Now Won't Start
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Brief Loss Of Power When Accelerate While Driving - Bad Injector?
Occasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677