Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Bolts Holding Exhaust Heat Shroud Behind HPOP
There are two bosses on back of hpop cover that have bolts holding heat shroud for the exhaust. How difficult are these to remove? The drivers side looks fairly accessible, but passenger side I am not too sure of. I will be back to disassembling everything in a couple of days, and just getting a heads up on it.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Changing Right Exhaust Manifold?
How difficult is it to change the passenger exhaust manifold? I have just finished replacing the left exhaust manifold. The biggest issue was rusted fasteners and inexperience. Have torches. Any you tube videos show the left manifold being changed but not the right. I do not have a hoist and work in my driveway. Is the right side more difficult and should I leave it to someone with a hoist?
View 4 RepliesFord Exhaust :: Exhaust Manifold Leak Due To Broken Rusted Bolts
I have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 RepliesFord F-150 - 1997-2003 :: Exhaust Leak On Passenger Side / Broken Exhaust Manifold Bolts
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesFord 6.0L Power Stroke Diesel :: Coolant In Driver Side Exhaust Manifold
So ford is replacing 8 injectors for me and they found this. They are trying to tell me bad oil cooler but I do not believe it. What do you all think is the cause. I should also say that I had coolant in my drivers side exhaust manifold.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Left Hand Exhaust Manifold Replacement
Attempting to take this on myself. My passenger side manifold was replaced a year ago.....BTW This damn truck - all stock - no modifications of any kind - just turned 100k miles. One owner - me.
So I have removed everything I think I need to to gain reasonable access including the fenderwell and all the intake tubes and battery and coolant reservoir. I want to use some heat and try not to break the bolts but there is a thin wiring harness just above the exhaust manifold. I can't find it in any diagrams on the ford parts site. It looks like the glow plug and injector harnesses are up above near the intake manifold but this one is down below all that. It connects to small rubber thing - 1 for each cylinder. There is nothing else electrical near it - everything else is up top.
Now my rant - look away if you are a die hard ford truck fan or 6.0L powerstroke fan.
So far I've had to replace both exhaust manifolds because they burned and rusted right through. New transmission cooler lines -yes - rusted through and cooler (because we couldn't get the lines off without destroying the cooler). Cat got clogged (that was fun to find and fix). All 4 front ball joints replaced. Transmission dip stick tube rusted through. Several brake lines had to be replaced due to rust. The air conditioner quit with about 80k miles. I haven't fixed that yet. My oil pan is rusting through and needs replacement. Friggin oil pan! I have never in my long life experienced that. I know of other diesel pickups that are older with far more miles that live in the northeast, used for plowing and never garaged that don't have their oil pans rusting through. Just had to change both power steering lines that go to the gearbox due to leak caused by rusting through. EGR needs to be cleaned or replaced almost as often as the oil need changing. This POS needs to be out of my life!
Too bad because if it was dependable and wasn't made out of the cheapest crappy metal Ford could find it would be a great truck. Rides and hauls great. Plows great. Good looking truck, too. Standard cab 8 foot bed. Dark green. Just can't keep doing this.
Ford 6.0L Power Stroke Diesel :: Exhaust Manifold Leak - Sounds Like Air Rushing Out From Driver Side Of Engine
So I started my truck this morning and it sounds like air rushing out from the driver side of the engine. I currently have my ICP unplugged due to a bad sensor, will be replacing it on Sat. Also I have been having an issue with my turbo but I don't think that it's related as I here the air rushing sound when at idle as well at when driving. It seems to be a bit louder when the engine is cold but I could also be crazy about that.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Manifold To Up-Pipe Bolts Seized
So I had recently developed a leak in the up pipes behind the collector. Big surprise, right?
Well, a 6-point socket was spinning on the collector bolts (probably from rust) so I decided to cut the manifold to up pipe bolts. Got the up pipes off/out. Well after and <acronym title="Manifold Absolute Pressure">MAP</acronym> gas torch, I can't punch ANY of the bolts out.
There is little to no room to get to the bolts. (I have the down pipe removed.) At this point I'll try a few more doses of hot wrench and PB Blaster, but if I have to do the manifolds I'll just pull the engine, since chances are there will be at least one stuck bolt there, too. I really don't want to go that, but eventually I'll need to install my new oil pan anyway.
Ford F-150 (2004-2008) :: Manifold Exhaust Leak - Rusted Bolts
Truck has 107 thousand miles; had to take it in for an manifold exhaust leak. Mechanic said bolts are so rusted they break.
1) was there ever a ALERT from ford about these bolt's?
2) Thought i read ford had stainless bolts for this problem...
I've had F150's only since the mid 70's and this 04 has cost me more in repairs than ANY previous F150..
Ford F-150 - 1997-2003 :: F350 - Exhaust Manifold And Two Of Lower Intake Bolts Broken
I have a 97 f350 crew cab xl stock everything. 351 windsor in it I do believe. as of right now He is broken down pulled apart in my garage. Due to a much requested headgasket replacement. In any event long story short I got him all apart to discover that there was someone in it before me & had broken the infamous exhaust manifold bolts (5) and two of the lower intake bolts, (of course I've tried the correct route in removing these broken bolts/studs but again the year of the truck (1997) & its bone stock no way their moving...
So of course I tried the next best thing (on a budget) which is to drill them out, but I went to far into the exhaust manifold bolt holes, And now I believe that I've ruined the heads is this so? If so who knows where i can get a decent set of bolt on heads ready to go. yes this is my daily driver & since He's been down I've been going deeper in dept.
Ford Super Duty (1999-2016) :: F350 V10 - Exhaust Manifold Bolts Breaking
Bolts breaking on the exhaust manifold. If so why isn't ford doing a recall on this problem I have a F350 V10 90K miles and 3 on the top drivers side are missing not sure on the passenger side. Is this a problem with all the ford engines I have never had this problem with any other truck or car I have owned.
View 5 RepliesFord Super Duty (1999-2016) :: Broken Exhaust Manifold Bolts - Long Term Fix?
I've got the dreaded broken exhaust manifold studs on my 2004 F250 V10. I don't drive it much (just 50,000 miles in 10 years) and confess I've ignored the hissing for quite a while. Is there really a permanent fix for these broken studs? Or should I expect to be replacing broken studs every 2 or 3 years?
If there is a permanent fix what is it? Special studs? Special manifold? I want to keep this truck a long time and don't want to be replacing these studs every few years.
Ford Super Duty (1999-2016) :: 2008 F450 - Lost Both Turbos / Exhaust Manifold Bolts Broken
Our F-450 with 102000 miles lost both turbos also broken exhaust manifold bolts. This truck carries tools fuel tank and sometimes skid loader on trailer. Heard lots of bad things about 6.4 liter motor now first hand experience. Asked dealer if 6500.00 bill could be reduced since so close to 100000 mile warranty and was told nothing could be done. Can not afford to sell truck now also have two other Ford F-250s newest one 2012. Is there any other approach that could be taken to get some relief from this expense.
View 14 RepliesChevrolet - Silverado1500 :: 2003 - Exhaust Fumes Malfunction - 3 Head Bolts On The Manifold Popped Off
I have a problem with exhaust fumes in my 2003 Silverado truck. Initially, 3 head bolts on the manifold were found to be popped off. After replacing the bolts, the exhaust fumes in the cab still existed. The truck has been evaluated by a Cherolet dealership and 2 independent garages who found no system exhaust leaks. Obviously, I am very frustrated and not sure what to do next or where to go.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Leak From Exhaust Manifold
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
Ford 7.3L Power Stroke (1999-2003) :: Broken Exhaust Manifold Bolt
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Removal - 1 Bolt Stuck?
I managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Broke Off Bolt In Exhaust Manifold To Head
Well i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.