Ford 7.3L Power Stroke (1999-2003) :: Injector Installation - Torque Hold Down Bolts
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
Ford 7.3L Power Stroke (1999-2003) :: Injector Hold Down Bolts Not Torque Down To Spec - Hard Starting?
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 RepliesFord 6.0L Power Stroke Diesel :: Injector Spool Valves Blow Off Bodies - Broken Bolts
While diagnosing a low power and misfire condition on my 04.5, I was measuring coil resistance at the injector connectors. Found 1,3,7 had open circuits for one of the solenoids. 3 bad injector coils and no codes, no contribution codes... Why?
Anyway, pulled it apart to find the spool valves of 1 and 3 came out with the oil log the small bolts that hold them to the bodies had broken off. #7 only 1 bolt had broken off and the other was there but loose.
I got this truck with no history, and Had a variety of issues, like a bad fuse box that caused a no start, massive amounts of water in the fuel, and it had sat for 6 months untouched before I got it. I took care of the previous problems search for my previous posts if interested.
So what caused the spool valve to get blown off the bodies? I'm not sure if these have been rebuilt or ever removed, truck has 135 k. Could it be the water in the fuel that seized the intensifier piston?
Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Bolts Broken?
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Manifold To Up-Pipe Bolts Seized
So I had recently developed a leak in the up pipes behind the collector. Big surprise, right?
Well, a 6-point socket was spinning on the collector bolts (probably from rust) so I decided to cut the manifold to up pipe bolts. Got the up pipes off/out. Well after and <acronym title="Manifold Absolute Pressure">MAP</acronym> gas torch, I can't punch ANY of the bolts out.
There is little to no room to get to the bolts. (I have the down pipe removed.) At this point I'll try a few more doses of hot wrench and PB Blaster, but if I have to do the manifolds I'll just pull the engine, since chances are there will be at least one stuck bolt there, too. I really don't want to go that, but eventually I'll need to install my new oil pan anyway.
Ford 7.3L Power Stroke (1999-2003) :: Rounded Off Thermostat Housing Bolts
Tried to flush it and got as far as draining everything. I can't hook up my T and begin the flushing process because I can't remove the thermostat. I have a buddy who can get the bolt out but I'd have to be able to drive the truck to him. I've tried just about everything to remove it. I did manage to find some replacements for when I do get the last one out though .Is there a way to still flush this thing like maybe just hook up the hose to the t and run the engine with the heat on to open the thermostat?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - Power Loss / Hard To Hold The Speed?
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
Ford 7.3L Power Stroke (1999-2003) :: Replacing Injector Cup?
im in the process of replacing the injector cups and i knew this would happen since the whole process went way to easy up until this part. I am using Clays remover kit and it will not remove the cup. I do it according to the book and it just keeps popping out of the cup when i try to remove
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Bad Injector Sound?
Now ive got a tick tick tick tick sound from the engine. The tick increases and decreases with rpm and is present at idle. If it were a gasser i would say a lifter, honestly it kinda reminds me of a sewing machine lol.
Whatever it is as long as its not serious and my engine is solid im ok w it, I bought this truck knowing I was going to have to put work into it, I just didn't know work was going to go fall one after the other week by week from the day I got it....the previous owner must really have neglected this thing....
Hard to hear it over the sound of the engine, but its there, and is slowly getting worse
[URL]
Ford 7.3L Power Stroke (1999-2003) :: Coolant Seen While Injector Out?
Although not certain, I *thought* I saw coolant run into the front drivers side injector hole when the injector was out and I leaned on the radiator hose. I had knowledge t pull them and changing the orings who were initially concerned then not concerned after looking closer.
Either I made a mistake in what I thought I saw on my first experience with injectors, or there really is a problem that I didn't know enough about to address at the time. So I opened this thread to get more info and stop hijacking 67speeda's thread, found here: [URL] ....
As per recommendations, I will check my coolant bottle for any fuel, oil, residue, etc. I am also going to reach out to my buddies and see if they saw a problem with coolant, too, or they realized it wasn't coolant and I didn't take note of it ...
It was a REALLY LONG day and my ability to concentrate had begun to slip quickly (health issues), so it's possible I missed something there. So IF I saw coolant going into that cylinder with the injector removed, how bad would that be? I thought it came from pretty high up and ran down where the injector sits..
Ford 7.3L Power Stroke (1999-2003) :: Turbo To Pedestal Bolts Really Hard To Break Loose
Are we supposed to put anti sieze on the turbo to pedestal bolts. They were really hard to break loose when I pulled it Cheater bar tight. 18 ft. lbs sound right ?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Engine Lost Power - Injector Harness?
So after hitting a pothole, it would seem like half the engine lost power, after some searching around, i found that i would most likely be the harness inside the valve cover that has lost connection.
Its the right side, so i would need to take of the turbo pipe, and probably something else to get to it.
Since i'm doing this job, what to check out along the way? I want my 7.3 to be as reliable as possible.
I will probably ask some questions along the way, it can be a challenge sometimes to own a car that not many mechanics are familiar with, but as i have read online, this should be a very straight forward fix.
Can the harness be upgraded so it doesn't happen again? Its an 02
Ford 7.3L Power Stroke (1999-2003) :: F350 Will Hold Back Sometimes And Not Increase Speed
I am having trouble with my 1999 F350 Ford Powerstroke, Looses power but the motor never quits and also starts up fine, will set and run and warm up on the coldest morningIdles fine, It will hold back sometimes and not increase speed. I can take it out today and it may be fine and tomorrow can't run 2 miles. I was thinking CPS but after reading information I am not sure. What may be causing this issue. I just put a High Pressure oil pump on it could this have anything to do with it. Was not having a problem before the pump was changed. The pickup has 190,000 on it actual miles.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Zf6 Clutch Options That Will Hold 550hp At The Wheels
So I have the luk full ceramic clutch now, this is my second one (about every year it needs replaced) and it's getting close to needing a new clutch again. Right now my 7.3 is sitting at 442hp and 864 TQ. Im Building a forged rod motor with the idea of getting 5-550 HP to the wheels out of it and hitting the 1000 TQ mark. What clutch will hold that and not chatter and try to knock my teeth out like my current clutch. The closer to a stock clutch engagement feel the better, I hate backing up or starting out with a load more than 10k (I have to start in low, or 4wd low to backup). Truck is a 01 crew cab, on 35's stock gears may be going to a 6" and 37's in the future but that's it.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: Injector 5 High - Low Error After New IDM
Story starts when I was cruising down the freeway and the truck cut out, seemed like a CPS or Injector related issue - seemed like a whole cylinder bank cut out. Stopped truck on shoulder, she shuttered and died. Turned truck off and restarted, ran like a top for about 4 miles then did the same again. I restarted it again and drive it straight home, ran like it I usually did.
As soon as I arrived home I did a little research and learned to start with CPS. I replaced my grey CPS with a new, Ford grey CPS. Truck fired up, ran the same that it did before - not the best idle but at 302k I was content. Drove it for a few days and it did it again, hobbled the truck home, although it did do it a few times and the last time it did it was really hard to start.
I replaced the IDM through NAPA. She's a work truck so I wasn't going to splurge for a Swamp Unit, the NAPA one came with an 18-Month Warrenty. She started right up afterward, the smoothest idle I had ever felt and she ran great, except for an SES. I ran the code and it was an IDM code, ran a buzz test and it pulled injector #5 high/low error, but it buzzed (a bit quieter than the others).
Here's the weirdest part, when the motor is cold the SES is constant, but as it warms up it only shows under power and sometimes flashes off at certain RPMs (1700-1900 and 2100-2300) and turns off when engine braking (TC locked) returns at idle. NO engine lights with the old IDM. I've checked the wiring to the injector from the 42-pin to the outer connector. (.6-.7 ohms, what my meter reads without any loads) Injector (from outer connector) reads 3.2 ohms. UVCH is less then 2 months old (GP issues) injectors have less than 5k on them.
Why? New injector solenoid? Bad IDM? Is it possible my last one never fired #5 and it got stuck? Or did my old IDM fry #5? Also I'm going to keep driving it and maybe it'll clear up, there was one drive I took where it cleared up completely. I've done some extensive research on this an i'm stumped. With the new IDM the truck has run better then it ever has.
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Replacing Injector?
I have an 01 F-250 Powerstroke. It has been shaking terribly at around 1500 rpms and shutters while holding the brake and increasing engine speed. I took it to the dealer and they told me that my #1 injector is bad. I decided to check around a little bit. I found a diesel service dealer that has brand new injectors. (Not rebuilts). Anyway I would like to attempt to install this injector myself.
1. Which injector is #1? (I've done a lot of mechanic work but not a whole lot on engines.)
2. What do you do with the fuel and oil that get into the cylinder? Do you have to get it sucked out?
3. Anything else that is crucial? What do you have to torque the injector bolt to?
Ford 7.3L Power Stroke (1999-2003) :: Replacing Injectors - Which Injector Goes Where
I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Tool For Replacement Of Injector Cup?
Rebuilding my 7.3 and I'm in need of the removal and install tool for the injector sleeves/cups for the 7.3 Powerstroke Diesel.
I'll pay all shipping charges and a small fee if required. I hate purchasing a tool I'll never need again, rather better not need.
Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.