Ford 6.0L Power Stroke Diesel :: No Start No Crank / Code P2285
So I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).
Ford 6.0L Power Stroke Diesel :: Hot Crank No Start / Code P2285
So my 04 f350 was running fine good power and everything till I shut it off a couple days ago and now when it is cold it fires right up but when the truck warms up it just cranks and cranks .... only code I throwing is p2285
Key on engine off
Ipr-14.8
Icp-0
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine running
Ipr-33.5
Ficm main power-48.0
Ficm logistics-12.5
Icp-875
I thought I fixed it before but I was sadly mistaken replaced the ICP and IPR...
Ford 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2007 F350 Won't Start - Code P2285?
i have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Hard Start - CEL On - Code P2285?
Truck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.
First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.
Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.
I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.
Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?
Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?
Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?
Ford 6.0L Power Stroke Diesel :: 2003 - Crank No Start - Code P2285 ICP Low Circuit
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
Ford 6.0L Power Stroke Diesel :: Running Rough - CEL On With Code P2285
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
Ford 6.0L Power Stroke Diesel :: Where Is ICP Sensor Located - Code P2285
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Cylinder 5 Misfire Code P2285
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
Ford 6.0L Power Stroke Diesel :: Stuck Turbo And High Deltas - Code P2284 / P2285
Stuck turbo and high deltas so I replaced the oil cooler, coolant, thermostat, rebuilt turbo. Etc etc. Now I'm getting p2284/p2285 intermittently. Upon inspection ICP looks great at idle and 2500. IPR at hot idle is 20.9 but when you run it up to 2500, it drops to 14.7 and after a few seconds hpop at idle jumps to 875 and I get the p2284/2285. Bad IPR?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Engine Light On And Code P2285 - Injector Control Pressure Sensor Circuit Low
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Van Would Not Start Just Cranked
Came out of the building center yesterday after about ten minutes, and the van wouldn't start. Just cranked and cranked.
So I fired up Torque Pro and the HPO only got to 156.8psi. The idiot gauge came up to where it should be.
The dipstick looks good. I unhooked the ICP sensor and still no go. Reconnected.....
So I called a tow... after It cooled down.(75*F water) I tried again and got up to 295psi, but still not enough to start.
At this point I know I have recent injectors and updated Plug& pipe on the passenger side, a new IPR, and (another) new STC fitting.
I will get the air to it, and investigate, but at this point,I am leaning towards the Dummy Plug on the drivers side. Or maybe I am just hopeful because the internet says that one can remove the VC on that side fairly easily.....(Van Body)
However I did recently(2K miles/??) have the engine apart to get at the HPOP and STC leak issue I had. In the event of a possible stuck IPR- what would be the symptoms during an air test? No change with power applied? Or should I just remove and inspect?
Ford 6.0L Power Stroke Diesel :: Cranked For About 15 Seconds With No Start
This morning I went out to start my truck. It cranked for about 15 seconds with no start. I set my TorquePro to monitor the IPR% and cranked again for about 10 seconds. The IPR% was about 83.7% with no start again. I went inside and searched for "crank no start" threads to see what else I needed to look at. I went back out and added HPOP to the TorquePro. Cranked for about 5 seconds, thinking I would get no start again, but it fired up. After start I was getting about 27% on the IPR and abour 537 on the HPOP. Drove to work with no problem.
Could this just be a fluke, or do I need to be concerned about it? I have a road trip coming up to Tennessee on Thursday. I did standpipes, dummy plugs, STC fittings, EGR delete, new oil cooler and upgrade to stainless steel IPR screen about a year ago.
Ford 6.0L Power Stroke Diesel :: 2003 Excursion Just Cranked But Won't Start
My truck started and ran as it always did and about a mile it just quit. I tried to restart it and it just cranked but wont start. I bought a scangauge II and did test for the normal no start issues that Ron on you tube mentioned.
Values are as followed engine off
14.8 - IPR 0- SYC
48.0 FMP 28 - ICP - I was thinking that the ICP sensor was a newer 04 model so the values come back a little higher.
While Cranking its as follows
84.7 - IPR 1- SYC
48.0 FMP 46- ICP
Research says that I think if the IPR is bad or unplugged it could show a low value on the ICP..
Also I wanted to check both the IPR and the ICP for connection and to make sure no oil on connectors. See if the IPR screen was cracked or cut.
I have tried to find them and cant so I thought they were behind the turbo so we took that off and no i still cant find it. I have the truck apart and it got late so I have decided to take a break and come back to it tomorrow.
As I said I'm not a diesel mech but I'm pretty good with figuring things out or at least enough to get into trouble.
Ford 6.0L Power Stroke Diesel :: Cranked Multiple Times / Hot No Start
Had a hot no start going, found dummy plug issue, replaced dummy plugs. While in there I cleaned the injectors (passenger side only) and put back together. Cranked multiple times, had to recharge batteries a few times as it is in the 10 - 20 degree temp range. No joy on re-start following the work.
Numbers I'm getting are:
KOEO With ICP connected:
ICP - 0
ICV - .07
IPR - 14.8
While cranking
ICP - eventually builds to 400+-
ICV - eventually increases to .13
IPR - maxed at 84.7
ICV too low so...
After disconnecting ICP
KOEO
ICP - 0
ICV - 0 (disconnected)
IPR - 14.8
While cranking
ICP - up to 1693
IPR - to 65.5
Still no start.
Ran through FICM check and the numbers are fine - 48 key on, 47 key during buzz, 47-48 while cranking.
I do get oil pressure registering on the dash gauge.
Fuel is in the filter housing
Oil filter housing refills with oil as expected when cranking
Only code is the P2285 once the ICP is disconnected
Ford 6.7L Power Stroke Diesel :: 2011 F550 - Code P0299 / Faint Ticking Like A Stone In The Tire
What to do 2011 F550 RampTruck 11,850 miles on it the vehicle has been back to the dealer 5 times for the same trouble code P0299. After the last time it was in they had it for 2 weeks seemed to be fixed. Last week one of my drivers was towing a Chevy S10 50 or so miles and heard a very faint ticking like a stone in the tire that got instantly worse and before he could pull over started rapping and stalled out. We towed it back to the dealer they removed the Cab disassembled the engine and found a "blown piston" is there quote. What should we do about this problem the dealer is supposedly fighting with Ford and Ford doesn't want to put in a new engine.They want to fix it instead....
View 12 RepliesFord 6.0L Power Stroke Diesel :: 2005 Won't Start - Code P0401 And P0672 Shows Up?
2005 PSD Ex. 4x4.
Drove it a few nights ago and it felt really gutless. Next morning, no start. Well, it tried, but it sounded like it was run out of fuel (had half a tank)and I turned it off. Changed both fuel filters, key on / key off to purge system about 2 dozen times. Still no start.
I have all eight injectors with "injector Circuit Low" code, a P0401 - Exhaust Gas ReCir Flow Insufficient Detected, and P0672 - Glow Plug #2 (which it has had for a few months).
I thought with all of the injectors, it might be the FICM, checked the FICM voltage with Torque during a start and it showed 47V the whole time.
Harness? I did not think running with the glow plug error would be a big deal especially during the summer in So Cal.
Ford 6.7L Power Stroke Diesel :: 2015 F550 - CEL Code Oxygen Sensor Performance Bank One Sensor One
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesFord 6.7L Power Stroke Diesel :: Strong Exhaust Smell On Cold Start?
We've had a run of -20 to -40 weather here for the past few weeks.
A few weeks back I noticed that when I climbed into my truck after command-start warm up for 10 minutes, and I could smell strong exhaust.
I figured it was hopefully the wind, or an isolated event.
Over the past few weeks I've used my truck for 3-4 more around town runs and every time I warm it up I get the strong exhaust smell. It's that rich, eye watering, sickening exhaust smell. I also notice a small yellow frozen puddle under the exhaust tips that wasn't there before.
It's bad in the cab, but even walking around outside the truck and the smell is sickening. I actually just started the truck and I could actually smell the exhaust smell faintly, from inside my house! This has never before occurred. Prior to this, a person could hardly tell it was a diesel by the smell of the exhaust.
Once the truck is up to temperature the smell seems to disappear, or at least lessen.