Ford 6.0L Power Stroke Diesel :: No Start No Crank / Code P2285
So I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).
Ford 6.0L Power Stroke Diesel :: Hot Crank No Start / Code P2285
So my 04 f350 was running fine good power and everything till I shut it off a couple days ago and now when it is cold it fires right up but when the truck warms up it just cranks and cranks .... only code I throwing is p2285
Key on engine off
Ipr-14.8
Icp-0
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine running
Ipr-33.5
Ficm main power-48.0
Ficm logistics-12.5
Icp-875
I thought I fixed it before but I was sadly mistaken replaced the ICP and IPR...
Ford 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Hard Start - CEL On - Code P2285?
Truck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.
First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.
Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.
I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.
Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?
Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?
Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?
Ford 6.0L Power Stroke Diesel :: 2003 - Crank No Start - Code P2285 ICP Low Circuit
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
Ford 6.0L Power Stroke Diesel :: 2005 F550 Cranked Strong But No Start - P2285 Code
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Running Rough - CEL On With Code P2285
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
Ford 6.0L Power Stroke Diesel :: Where Is ICP Sensor Located - Code P2285
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Cylinder 5 Misfire Code P2285
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
Ford 6.0L Power Stroke Diesel :: Stuck Turbo And High Deltas - Code P2284 / P2285
Stuck turbo and high deltas so I replaced the oil cooler, coolant, thermostat, rebuilt turbo. Etc etc. Now I'm getting p2284/p2285 intermittently. Upon inspection ICP looks great at idle and 2500. IPR at hot idle is 20.9 but when you run it up to 2500, it drops to 14.7 and after a few seconds hpop at idle jumps to 875 and I get the p2284/2285. Bad IPR?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Engine Light On And Code P2285 - Injector Control Pressure Sensor Circuit Low
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2007 F350 - No Throttle Response - Code PO231
2007 F350 6.0L 230,000 miles
Yesterday, while driving home from a weekend out of town trip, all of sudden lost throttle control. Just went to idle while at cruise speeds, could pump pedal and no response. Then got pedal control back and seemed to run normally.
This happened several times. Hubby suggested moving the adjustable pedal which I did slightly. Although I was not using the cruise control, we had a sense that maybe it was engaging??? So I hit the off button a couple of times. After these two interventions, drove the last 80 miles home with no further incidents.
Today, we checked codes and had a PO231, Fuel Pump Secondary Circuit Low. I don't think that is our problem with above based on research, but we will look into fixing that too. We are thinking TPS or a position sensor on the accelerator pedal. We could replace those easily ourselves.
Ford 6.0L Power Stroke Diesel :: 2004 F350 Won't Start / CMP Sensor Code
2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
Ford 6.0L Power Stroke Diesel :: 2007 F350 DRW - Cold Start Hesitation No DTC / CEL
Recently I replaced the unison ring on my turbo, EBP sensor and cleaned carbon out EBP tube/upper part of motor. After doing so she seemed to run fine but not like I remember when I first got her. Plenty of power but ever so slightly off, only an owner would notice. Few weeks later she hesitates a little bit while she's cold in the morning. I let her run 3-5 minutes b4 actually driving but as u know it's a little while to get up to operating temp. Temps seem OK 190-200 EOT/ECT. Fresh oil/filter, air filter, coolant, EGR was cleaned out a little while back and EGR valve replaced 25k ago. I'm not sure where to look at this point...the motor has about 30k on it.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Codes P2285 And P2287 - ICP Circuit Low And Intermittent
The other day my 07 power troke threw codes p2285 and p2287- ICP circuit low and ICP circuit intermittent. The trucks idle was revving up or bouncing around every so often, not consistently.
I did a visual inspection of both the sensor and pigtail checking for oil but it looks to me like everything is clean and oil free (see pictures). When I unplugged the connector the trucks idol smoothed out and everything ran great!
My questions is what does this indicate? Does this mean my ICP sensor is bad, my pigtail is bad, or there is a short in the harness somewhere?
Ford 6.7L Power Stroke Diesel :: 2011 F350 - Reduced Engine Power Code On Dashboard
I have a 2011 6.7 F-350 Diesel. I bought the truck new and I've never had any problems with it until now. I have a SCT Chip & Tuner. It needed an update so I returned the truck to stock and a code came up on my dashboard that said "reduced engine power" which obviously I thought was Normal because of the modifications done to my truck.
I updated my tuner and returned the truck to a performance tune but this dashboard code will not go away. My truck isn't reading any codes and there's no other indication lights on. The truck has Normal RPM readings but 0 throttle response. No power at all...
Ford 6.0L Power Stroke Diesel :: 2006 F350 - CEL Code For Injector Voltage Being Low
I have a 2006 F-350 4x4 CC LB. I recently had my check engine light come on coincidentally on my way to the auto parts store. Asked them to plug in the scanner and read the code. It had around 20! This truck has 40000 miles on it. All of the codes were dealing with injector voltage being low. All eight cylinders. So I'm thinking ficm is going out. I replaced the batteries shortly after this. I driven it a time or two after this and it started cutting in an out going down the road. Seemed down a few cylinders for a few seconds and pouring black smoke from the tailpipe of a stick truck. Made it home after it did this there times. Stated it up to move it a few days ago. Some white smoke that clears quickly and ran rough for a few, pulled it in gear surged forward and died. I cleaned the EGR valve and re o ringed it. Tested the drivers side pin on the FICM and have 47-48 volts with key on and cranking.
View 4 RepliesFord 6.7L Power Stroke Diesel :: 2013 F350 - CEL Coming On - Code P054F
I have 2013 f350 crew lariat 4x4 6.7 5000 miles . Cel coming on about 300 miles apart , 4th time now same code p054f ,dealer ship has no answers. Thayer say ford is investigating it ?? I don't about that but it is a real pain bringing it in.
View 1 RepliesFord 6.7L Power Stroke Diesel :: 2011 F350 - Engine Code P0299
2011 Ford f350 6.7 diesel ... Is this a problem we need to have fixed?
View 2 Replies