Ford 6.0L Power Stroke Diesel :: Cranked For About 15 Seconds With No Start
This morning I went out to start my truck. It cranked for about 15 seconds with no start. I set my TorquePro to monitor the IPR% and cranked again for about 10 seconds. The IPR% was about 83.7% with no start again. I went inside and searched for "crank no start" threads to see what else I needed to look at. I went back out and added HPOP to the TorquePro. Cranked for about 5 seconds, thinking I would get no start again, but it fired up. After start I was getting about 27% on the IPR and abour 537 on the HPOP. Drove to work with no problem.
Could this just be a fluke, or do I need to be concerned about it? I have a road trip coming up to Tennessee on Thursday. I did standpipes, dummy plugs, STC fittings, EGR delete, new oil cooler and upgrade to stainless steel IPR screen about a year ago.
Ford 6.0L Power Stroke Diesel :: 2003 Excursion Just Cranked But Won't Start
My truck started and ran as it always did and about a mile it just quit. I tried to restart it and it just cranked but wont start. I bought a scangauge II and did test for the normal no start issues that Ron on you tube mentioned.
Values are as followed engine off
14.8 - IPR 0- SYC
48.0 FMP 28 - ICP - I was thinking that the ICP sensor was a newer 04 model so the values come back a little higher.
While Cranking its as follows
84.7 - IPR 1- SYC
48.0 FMP 46- ICP
Research says that I think if the IPR is bad or unplugged it could show a low value on the ICP..
Also I wanted to check both the IPR and the ICP for connection and to make sure no oil on connectors. See if the IPR screen was cracked or cut.
I have tried to find them and cant so I thought they were behind the turbo so we took that off and no i still cant find it. I have the truck apart and it got late so I have decided to take a break and come back to it tomorrow.
As I said I'm not a diesel mech but I'm pretty good with figuring things out or at least enough to get into trouble.
Ford 6.0L Power Stroke Diesel :: Cranked Multiple Times / Hot No Start
Had a hot no start going, found dummy plug issue, replaced dummy plugs. While in there I cleaned the injectors (passenger side only) and put back together. Cranked multiple times, had to recharge batteries a few times as it is in the 10 - 20 degree temp range. No joy on re-start following the work.
Numbers I'm getting are:
KOEO With ICP connected:
ICP - 0
ICV - .07
IPR - 14.8
While cranking
ICP - eventually builds to 400+-
ICV - eventually increases to .13
IPR - maxed at 84.7
ICV too low so...
After disconnecting ICP
KOEO
ICP - 0
ICV - 0 (disconnected)
IPR - 14.8
While cranking
ICP - up to 1693
IPR - to 65.5
Still no start.
Ran through FICM check and the numbers are fine - 48 key on, 47 key during buzz, 47-48 while cranking.
I do get oil pressure registering on the dash gauge.
Fuel is in the filter housing
Oil filter housing refills with oil as expected when cranking
Only code is the P2285 once the ICP is disconnected
Ford 6.0L Power Stroke Diesel :: 2005 F550 Cranked Strong But No Start - P2285 Code
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Cranked For Few Seconds Then Dies?
My truck will only stay cranked a few seconds then dies, I have a lot of codes popping up! I was told may be the FICM.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Won't Crank Sometimes But Cranked Right Up If Use The Yellow / Blue Wire
About a month ago my 2005 Ford Excursion 6.0 wouldn't crank. Everything came on fine and there was no sign of a problem. when I tried to crank it nothing happened. I read about the yellow/blue wire on the passenger side and tried that. It cranked right up, and then worked fine with the key. No other problems until today. Same thing happened again. What could this be?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranked For About 10 / 15 Seconds Before It Sputtered And Tried To Start But Quit
A lady friend of mine got a '99 7.3 CCLB auto dually in a divorce. She doesn't drive it but starts it once a week and yesterday it wouldn't start. It cranked about 10/15sec (after waiting for WTS light to go out) before it sputtered and tried to start but it quit. Then it cranked another 10sec or so and the batteries died. It was about 85deg so it should have started w/o GPs.
Watching the voltmeter, GPs seemed to draw current. There's a lot of corrosion on both batteries so I know that needs to be cleaned up. Assuming the batteries aren't shot, after cleaning the corrosion, is it safe to hook jumper cables to a car to charge the batteries, but disconnect the jumper cables before starting the truck? Or should I use a plug in AC charger? I've never jumped a dual battery vehicle - not even my own 7.3.
She wants to sell it but it's in pretty rough condition - possibly normal for that age with 160K on a work truck. It was used in a business she had with her ex. The valley of death has some wet fuel in it and there is a film of diesel on the fuel bowl, fuel lines and wiring in the vicinity. I could smell the fuel before I opened the hood or tried to start it and it hadn't been run in a week. She says it runs fine and uses no oil but is always rough to start. It rolls rather than barks to life. It's bone stock with flat factory downpipe and airbox.
The engine cover is missing. Connectors and wiring on top of the valve covers appear new. She looked up the value and says it books for $7200 on KBB in its current condition. It was always parked in the sun here in Albuquerque and it shows. Body looks good as far as no rust or dents, but the white paint is faded (flat looking) and the blue interior is also pretty rough with 40/20/40 front seat and cracked dash. If I get it running I'll post it in the for sale section if she doesn't find a local buyer by then.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Cranked Fine But Would Not Fire
Owning a 2001 F250 Extended cab with a 7.3 I have not had a lot of questions to ask fortunately.
My truck has spent a lot more time sitting than running lately and when I went to start it the other day it cranked fine but would not fire. Quick read on this forum and the first thing I found was how if the fuel solenoid had less than 10.8 volts when cranking it would not start.
I went down and checked the battery voltage and it was at 12.1 volts no load. I put the battery charger on for about 10 hours (time to kill) and when I pulled the charger and cranked it over, started with no problem.
Ford 6.0L Power Stroke Diesel :: Long Start - HOP Would Fire Injectors And Start Up After Several Tries
Had long start issues. Would turn over for 5 seconds - shut off- turn over for 5 seconds - shut off - third try on 4-5 seconds the low oil pressure would come up and HOP would fire injectors and start up.
Was not sure what was up, so look it to Ford. They did leak down test and found seal at the top of injector 4 was leaking. Replaced it and leak moved to other injector. Basically moving to the next weakest seal point. I told them to stop as i did not want to pay, parts, labour and shop time to replace all injectors, etc. They also said power across all injectors was good, but 3 & 7 were not contributing on cold start.
I drove it home and bought parts. New cups and seal for all 8 on fuel rail. New gasket kits for injectors. Plus 2 new injectors to replace 3 and 7.
Replaced injectors in 3 & 7 with the 2 remanufactured i bought. Replaced all cups and seals on fuel rails. So it has new injectors in 3, 4 & 7.
As for the other injectors i took the 5 of them right apart and cleaned them and re-assembled. Took about an hour per injector, took my time to get it right, just FYI. Went pretty good i thought. Seemed pretty straight forward actually.
Now no start - no high oil pressure at all. LOP comes up right away. Scanner shows no HOP no matter how long i crank it.
FICM power good, 47.5 - 48
shows FICM sync - YES
IPR sits at 14% and jumps to 84% on crank - starting, see photos below.
Scanner prior to crank
Scan during crank
Note zero IPC - PSI
Right now.... Got the valve cover off on passenger side. Cannot see oil squirting out the sides of any injectors, but line of sight is limited. Maybe need a small mirror to see in there. LOP comes up better than it has in years, but no HOP now. Before rebuild it seemed i had good HOP but low LOP.
I drove it home from Ford and into my garage, so i do not believe the HPOP crapped out sitting in the garage, so i am ruling that out as a fail, at this time.
Dummy plugs were replaced 5 years ago and o-rings looked decent.
Pulled the small plug screw at the top of the fuel rail. Cranked it until oil came out, bleeding air. then replaced the screw plug. Have not done that on drivers sideyet. Will try that tomorrow. However, think this is more than an air issue, as i have cranked it over plenty, unless i just have that much air.
Going to pull the valve cover on the Driver's side tomorrow. Then will have both covers off at same time to view all.
Noted that if i put compressed air into the screw hole on top of the fuel rail, i can hear air coming out from below the fuel rail. Nothing at the base or around injectors. Does not seem to be at the cups either.
Just wondering.... Buy applying air to those screw plug holes, is that the same as doing the air test at the sensor that pokes up through the valve cover.
With air pressure at these scew plugs on the fuel rail, should this be sealed and be air tight and hear no air leakage. Because it was not air tight on the drivers side before i closed that side up. I am curious about this.
I am assuming i still have a HOP leak. I do not think i have a failed HPOP. How to better chase a HOP leak?
Ford 6.0L Power Stroke Diesel :: 2003 F350 - No Power On Cold Start
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - After Start Up Rough Idle And Power Lag?
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesFord 6.0L Power Stroke Diesel :: Lack Of Power / Replaced Injector Now Won't Start
I was driving and my truck started have lack of power, could barely get going on hills, tons of blue smoke (smelled like diesel) real rough idle. I unplugged injectors and found #5 made no difference. I replaced it today and I can't get it to start. It'll get to 2000+ psi 48v ficm, low pressure oil registers, ficm says its in sync. It will crank and blow a lot of black like its half firing or something. It has even crank to, until it tries to fire. From what I've been reading could it be the ficm? That one circuit is fried?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 - Hard / No Start - Low Power
Don't know where to start so I'll ramble!
2005 f350 with the 6.0. Crew Cab, 8' box, 4x4 with DRW. I use it only take the boat to the launch 5 minutes away once in a while and to pull car trailers every other week. Majority of driving is on the highway and average trip is about 300 miles. Low power and now no start.
No codes. I do have a scan Gauge and can provide data.
Was running this week, but has had a lack of power for some time. I had put 2 new injectors in last summer. Also updated dummy and stand pipes. Blue spring. Also new IPR at the time.
Ficm board was replaced in March.
New injector harness last year. New Glow plug harness last year.
Coolant level is fine and none being lost.
CAC hoses appear fine, no cracks.
No boost. But newer MAP sensor, hose not cracked or plugged and nipple on intake is clear. Put the MAP sensor last year and it didn't make a difference.
Turbo was rebuilt 2 years ago.
IPR has to hit close to 80 before boost hits 12-15. But it takes a while to get there.
Now won't start.
Yesterday am it was about 30 farenheit and no start. Last year would start no problem.
Batteries are fine. tested.
Engine fires within 3 seconds, but doesn't want to run.
ICP is above 500. climbs as I turn over.
Fires only in first few seconds and then nothing while I keep cranking it. it is cranking fast enough though.
Now...I see IPR will hit 84.7% and then 14.8%. Not good!
When running it sits in between.
FICm voltage is 48.5 key one and 47.5 when cranking.
Wondering if possibly IPR screen is plugged? Or would CKS or CPS cause issues? I recall reading about pulling one of them and cleaning rust off of it? Also...should mention, no EGR reading on scan gauge..never was either. I had checked and cleaned egr valve before. it was clean when I pulled it and not sticking.
Intake had been cleaned 2years ago. Also, on occasion, while pulling up hill, I would get power! Black smoke and it would race up a hill like it's supposed. Then it would go back to no power.
Also...if I pull the MAP hose from the intake nipple, should I feel suction from the intake? There doesn't appear to be any air coming or going from the nipple.
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Lost Power And Won't Start
I have 2005 f350 with 365000 km on it I have it for one year and don't have a problem till last week. I was pulling van on dolly uphill and sadden lost pover, so I stopped and check oil leaks ,transmission .... But everything looks ok in couple minutes start engine and go home (10 km). Change fuel filters trans filter, looked good for 50km and star losing power again and doesn't want start. So I skan and its show me next numbers.
Key on engine off
Ipr-15%
Icp-0psi
Icp-.26v
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine crank
Ipr-85%
Ficm main power-48.0
Ficm logistics-12.5
Icp- 625psi
Icp-.77v-1v
So what I have to do?
Ford 6.0L Power Stroke Diesel :: Code P2290 - Start But No Power
Long story behind it but finally got my scanner working right and checked the suggested systems for p2290.
IPR was 77+ on start up dropped to around 31 at idle
FMP is in the 46.5 to 47.5 range
SYC was at 1 and occasionally at 1.5
ICP was at 550-650 during startup and quickly ramped up to 1150 then settled into around 850 at idle.
The only thing that I'm not sure of is the IPR being 31 at idle, is that what it should be. The others I think are within normal operating parameters.
The truck starts but has no power. Can barely go up a slight hill on my street. Seems like it's going to be fine but as soon as I apply a little gas it just falls off.
Ford 6.0L Power Stroke Diesel :: Lost Power Now Won't Start - Bad Fuel?
This is a new truck to me 03 Excursion, the owner has done a lot, gave me receipts for a lot of work and cosmetically it just seems taken care of. About a year ago hpop, ficm, oem egr and 3 injectors. He wasn't happy with that mechanic and still having problems so went to a different (supposedly better) shop. This time turbo cleaned, all 8 injectors and passenger head was redone and put back on with oem bolts. Apparently it was found that a nut was dropped down valve cover by the first shop! Somewhere along the way the ICP and GP module has been replaced.
I've only driven it a couple times and seems great until last night. It was loosing power and in about 10 seconds died and wouldn't start back up. Pops but doesn't stay running. WIF dash light on and no CEL codes. Not sure where to start/what to do. I've paid for most of it and was planning to pay the rest and transfer title but I'm not comfortable doing that till I'm confident it's good to go.
I drained the separator and seemed to gush out like it should and don't think I saw water. I'm planning to take the sensor off the filter there, inspect and clean it but I don't imagine that's the problem. I do see oil coming on the back of the engine and front of tranny on the drivers side... maybe ICP is all oily and failed? I don't know much about these, just been trying to read. What should I do as some first steps? Do I need some sort of scanner? It seems like it's starving for fuel. It was about 1/4 of fuel when I bought it and filled it up the night I took it home and have put about 80 miles on it since. Is it possible it's got bad fuel or water?
Ford 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesFord 6.0L Power Stroke Diesel :: No Crank / Start - 30 Amp Fuse PCM Power Relay Is Blown
Ihave a 2008 E 350 6.0 , while driving i hit a small pothole no big deal the van stops running and coasts to the side of the road. get her towed. The dash lights show the PATS is engaged so it is no start no crank.
The 30 amp fuse PCM power relay is blown. when i replace it it blows as soon as i turn the key. im checking for wire chafing but so far have found none.
Ford 6.0L Power Stroke Diesel :: Power Loss On Takeoff And Then Stopped Now No Start Just Turns Over
So loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 Replies