Ford 6.0L Power Stroke Diesel :: Van Would Not Start Just Cranked
Came out of the building center yesterday after about ten minutes, and the van wouldn't start. Just cranked and cranked.
So I fired up Torque Pro and the HPO only got to 156.8psi. The idiot gauge came up to where it should be.
The dipstick looks good. I unhooked the ICP sensor and still no go. Reconnected.....
So I called a tow... after It cooled down.(75*F water) I tried again and got up to 295psi, but still not enough to start.
At this point I know I have recent injectors and updated Plug& pipe on the passenger side, a new IPR, and (another) new STC fitting.
I will get the air to it, and investigate, but at this point,I am leaning towards the Dummy Plug on the drivers side. Or maybe I am just hopeful because the internet says that one can remove the VC on that side fairly easily.....(Van Body)
However I did recently(2K miles/??) have the engine apart to get at the HPOP and STC leak issue I had. In the event of a possible stuck IPR- what would be the symptoms during an air test? No change with power applied? Or should I just remove and inspect?
Ford 6.0L Power Stroke Diesel :: Cranked For About 15 Seconds With No Start
This morning I went out to start my truck. It cranked for about 15 seconds with no start. I set my TorquePro to monitor the IPR% and cranked again for about 10 seconds. The IPR% was about 83.7% with no start again. I went inside and searched for "crank no start" threads to see what else I needed to look at. I went back out and added HPOP to the TorquePro. Cranked for about 5 seconds, thinking I would get no start again, but it fired up. After start I was getting about 27% on the IPR and abour 537 on the HPOP. Drove to work with no problem.
Could this just be a fluke, or do I need to be concerned about it? I have a road trip coming up to Tennessee on Thursday. I did standpipes, dummy plugs, STC fittings, EGR delete, new oil cooler and upgrade to stainless steel IPR screen about a year ago.
Ford 6.0L Power Stroke Diesel :: 2003 Excursion Just Cranked But Won't Start
My truck started and ran as it always did and about a mile it just quit. I tried to restart it and it just cranked but wont start. I bought a scangauge II and did test for the normal no start issues that Ron on you tube mentioned.
Values are as followed engine off
14.8 - IPR 0- SYC
48.0 FMP 28 - ICP - I was thinking that the ICP sensor was a newer 04 model so the values come back a little higher.
While Cranking its as follows
84.7 - IPR 1- SYC
48.0 FMP 46- ICP
Research says that I think if the IPR is bad or unplugged it could show a low value on the ICP..
Also I wanted to check both the IPR and the ICP for connection and to make sure no oil on connectors. See if the IPR screen was cracked or cut.
I have tried to find them and cant so I thought they were behind the turbo so we took that off and no i still cant find it. I have the truck apart and it got late so I have decided to take a break and come back to it tomorrow.
As I said I'm not a diesel mech but I'm pretty good with figuring things out or at least enough to get into trouble.
Ford 6.0L Power Stroke Diesel :: 2005 F550 Cranked Strong But No Start - P2285 Code
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Cranked For Few Seconds Then Dies?
My truck will only stay cranked a few seconds then dies, I have a lot of codes popping up! I was told may be the FICM.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Won't Crank Sometimes But Cranked Right Up If Use The Yellow / Blue Wire
About a month ago my 2005 Ford Excursion 6.0 wouldn't crank. Everything came on fine and there was no sign of a problem. when I tried to crank it nothing happened. I read about the yellow/blue wire on the passenger side and tried that. It cranked right up, and then worked fine with the key. No other problems until today. Same thing happened again. What could this be?
View 14 RepliesSonata NF (2006-10) :: Need To Be Cranked Several Times To Start
About a month ago, fuel pump was replaced by repair shop due to car will not start at all. Car seems to be working fine after the work done for about 3 weeks. One day of last week, car will not start immediately, it had to be cranked a couple times so it can start. It happens all the time when i leave the car off more than 5-10 minutes. If I stop the car and start right after, it starts quickly. Anyway I called the same repair shop, they told me battery may be started dying. I measured Voltage on the battery during cranking it goes down to 11V and goes back up to 12.9V after car starts. I have replaced the battery with the new one for precautionary.That did not fix the problem.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranked For About 10 / 15 Seconds Before It Sputtered And Tried To Start But Quit
A lady friend of mine got a '99 7.3 CCLB auto dually in a divorce. She doesn't drive it but starts it once a week and yesterday it wouldn't start. It cranked about 10/15sec (after waiting for WTS light to go out) before it sputtered and tried to start but it quit. Then it cranked another 10sec or so and the batteries died. It was about 85deg so it should have started w/o GPs.
Watching the voltmeter, GPs seemed to draw current. There's a lot of corrosion on both batteries so I know that needs to be cleaned up. Assuming the batteries aren't shot, after cleaning the corrosion, is it safe to hook jumper cables to a car to charge the batteries, but disconnect the jumper cables before starting the truck? Or should I use a plug in AC charger? I've never jumped a dual battery vehicle - not even my own 7.3.
She wants to sell it but it's in pretty rough condition - possibly normal for that age with 160K on a work truck. It was used in a business she had with her ex. The valley of death has some wet fuel in it and there is a film of diesel on the fuel bowl, fuel lines and wiring in the vicinity. I could smell the fuel before I opened the hood or tried to start it and it hadn't been run in a week. She says it runs fine and uses no oil but is always rough to start. It rolls rather than barks to life. It's bone stock with flat factory downpipe and airbox.
The engine cover is missing. Connectors and wiring on top of the valve covers appear new. She looked up the value and says it books for $7200 on KBB in its current condition. It was always parked in the sun here in Albuquerque and it shows. Body looks good as far as no rust or dents, but the white paint is faded (flat looking) and the blue interior is also pretty rough with 40/20/40 front seat and cracked dash. If I get it running I'll post it in the for sale section if she doesn't find a local buyer by then.
Ford 6.0L Power Stroke Diesel :: 2006 - Multiple Lights Won't Showing On Dash?
I have a 2006 F250 6.0 Powerstroke which i bought in May (My first truck and also my first diesel) that I am trying to diagnose a couple problems before it gets into the colder weather. One problem being that my glow plug/WTS light does not come on. What is the possible cause for this? My glow plugs and GPCM all work fine so if there's a bulb that would be out or where the problem would be? I'd like to have this light working before winter time for obvious reasons... and another light that doesn't work that I'd like to try and figure out is the brake light that should come on when you put on your emergency brake.
View 10 RepliesFord 6.7L Power Stroke Diesel :: Multiple Low Fuel Pressure Warnings And Hesitation At Low RPMs
So it looks like my lift pump (low pressure fuel pump and sending unit) is going. Multiple low fuel pressure warnings over last two days and hesitation at low RPMs. Not hearing pump run when I turn the key all the time but no issues starting. About 16,000 miles since last fuel filter change but picked up new filters today at dealer.
Asked about a fuel pump and he quoted PS401 and none available in Canada and had to inquire direct to Ford - 30 day wait on a part that will turn my truck into a brick if not replaced. Can't find a PS401 but I can get a PS 402 out if the USA in 5 days.
Any difference in these? Dealer is an idiot and can't even determine if there is a difference or too lazy to find out for me. I don't even know if I can prime the truck if I change filters at this point and this is a quick change job for me if I had the pump. Going over the system from back to front in the morning.
Don't ask about warranty. Just hit 160,000 KM on my truck.
Ford F-150 - 1997-2003 :: Driver Door Unlocks Multiple Times When Turn Off Key (6 - 10 Times)
2003 F150 Super Crew 5.4
When I turn off the ignition, the drivers door lock unlocks or pushes the arm through the door for up to 30-60 seconds over and over again. I would say like 10 times and it is annoying as hell.
Is the only part in the door that controls this the actuator or is there something else that can be doing this?
Ford 6.0L Power Stroke Diesel :: CEL On For Multiple Codes - Cylinder 1 / 2 / 7 And 8 Have Glow Plug Circuit Open
Just got back from the beach yesterday. On the way back I noticed the check engine light on and read the codes. It listed 4 codes, P0671,P0672, P0677 and P0678. From what I can find, Cylinder 1, 2, 7 and 8 have the glow plug circuit open. Truck ran fine and didn't miss a beat. Ambient temp was around 80 when we started up the truck so I guess diesel plugs are not to crucial for that temp. I did notice when driving back the Vbatt would jump from 12.2v at1854 RPM (34 MPH) and 13.8v at 1652 (57 MPH).
Would bad batteries or low batteries cause this type of problem? This may be wishful thinking on my part. I have tested the batts with a DMM and they are at 12.3v. I took them out and charged them but they always go down to 12.3v. FMP is 47.5v to 48.5v. It seems suspect that all four glow plugs would be bad so I assume it could be the harness. What are some ways I can test to verify where the problems come from.First thing I would do is get two new batteries as these are still under warranty.
Ford F-150 (2004-2008) :: Need To Move The Shifter All The Way Down And Up Multiple Times With The Key Open In Order To Start
I'm having trouble with my 2004 Ford F-150 5.4 Triton V8 starting, when i try to start it i have to move the shifter all the way down and up multiple times with the key open in order to start the truck. I don't what it is I think it may be the Neutral Safety Switch or Shifter cable.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Truck Will Sometimes Momentarily Cut Out And Buck A Couple Of Times
I replaced the speed sensor in the differential yesterday, but it didn't make a lick of difference. I've been having intermittent problems with the speedo ever since I bought the truck. When the speedo starts acting up, the truck will sometimes momentarily cut out and buck a couple of times. It was first mentioned this post, post # 35. I had the truck in the shop for a new oil cooler, EGR delete, standpipes, dummy plugs and STC fittings, and when I got it back it ran worse than before as detailed here in post #1. It turned out I had a torn IPR screen.
I replaced that and it cleared up all of the problems I had except for the speedo problem I originally had. The truck actually ran perfectly on the way home from work yesterday, about 20 miles. No speedo problems and no cutting out. This is not unusual, as the problem is only intermittent. I put the new VSS in last night but did not drive it until this morning. This morning, same thing again, speedo swinging crazily. When cruising about 70 it the speedo would suddenly jump up to about 90 and that is when the truck would cut out and buck a couple of time. The VSS is a Dorman product and proudly displays "MADE IN CHINA".
Should I try a better quality sensor? Rock Auto sells an Airtex/Wells sensor that seems to be of good quality, but I can't determine where it was manufactured. The only reason I bought the Dorman is because I could get it next day from Amazon. Should I be looking at another source for the problem? This is very discouraging because this one thing is what is keeping the truck from being mechanically sound, and I'm trying to get it ready to tow an RV this summer.
Ford 6.7L Power Stroke Diesel :: Transmission Clunk At Random Times From Park
It clunks real bad at random times. Whether I have had the e-brake on or not (sometimes even with it on, so I have not put any load on the locking mechanism in the tranny).
Its a 2014... Does not matter if its inclined ground or flat.
My 08 F350 V10 it replaces never once clunked.
Ford 6.7L Power Stroke Diesel :: At Random Times Engine Sounds Like It Has A Rod Knock
I have a 2016 f350 super duty with 6.7L engine, at random times engine sounds like it has a rod knock, give more fuel, it goes away, driving at 40 to 55 mph the whole vehicle shakes all at different times and different days vehicle has under 6500 miles want to now anything before going back to dealer..
View 6 RepliesFord 6.0L Power Stroke Diesel :: Tow / Haul Light Comes On Flashing At Random Times
My co-worker has an 06 F250 SC 4x4 and is getting a P0713 code. 2006 Ford F250 6.0L Diesel ... Tow/haul light comes on flashing at random times. Truck is reading a P0713 code which is the TFT Sensor Failure/Replacement
Ford dealership is telling me that I also have to pull the valve body and install the new upgraded wiring harness (3-3.5 hours labor) but a thread on this forum stated I just needed to replace the sensor in the tranny pan and reconnect the wire harness. Do I need to upgrade the wiring harness?
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Long Crank Times
So my recently purchased 2005 f350 has an abnormal long crank. I searched all the internet and everything pointed to STC fitting. Well I knew I had some other things I wanted to knock out so I ended up buying an update kit from sinister diesel. It included an updated fitting, new degas cap, updared turbo oil feed and return lines, blue spring update, and "dummy" tubes or something like that.
During the last few days I have removed the turbo, and finally got to the hpop. As I was removing the turbo I thought I might have the updated lines as there was no braided area in the feed tube. Sure enough I pulled the hpop and I have the one piece fitting. So now that I have wasted all this time removing all this stuff for no reason I still don't know what is causing my long crank. I am going to probably install the new fitting and lines anyway but where do I go from here?
Ford 6.7L Power Stroke Diesel :: Light Flashes 4 Times When Turn Exhaust Brake On
While driving into work today I noticed that when I turn the exhaust brake on the light flashes 4 times and turns back off. This definitely does not seem normal but it is cold outside. Could it being 9* have anything to do with this?
View 11 Replies