Ford 6.0L Power Stroke Diesel :: New HPOP / Low Pressure Oil Light Would Come On After Warm Up
Just replaced the hpop on my 04' 6.0. It had been down for about a year because my low pressure oil light would come on after warm up. Truck ran PERFECT, but dam light would come on. Eventually it wouldn't start by cranking, but would on a bump. (I have a 6spd.) still ran good. I would never run it over 5 minutes because i didn't want to damage anything. Finally getting around to fix it.
After a day of air testing, we tracked it down to hpop. (air coming out of turbo drain tube). I had a hunch that the dam bb on pump had spit out from similar stories on FTE, and thats what happened.
Replaced pump. (its an older style pump BTW, although i have a january 04 build and every ford parts guy said differently.) Put everything back together and now it runs terrible! We ran the truck for over 20 minutes and it didn't get better. I am afraid its gonna damage something to keep running it. My mechanic says 5 cylinders are misfiring and its something to do with the ficm or injector harness.... But, it ran perfect right before the hpop change???? Everything was double checked to make sure it wasn't something dumb.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Low HPOP Pressure
2003 f350 6.0. Ran last night and wont start today. Monitor says 85 psi pressure, should be atleast 500 to start. Could it be the IPR?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Long Crank When Cold / HPOP Is Losing Prime
6.0 has had dummy plugs and stand pipes replaced and still has a long crank when cold. The kicker is that it doesn't happen when the truck is parked nose up in the driveway. It only happens if the truck is level or back into the driveway. I suspect it's that the HPOP is losing prime from somewhere.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Crank But No Start - Low Pressure?
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
Ford 6.0L Power Stroke Diesel :: 2003 - Weak HPOP / High Pressure Oil Leak?
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 RepliesFord 6.0L Power Stroke Diesel :: Long Crank Start And No Oil Pressure When Warm - Codes P2290 And P2291
As the title says I am suddenly having a long crank when starting and low oil pressure when when warm (above approximately 100 degrees). IPR goes to 85% when cranking. Stored codes were P2290 and P2291. Other symptoms are low power and what sounds like a power steering pump with low oil whine and low power. (It is not power steering related however, I checked.) I pulled the oil filter and cranked engine and filter bowl filled in less than 10 seconds.
Oil did have a fair bit of air bubbles. Oil has 5000 miles and is Motorcraft 10w30 diesel. I have not added any since the last change. I do not have the new style pump so it's not the STC fitting. What my issue is? I do have AE if any other info is required. Particulars are in sig. The searches I have done combined with the mileage I have lead me to either the low pressure pump is failing, or the high pressure pump has lost the ball bearing out of the side.
Ford 6.0L Power Stroke Diesel :: 2005 F250 - New HPOP And No Start
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....
Ford 6.0L Power Stroke Diesel :: 2005 - No Start - HPOP Reservoir Dry?
I've gone through every possible step in diagnosing myself but can't seem to figure it out. I do not have access to shop air to do an air test. Vehicle history that I know of: Has updated STC fitting, looks to be a reman hpop. I have tested the LPOP with the oil filter housing, fills quite fast, although no pressure registers while cranking on the gauge. When I opened the HPOP case to take a look, I found the reservoir dry. What can cause the LPOP to not feed the HPOP? I will be updating everything. The truck has relatively low KMs sitting at only 163,000.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - After Replacing Seals In HPOP Now No Start
I have a 2005 ford Excursion 6.0 with an EGR delete, bulletproofed beauty. I bought it about 8months ago and It ran great. I soon bought a 270amp DCpower alternator for it after the batteries died and then replaced the batteries. I eventually developed a no start when hot issue and decided to tear into it my self with everything I've learned on FTE! I love this site and most of you are like legends to me.... so I thought, how hard could this be?
So I bought that fancy icp pressure adapter for testing the pressure from the passenger side valve cover then found one that test pressure at the IPR port. So I went and bought that too 6 0L Powerstroke Specialist's Tool Kit Air Test Tool Ball Tube IPR Sockets | eBay and it lead me to multiple leaks on both sides of the oil rail.
I also bought the CTS2 insight and started monitoring things and realized I had more problems than I thought. I'm still learning how/what to look for and monitor. Anyhow, My EOT and ECT would sometimes be 30-40 Deg. apart. So knew I'd have to replace the oil cooler.
So here I am, I bought ALL ford OEM parts which were -- Oil cooler/standpipes/dummy plugs/ STC update/updated oil drain tubes/Coolant filter/bluespring kit/bango bolts/new degas bottle cap.
I put EVERYTHING in and was careful as can be. I located my leaks and it turned out to be the injector seals on #1 #2 and #5 injectors. The one on the top of the inside of the injectors. So then I bought all new ALIANT injector seal kits (all 8) might as well do them all while I'm in there. And put it back together. Still friggin leaked at injector 1 and 2. So I polished all the nipple cups and bought 8 new ALIANT seals for cups on the rail...STILL LEAKED (swear word).
After putting everything back together and taking it apart 6-7 times...I tried sticking the air directly into the injectors (#1,#2) using a rubber nipple and the injector spill ports were pissing out air. The rest of the injectors ports didn't leak at all except for #3 which was barely a leak.
So after some reading about this problem, I read that this "spill port" leak was normal and could be that the spools were probably closed so it was nothing to worry about. Or that's what I understood.
I put everything back together one more time and got ready for some "long cranking". I should mention I filled the oil valley from the filter housing (about a half a gallon) and cranked for 20sec...Waited 2 mins...cranked 20 sec...waited 2 mins.......continuously untill batteries went dead...then I recharged them and repeated...and recharged them and repeated...I knew It would take a long time but holy cow.
I used the CTS2 to watch my icp volts and it was 0.2 KOEO and while cranking. It didnt change. So I unplugged it. Now I have 1400psi. I tried using my other F350 ICP sensor and same thing. So Its not the sensor. Maybe the harness? So I unplugged the fcim and replugged it back in. Still wont start. I'm at my wits end with this and my wife is hating me for "trying to save money" and blocking the driveway for the last 9 days...
Ford 6.0L Power Stroke Diesel :: Truck Does Not Even Crank And It Has No Fuel Pressure
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Oil Pressure Only Going To 350 PSI / Crank Longer When Cold
I have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
Ford 7.3L Power Stroke (1999-2003) :: HPOP - Low On Pressure When Even On 50hp Setting
What's better good options on a upgraded HPOP? As of now I have a stocker, it's getting low on pressure when even on my 50hp setting.... Was looking at T500 and Adrenaline. Any others could recommend? I'll be doing injectors down the road here too.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Hot Crank No Start Sometimes
The truck was running fine then I shut it off one day and it wouldn't start back up long powerful cranks but wouldn't start pulled the valve covers checked branch tubes and dummy plugs all looked good (not for sure though) replaced the icp and even tried unplugging it after the hot crank no start to see if that worked because that was the only a code I threw but alas it did not work.
I did a air test and closed the IPR valve via fancy tool and was getting some minor gurgling out of the oil filter resivuar and was guided to change the hpop being that was the beloved issue I couldn't get the j-tube out to inspect but everything else was clean as a whistle ... I was getting some air flow threw the oil filler cap and the air intake box on the driver's side valve cover but was told that is normal but not sure how normal when I replaced hpop it appears it stopped gurgling as much.
When I did the following air test but it started when cold but then it struggled but it did start then my batteries died out turns out I do have a bad negative connection I getting the batteries re charged gonna pick them up today and tighten that connection along with a new air filter via reading in the hanes manual that can sometimes cause a hot crank no start .
Ford 6.0L Power Stroke Diesel :: SCT On HPOP Can Be Upgraded?
Quick question, does an early 04 have an SCT on the HPOP that can be upgraded?
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
I have a 2004 6liter. I parked one day two weeks ago and a went out last week to move it and I will only crank over. No fire No start!!!! Have new batteries. New fuel filter and have fuel coming in to the fuel bowl. I have gone over the harness, checked my fuses. I do not have a reader or scanner. Any recommendations. I want more than just a code scanner.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Crank But Won't Start
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?
Ford 6.0L Power Stroke Diesel :: 2004 - Crank But Won't Start?
ok, so after all the work done (headgaskets, head bolts, egr valve, ipr valve, egr cooler, oil cooler, blue spring kit, new ficm injector harness connectors), this is what I'm left with on start up. I am now getting no SYNC -0
I had ficm sync before i changed the connectors on the injector harness (last thing i did besides blue spring kit). Has this motor turn this way? And my glow plug light now comes on during and post crank along with a weird fuel light with 3 teardrops I've never seen before. I need to check this out.
48.0 ficm KOEO, 48.3 crank
IPC 3 KOEO, 1100 crank
IPR 14.1 KOEO, 46 crank
IPC volt .23 KOEO, 1.23 crank
Passed bubble test
Ford 6.0L Power Stroke Diesel :: Crank / No Start - Bad FICM
2003 6.0, all stock. Crank, no start with an occasional sputter when it actually shows FICM SYNC = YES.
It had the following relevant DTCs when I scanned it:
P0261, P0270, P0276 and P0279 - Cylinders 1, 4, 6 and 7 - Injector circuit low
P132B - Turbocharger/Supercharger boost control A performance
P2614 - CMP Open circuit
P2617 - CKP Open circuit
CMP/CKP SYNC transitions to and maintains YES while cranking, however FICM SYNC transitions back and forth between YES and NO while cranking. When it transitions to YES, a cylinder or two will fire when FIPW comes up, but FICM SYNC almost immediately transitions back to NO.
Based solely on the scan tool results, Cranking shows IPR DC at about 50%, ICP PSI ~1500, ICP V ~2.0. These are stable and steady. FICM main power is at 49.5v and drops to 49.0 when it fires the occasional injector while cranking. RPM reads above 150 while cranking.
I'm thinking that since CMP/CKP SYNC stays YES and is stable and RPM reading is consistent, the CMP & CKP sensors and circuits are most likely good. I'm thinking with the codes for injectors 1, 4, 6 and 7 it probably points more toward a FICM issue.
Another thing that may or may not be relevant is the pre-cycle clatter sounds off to me. With an ambient temp of about 70F, the pre-cycle seems to repeat 3 times. The second and third cycles sound worse than the first. This is in the video below.
I work on far more 7.3s than I do 6.0s, so I'm looking for anything I may have overlooked, a second/third/fourth opinion, or if there's a flaw in my logic for someone to point it out.
6.0 No Start - YouTube
Ford 6.0L Power Stroke Diesel :: 2005 - Crank But Won't Start?
Brother in law company 6.0 died on him in his driveway after a night of plowing
It stalled out, his boss sent out a "tech" and he said it doesn't have "nearly enough" oil pressure
Now I want to further diagnose the truck myself with my scan gauge II but haven't used it for that......yet......
What should I check for IPR pressure psi or %?
I know I can get ICP pressure in PSI on my SCT x4 not sure about the Scan Gauge......
I assume a blown IPR or failed STC fitting......
Truck is a 2005..... I can figure out the scan gauge I just need to know what to look for for an idea of a blown IPR or STC or ICP.