Ford 6.0L Power Stroke Diesel :: No Oil Pressure At Idle
Trucks been running great...did an oil change today ended up replacing the oil filter return tube new oem cap and filter..now i have no oil pressure at idle no funny noises everything seems normal..give it a little pedal and the pressure jumps up to normal...
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2008 E350 - No Oil Pressure At Hot Idle
I just added 2 used 08 E350s to the fleet both about 180k on em and 1 has a little issue with oil temp and pressure. Driving ect is 222 and oil temp hits 240 then oil gauge drops to 0 and oil light comes on. I know the cooler is junk, but I am gonna pull the lp pump off and see what I find. I have a chance to fix this, or should I just order the 13k box with a reman in it.
View 13 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle And No Fuel Pressure
I head out to work this morning and truck drive fine. I do not get on it. I cruised on the highway for 12 miles at 70 mph. I get to a traffic light and then it begins to idle rough and my fuel pressure gauge reads 0. I replace both filters over a month ago and did the blue spring upgrade at the same time. I've put over 2000 miles on the truck since then without issues until this morning. Also the fuel pump was replaced by the dealer a year ago in July. No check engine codes. Where do I start looking?
View 13 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure Dropping Above Idle / Stalls Out As Soon As Try To Accelerate
Ok here is the back story over the last couple months with this late build 04 6.0 with 230,xxx miles. I had problems with it losing oil pressure at idle, which lead me to replace the hpop. After that repair the truck still wouldn't run right so i had it taken to my local shop for some diagnostics. They fixed a few electrical issues and got it running, also telling my I had 2 injectors on the way out. Due to expenses I replaced only the 2 injectors in my driveway. A few days later the ipr screen got plugged and failed. Replaced that, and changed the oil, and it ran for a week.
Now for this weeks problems. Yesterday the truck lost all power and stalled out on my wife. She pulled the codes while I was at work and this is what was listed
P0404-60===
Code: P0404 - EGR valve position control performance or range fault
P0405-60===
Code: P0405 - EGR Sensor A Circuit Low
P1335-60===
Code: P1335 - EGR Position Sensor Minimum Stop Performance
P2290-60===
Code: P2290 - ICP Too Low
Using forscan she forced the IPR 80% open and the truck would start but as soon as you try to accelerate it stalls out. Today i got the truck to start the same way. While idling the IPR was at 44% and I had about 870 psi at the icp. As soon as i would throttle up the icp would drop to around 400.
The hpop i put in a couple months ago is covered under a 1 year warranty and that's what I am leaning towards because of the plugged ipr last week. I waned to see what the great minds hear thought as well.
Ford 6.0L Power Stroke Diesel :: 2003 - ICP Pressure Low And FICM Not Syncing
I have a no start on my 2003 6.0. What I've discover is that I have two issues, ICP pressure is low and the FICM is not syncing. My plan of attack is to fix the sync problem first then the ICP issue. FICM main power is good holds at 47.32 during crank but it has no FICM sync, I've check the camshaft position and crankshaft position sync status and it returns a value of in sync, it also reaches a max rpm of 257 during crank. Given those two values I think the cam and crank sensors are good. I did a visual inspection on the wire harness and can find no chaffing, shorts or hard bends. I think I either have a bad PCM or FICM. How I can narrow it down to one of the two?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - When Cranking Low Oil Pressure Comes Up On The Gauge
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Not Enough Pressure To Start
I have a 2003 F-250. For 8 months now we have been trying to get my truck to start. We have replaced the High pressure oil pump, Oil cooler, PCM, Main wiring harness, FICM, Injectors,, ICP, and IPR. Still we are not getting enough pressure to start the truck. What is happening is the pressure will get to about 340 and will not increase from there. If we are to disconnect of one the connectors from the FICM the pressure will reach 640. Now we are able to get the truck started with ether, but will not remain started. As of right now we are still trying to figure out what is causing this problem?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Low HPOP Pressure
2003 f350 6.0. Ran last night and wont start today. Monitor says 85 psi pressure, should be atleast 500 to start. Could it be the IPR?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Fuel Pressure Fluctuates?
2003 f250 6.0 had a no start issue at first which ended up being bad connection/ chaffed wire at ficm.. ive replaced regulator with blue spring, new oil/fuel filter housing, new Motorcraft filters, and a orileys fuel pump.... guage i have reads 55psi at start up. While accelerating it obviously drops down, but it seems to goto 40 to 45psi then back to 50..then at times it goes back down while driving and stays around 40 45psi regardless if accelerating or coasting etc. Then after couple mins when i accelerate it will go back up?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 0 Oil Pressure At Idle And Metal Shavings On Drain Plug
Here is what's going on. A few days ago I noticed my oil pressure gauge drop and come back up as I was shifting from reverse to drive. Then a few days later on my way home from work I noticed that when the truck was warmed up and I was stopped at idle the oil pressure gauge would drop to zero and the oil pressure light would come on.. Once I gave it throttle the pressure gauge would go back to normal. After researching for the night the next morning I started the truck cold (around 35 degrees) and watched the oil pressure gauge. It was fine until the temperature came up then once I hit the brake to stop the high idle the gauge dropped to 0 and the oil pressure light came on. If I gave it any throttle the oil pressure would come up to normal but soon as I let off the pressure would drop off again.
I drained the oil, removed the oil cooler, and checked the oil pressure regulator to find it in normal operating condition. My new orings and gaskets won't be here until Monday so I cleaned up for the day. When picking up the oil drain plug I noticed quite a bit of metal shavings on it. I cut open the oil filter and found more shavings in it. Not a bunch but a few in every opening. I have read about a lot of issues where piston cooling jets fall off and cause my issues. I tried hitting the oil pan with a dead blow hammer and listening for the jet but don't hear it. This is the first time I have changed the oil since buying the truck and am wondering if it was found the last time the oil was changed and the reason for them selling the truck. I'm going to put a bore scope through the oil drain plug today and look for the piston cooling jets or anything not normal. Then when the oil cooler gaskets get here I plan to install them and a mechanical oil pressure gauge. To see what the pressure really is.
Ford 6.0L Power Stroke Diesel :: 2003 - Weak HPOP / High Pressure Oil Leak?
My 03' 6.0l hpop only makes about 1700 psi at wot, at hot idle the ipr is 25.1 and the icp is about 580. It runs pretty good but it seems the crank time to start is getting a little longer sometimes, other times it fires right up. It makes no difference if its hot or cold. Do pumps get weak or do you think I have a leak?....
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Reconnect High Pressure Oil Line To Rail?
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Surge At Idle After Driving For A While
My 2003 6.0 has started to surge at idle after driving for awhile. Like when I drive to work (30 min) and pull off the interstate the idle will bounce around at the stop sign (only jumping like ~100rpm). Does this sound like the ICP to you? I've replaced it once before and am wondering if it's time to do it again?
Also the truck will sometime be hard to start. And when I say hard to start I mean turn the key, let the GP cycle the turn to start and it just cranks. But as soon as I turn the key back off and cycle the plugs again it'll fire right up. It doesn't seem to matter if it's hot or cold. It's been doing it since I got the truck. It seemed to get better after the 1st ICP but didn't completely get fixed.
Ford 6.7L Power Stroke Diesel :: Low Tire Pressure Light On - TMS Pressure Low?
I had new nitto snows put on my truck and low tire pressure light is on.....Checked tire pressure 65 front and 80 back.....Started truck and screen said tms pressure low.....Hit ok and drove around on and off for 2 days now and cant get the light to go out......Is there some way to get the light out or do I have to go to my dealer to have it reset???
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Pressure Gauge Showing No Pressure
Last week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
Ford 6.7L Power Stroke Diesel :: Low Fuel Pressure And Reduced Pressure Limp Mode
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - High Idle And Stuck On Third Gear
Was driving my truck normal, got to a stop and the truck staring to idle high and like stuck on third gear and also the tow light (over drive) started to flashing Is like the truck put it self on safe mod. Drove it back home but couldn't do more than 55 miles n hour so I didn't hurt the trans.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Turbo Whistling Very Loud At Idle / High RPMs?
So I just purchased my first diesel a couple weeks ago (2003 f250 Lariat). I love it! However, I'm having concerns about my turbo whistle on it. At idle and while in higher RPMs is sounds ridiculously loud (even at 0 PSI in the boost). I've been doing my research on it and I know the 03's have the loudest sounding turbos because they have less vanes than the later models. I know without a video it's going to be hard to diagnose, but I am wondering if a loose boot would cause a turbo whining sound through the exhaust? I have yet to hear ANY other diesel in person that has a turbo whine as loud as mine.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Engine Not Running Smooth / Skipping At Idle
2003 F350 6.0 with 290k+ ... It has a skip in the engine at idle and running. At times when running down the road skip seems to get worse. Changed both fuel filters, didn't work. Truck start up is normal, no leaks, and flashing no codes.
View 3 Replies