Ford Ranger / B-Series :: Change Shifting Points - Shift Into 5th At 45 - 50 Instead Of 55?
I have a 2002 3.0 with the 5R44E. I don't like how late it shifts into 5th gear. Is there a way to make it shift into 5th at 45-50 instead of 55? I feel like I have to let off the gas half of the time to make it shift and I don't have a heavy foot. If anything, driving with a light foot seems to make it shift into 5th later.
View 8 RepliesFord :: 1967 Ranchero Stalls When Gas Is Given
My 289 has had the following done: Rebuilt and cleaned the Carb, inside and out. Dropped the tank, acid bath cleaned and sealed Cleaned and restored the sending unit All new gas line filters (twice) for a total of 4 new filters, the gas is pristine by the time it get to carb. new points, new condenser, new plugs, new rotor... all gaped correctly (checked twice) new oil, new filter. Brand new fuel pump. Checked and Tightened and Re-Tightened all the bolts, plugs wire, bolts nuts.
The car will sit there and Idle if I don't touch anything, but stalls when I give it gas. I have also tried to check for vacuum leaks using both the carb cleaner way AND the propane method. Now I will say that both sides of my exhaust manifold pipes are falling off, slightly so it is hard to hear for vacuum leaks. Would that cause a car to stall? or Am I missing a very simple step?
67' Ford Ranchero (289 V8)
Ford - Mustang :: 1967 - Overheating Only While Driving
This car has me stumped I've got a 67 mustang that is overheating only while driving I've replaced the radiator new 180 thermostat facing the proper way bypassed the heater core replaced the head gasket flushed the cooling system but after running vehicle for ten to fifteen minutes one side of the block is reading 178 degrees the other side is reading 240 in lost.
View 19 RepliesFord - Mustang :: 1967 - Car Repeatedly Won't Start
I have a 1967 Ford Mustang. I drive in mainly on the weekends. The carb is rebuilt within the last six months. I installed a new alternator about a month ago. The battery was leaking and so the car stopped running one day. I just put in a brand new battery. It still won't start. It feels like it's trying to start but just won't turn over. I did clean the terminals and lubricated them as well when I installed the new battery.
View 1 RepliesFord - Econoline :: 1967 - Getting Grinding Noise From The Rear End Of The Car
I have a 67 Econoline supervan, and have been getting a grinding noise out of the rear end at certain rpm's. It's only under heavy load, when I'm first accelerating, that the noise comes out. Now here's the question, is this the wheel bearings, or my rear differential in dire need of attention? Now, the only thing I've done so far to remedy it is change the differential oil, to no avail.
View 10 RepliesFord F-150 (2004-2008) :: Tie Rod End Torque Specs?
Just doing the bro in law's tie rod ends and we are wondering what torque we should be putting on the castle nuts? They are greasable Moogs...
View 2 RepliesFord Wiring/Electrical :: 1967 - Installation Of External Electric Fuel Pump?
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
Ford F-150 - 1997-2003 :: Grease Points On Truck?
What are the parts of the truck that should be greased? I'm about to do a front, transfer and rear differential fluid change..
View 2 RepliesFord - Explorer :: 1996 - Shift Points In RPM Or Speed
I'm not familiar with my ford truck as yet. What are the happy shift points in rpm or speed? The old VW transporter manual actually listed it. The VW wanted to shift around 2500rpm. The Explorer Looks like
10mph into 2nd
20 mph into 3rd
35 mph into 4th
Its running 3000 rpm at 75mph in 4th
Have not figured out where to go to OD. Seems to have more ooomph at lower rpm than most cars I've had. Why isn't there a red line or light on the tach? What is the higher safe rpms you can use for hills for example? Am I close?
Ford F-150 - 1997-2003 :: 1999 - Driveshaft Bolt Torque Specs
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Torque Specs For Tie Rods?
What are the torque specs for tie rods for a 4x4.
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Front Hub Assembly Torque Specs?
Tell me the torque specs for the various attaching nuts of the front hub assembly for the 99 F150 4x4 5.4L (large nut on the spindle, mounting bolts to back of spindle, etc if any) ? I will need them to put everything back together after checking the tone ring for my ABS problem.
View 1 RepliesFord Transmission :: 1967 F250 - Clanging Noise And Popping Feel When Clutch Engages
I recently changed the clutch in my 1967 F 250, all was golden. This was about 5 months ago , just the other day when going from 2nd to 3rd gear there is a clang and popping feel. the truck was making similar noises before the clutch blew out causing me to change it last time.
View 1 RepliesFord Super Duty (1999-2016) :: 2003 - Sway Bar Bushings Specs?
What are the specs for the sway bar bushings that go in the retaining bracket for a 2003 ford f250? went to advanced auto last night to get some got mine off my truck and the one they gave me was a little too small for my sway bar and the retaining bracket.
View 2 RepliesFord Super Duty (1999-2016) :: 2012 F350 6.7l - EGR System Torque Specs
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 RepliesFord 6.7L Power Stroke Diesel :: Torque Specs For Front And Back Rancho 9000XL?
What are the torque specs for front and back rancho 9000xl? Really want to know the front top spec with the rubber bushings that squish flat the most.The rest ill make tight.
View 14 RepliesFord F-150 (2009-2014) :: 2012 - Mounting New Shocks - Torque Specs For Upper And Lower Bolts?
Mounting the shock with the boot up or down? I know it doesn't matter according to Bilstein but one way has to be better than the other.
Second. What are the torque specs for the upper and lower bolts? I know the lower front is around 350lbs but haven't found anything for the rest. found out the rear bolts are torqued to 66lb.
Third. The front shocks didn't come with a boot to protect the shaft. Is one needed when the shock is installed?
Truck is a 2012 F150 FX4.
Ford Super Duty (1999-2016) :: Vacuum Gauge Connection Points?
2002 F-250 SD XLT V10
While rummaging in my garage a couple of days ago I stumbled upon a vintage Stewart Warner mechanical vacuum gauge. I would like to install it on my truck.
My question is: Where is a a good connection point for the vacuum line? Detailed direction/photo preferred as I am both Ford and V10 engine challenged.
Same question with respect to following gauges:
Volt
Oil Press
Water Temp....
Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.