Ford Super Duty (1999-2016) :: Greaseable Sway Bar Bushings And End Links
I have a 2002 F350 4x4 CC 7.3 i am wanting to change the sway bar bushings front and rear to poly and I want greasable bushings to avoid the squeaking that you get with these bushings alot of the time. I would like to change the end links to poly too i realize these wont be greaseable. What was the outcome and where did you buy the bushings. What is the size of the front and rear sway bars and the length of the end links??
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Thumping Noise That Generally Accompanies Worn Out Sway Bar Bushings
I have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
Ford Super Duty (1999-2016) :: 2012 F350 6.7l - EGR System Torque Specs
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 RepliesFord Super Duty (1999-2016) :: 2005 - Torque Specs For Crankshaft / Cylinder Heads And Camshafts?
What are the torque specs for the crankshaft,cylinder heads and camshafts for a 2005 f550 v10 6.8?
View 2 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: Body Mount Bushings Shredded On Driver Side?
Need recommendation for replacement body mount bushing. Surprised to see the drivers side shredded. Poly replacement?
View 14 RepliesFord Super Duty (1999-2016) :: 2006 F350 - Clunk In Left Front End - Radius Arm Bushings Bad?
I drive a 2006 Ford F350 4x4 Crew Cab. I think the radius arm bushings on my truck are bad. I get a clunk going over bumps on the left side in the front end.
I'm assuming it is the bushing in the rear of the radius arm, but I haven't taken it apart yet because I want to have the parts in hand. I ordered a bushing, part number 5C3Z3B203AA. But it looks too small when I hold it up to it. What is the part numbers for the radius arm bushings?
Or am I looking at the wrong thing for the clunking in the front end? I just did the ball joints with Moog both sides top and bottom. The shock bushings look alright. I have replaced the front sway bar bushings thinking that was it. What else could it be?
Ford Super Duty (1999-2016) :: Sway Bar End Link Mounting Bracket
We all know the sway bar end link problems in the early superdutys. Several years ago I installed energy suspension bushings and thought the problems were gone. Lately it started clunking again. I tightened the bolts with a breaker bar and it worked. but now it making noise again. I purchased a set of mevotech end links. Upon installation I found the problem.
Over the years of clunking the bolt hole on the upper driver side is no longer round. It has become oval shaped. I read a couple threads on here about this problem. I can't drill them out as the mevotechs have studs not bolts. Can I get the mounting bracket that bolts to the frame. Its a triangle shaped piece that the end link stud goes through. I have tried searching for it online to no avail. Whats it called?
Ford Super Duty (1999-2016) :: 2000 - Sway Bar Link Arm Removal
Working on my 2000 Excursion, 7.3, 4x4. Replacing front sway bar link arms and sway bar bushings. I got the driver side arm and the sway bar bushings done and have run into a problem removing the passenger side link arm. When removing the top connection bolt there's not enough clearance when extracting. I've gotten it loose, but as I go to pull it off, it butts up against the bell housing with about an inch of bolt left to clear the frame.
View 1 RepliesFord Super Duty (1999-2016) :: Sway / Stabilizer Bar Links Rattling?
I'm on my second set of links. The replacement were Dorman 3 years ago. They are rattling again. Do I just replace them again? I forgot to add, the bushings were replaced this year.
View 1 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Sway Bar Bushing Replacement?
I have a friend with an 01 f250 super duty who needs to replace sway bar bushings.
View 6 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Sway When Driving On The Highway
I have a question about my 2001 Ford F250 and the scary road sway I experience on the highway.
I thought it was the garbage and nearly bald tires and the fact that the fronts were bigger than the back, (Previous Owner). I went and got new E rated 265's from Discount Tire.
It actually made the swat feel worse. I thought maybe the tire guys inflated them all to 80 PSI as the sidewalls indicated. I check today and found that they went with the recommended PSI on the door sticker. 60 Front and 80 rear. But this is for the Tire size listed on the sticker.
After the tires cooled here at home I increased the PSI to 80 all the way around. I am having trouble finding my specific problem even though there is a lot of talk in many forums about this issue.
If this does not work should I try lower PSI in the rears and leave the front at 80? Should I try a front steering stabilizer shock? I did tighten up the steering box and took the minor slop out of it, Not is just makes it respond to the sway correction quicker.
Ford Super Duty (1999-2016) :: Difference Between Rear Sway And Traction Bars?
I was going to add a rear sway bar to make the truck more stable after lifting it but then I thought when I eventually do a cummins swap, with all the torque and the tall block i have in the back ill get a lot of axle wrap so i will need traction bars. So what is the difference between them? will a rear sway bar stop axle wrap as well as body roll? Also will traction bars stop axle wrap and decrease body roll? I just don't want to get a sway bar now and then need traction bars and have to get rid of the sway bar.
View 14 RepliesFord Super Duty (1999-2016) :: Front Sway Bar And Drag Link Too Close
This is my sway bar and drag link look like with the wheel turned all the way to the right. When I took these pictures, I had put the right tire on the curb too see what it was going too look like. However. Even with all wheels on level ground. It still is running very close. When the steering is straight, I have maybe 1" to 1.5" clearance between the 2. My truck does have a readylift 2.5" level kit on it. Running like this stock or leveled? Should I look around for longer sway bar links?
View 2 RepliesFord Super Duty (1999-2016) :: Front End Had Noise / Standard Sway Bar Link Knock
2004 F-250 140k 4wd 6.0. Front end had noise, standard sway bar link knock. I disconnected the sway bar on the drivers side and drove it around. Smooth and noise free. Determined new links were needed, Installed new links and now even more noise. Disconnect them and no noise again. What am i missing? Bushings look good on the axle. Is the pressure from the sway bar putting strain on another wore part?
View 5 RepliesFord Super Duty (1999-2016) :: 2012 F350 - Hellwig Front Sway Bar Installation?
Installing the Hellwig 1 1/4 inch Front Sway Bar on their 11 and up F250 or F350 SRW Pickup?
My 2012 F350 Super Cab LWB XLT 6.7L seems to have quite a bit of sway in the front end. This is especially true moving slowly such as turning into service stations or other off angle turns. The truck only has the FORD OEM puny Rear Anti Sway Bar but the front seems to accentuate sway. The Truck has Rancho 9000XL Shocks, Timbren Enhanced Suspension System as well as Torklift Quick Release Stable Loads in the rear.
The Truck I have is not overloaded but it does carry an Eagle Cap 950 Camper pretty much full time. True the Campers now days are tall so some sway is expected. I just want to reduce the apparent front end sway and wonder if others have used the Hellwig Sway Bar in the front.
Ford Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Golf IV R32 :: Rear Sway Bar Bushings Squeak?
I'm pretty certain that my 22mm neuspeed sway bar bushings are shot. they squeak like crazy and when I looked at them to grease them up it looked like they had space, oh and they knock like crazy. Any better source or place to check locally? Would Napa carry something like this? and is Poly my only option? would a rubber bushing wear quicker?
View 3 RepliesTiguan :: Front End Clunk - Sway Bar Bushings?
My Tig has been doing a sharp clunk (single) for awhile when going a bit too fast over speed bumps. I just ignored it, as I'm not flying over bumps regularly and I had just replaced the OEM struts all around. Now when accelerating over 60 kph the car has a side to side shimmy. Also when compressing or unloading the front end suddenly, like with dips on the road, makes it clunk. Checking the various suspension components?
View 6 Replies