Ford Transmission :: 1971 F250 - Loud Whirring Noise When Clutch Engages
I own a 1971 Ford F-250 Custom with the 4 Speed Synchronized Warner T-18 transmission. When I put in the clutch, once it engages, it makes a very loud whirring noise. I'm not concerned about the noise as much as possible issues with the transmission itself.
View 1 RepliesFord Transmission :: 1996 F150 - Rattling Noise As The Clutch Engages When Taking Off In First
1996 F150 4x4 with 300/6 and M5OD mazda tranny. 145k miles on it and looking really clean, and just the truck we wanted. It used to be well cared for, but has been a bit neglected since the owner passed away.
I spent a few hours searching the forums here and didn't find anything matching my symptoms exactly so I thought I would just jump in a post, but if I missed a thread feel free to redirect me.
I've got a bit of a rattling noise as the clutch engages when taking off in first. Once the clutch is fully engaged it's quiet and it shifts well and smooth. Noise also occurs (but less so) if I don't match RPM's and ride the clutch into second or third. I don't think its engine noise from lugging or anything because it goes away as soon as the clutch is fully engaged or disengaged.
Changed the trans fluid last night and no different, Clutch fluid reservoir is full, clutch travel feels good, master cylinder looks good, (slave is hidden, but looks dry though dust cover) a little play in the white bushing that holds the clutch pedal bar in place, and the plastic pushrod that goes into the firewall, thinking about replacing this linkage.
I work on big diesels for a living so i'm not scared of getting greasy. I'm almost inclined to think someone did a clutch job without resurfacing the flywheel. Is there an improved replacement for the pedal bracket and linkage? I don't mind just doing the clutch, but I don't want to be throwing my money away.
Ford Transmission :: 1996 F150 - Pedal Goes Almost To The Floor Before Clutch Engages
1996, f150, 300, 4x4, 5 speed, 296,000 miles... My pedal goes almost to the floor before the clutch engages and about a half inch, maby less, of travel back out the clutch disengages. I think it is about time for a new clutch. My question is what is the best clutch to put in my truck?
while i have the transmission slid back to replace the clutch i am planning on replacing the slave cylinder while im in there as well. Any particular brand better than the next on that item? Are there any other items that I should think about replacing while i have the transmission slid back to do the clutch?
Ford Transmission :: 1987 F250 - Rattling Noise When In Neutral And Stops When Put The Clutch In
I just recently picked up a 87 F250 with a 6.9 and a ZF5 trans. The PO replaced the clutch, and mentioned that he replaced the clutch fork too
Since I bought the truck, I've had some nasty rattling noises. It rattles when in neutral, and stops when I put the clutch in. The noise also comes back on occasion when decelerating at highway speeds, in 2nd as soon as I stop accelerating, and at low speeds in 3rd.
What is causing this?
Chrysler - 300 :: 2005 - Transmission Feel Slammed Into Next Gear Without Any Clutch / Car Shudder
My wife and I purchased our 2005 Chrysler 300 Limited in May 2004.Our 300 has over 117,00 miles as of May 2011. It has been a rather dependable automobile.I have enjoyed it almost as much as my HD. We have performed maintenance as close to the schedule as possible.
I failed to drive the car as often as our second car is an used 2002 S430 which had been my primary auto until about two months. My niece and nephew reported to my wife that the car was not "doing something right". No one could really explain, so I had drove the vehicle myself to determine the issue. The transmission had the feel that it was being "slammed" into the next gear without any clutch. Once the car was warmed up, it appeared that when it shifted at 38-40 mph or 48-50 mph, the car shudders. It almost resembles the feeling you get when you run a car across those strips in the road.
I took the car to the dealership where I have had it serviced locally. They replaced a module which had Technical Service Bulletin from Chrysler for noted similar problems. The first module replaced did not resolve the problem. I took it back and they tried again with the end result being same as before I took the 300 into the shop, transmission appeared to shudder when shifting at the midrange gears.
The dealership as another option recommended that the transmission be replaced. I was not confident with their assessment as I had the distinct feeling they were not clear on the real issue.
I took the car to another service shop which I had more confidence in their work. I asked that they check the car for the problem with the transmission as I wanted their assessment. At this point, I had pretty much decided that I would get rid of the car, but did not want to give anybody else the troubled vehicle nor did I want to have to rush to decide on an automobile to purchase.
The second shop recommended the transmission be replaced, as well several other items be checked as there appeared to be oil leaks. The CAM plugs had been replaced as part of the service the dealer performed though the engine area had not been cleaned of the previous oil. That news was alarming, as the price estimate for a replacement engine was around 6500-7000 smackeroos, way outside of my comfort for repair on the car.
I was able to locate a used transmission with only 86k on it through a very gratuitous turn of fate. I digress, however, as the source for the used transmission was available only to licensed shops.
Two shops had referenced a transmission repair shop as one of the best in our small county. I left the car with the transmission shop for their testing, and it came back with their recommendation that the problem existed in either the coil or spark or an area related there.
I again took the car to the second shop and asked that they check the engine thoroughly for any issues with the spark plugs, wires or similarly related issues. The shop reported that the motor compression was at 190 across all six cylinder and the spark plugs and wires were new and there were no issues with the coils.
I am most happy that the engine is in excellent condition. I have planned to take the car back to the tranny shop as I reported the findings to him of the other shop. I am concerned about the transmission, though I am driving it about 60 miles round trip to work about 2-3 days each week. It still convulses at the mid-range shifting but otherwise runs pretty good after that. The car body is in very good shape as is the interior.
Ford Transmission :: 1997 F250 - Shifts Very Hard And Sometimes Feel Like It Slips Out Of Gear
My 1997 F250 Heavy duty shifts very hard and sometimes feel like it slips out of gear (i press the gas pedal to the floor and speedometer rises very slow and truck doesn't move like it should.
View 14 RepliesGolf/GTI VII :: Squeak Like Noise When Clutch Engages In 2nd And 3rd Gear
Currently driving a GTI mk7 autobahn 6MT, this is my first manual transmission i have owned.. and have a question about a squeak like noise i hear when the clutch engages in gear 2 and 3.
This does not happen all the time, however i noticed that some / most of the time when i slowly let the clutch out in gear 2 and 3, right after the clutch engages and i let it out the rest of the way, it makes a squeak kinda sound.. almost like springs contract / retracting, i can also slightly feel it in the pedal.
Question is ...is this some what normal? i have never owned a MT car, and cant remember if such a thing happened while driving friends / family MT in the past..
Toyota - Sienna :: 2006 - AC Noise When Clutch Engages
I have a 2006 Toyota Sienna with approx 64K miles. Recently, I am hearing a squealing noise when the AC clutch engages (AC is working fine and blows very cold air). When AC is off for when the clutch is not engaged - no noise at all..... I have been getting alot of different answers as to what it could be and it is very confusing.... to me - it sounds like a clutch issue and I have seen videos on how to take apart and see if it is a bearing or bad clutch. I did pull the belt and checked the pulley - it turns freely and there is no bearing movement. How I can go about getting it repaired without replacing the entire compressor and other expensive parts.
View 13 RepliesGolf VI R :: Clutch Clicking / Popping Noise
Black 4 Door '13
37xx miles
Build date 07/12
No engine mods
I have had the clicking/popping clutch noise since I was breaking in the clutch but i thought it would eventually wear off. I have went through all the transmission threads and seen that a lot of people got it fixed having their clutch pedal assembly or master cylinder replaced.
Ford A/C :: 2002 - No Cooling - Clutch Engages Then Cycles Off?
I have a 2002 Ford Explorer with AC that is not cooling. The AC clutch engages, then cycles off and repeats the process over and over. With a gauge on the low side port, the pressure rises to around 65 psi when the compressor is off, then drops in seconds down to nearly 10 psi. Does this indicate low AC pressure? I have always seen the pressure pretty much stay static at a certain pressure....haven't ever seen it fluctuate like that from low to high as the compressor kicks in and out.
View 2 RepliesFord F-150 - 1997-2003 :: No Transmission After Popping Noise
My friend has a 2000 f-150 2x2 and was following him and he said he heard something pop and then no transmission , haven't put a code reader on it yet. It's not the flex plate starer works fine fluid is a little discolored and has no bad burned smell to it.
View 1 RepliesGmc :: 1967 - Transmission Shifts Erratically And Go From 1st To 3rd?
The transmission was rebuilt approximately 8,000 miles ago. It now shifts erratically instead of smoothly when you take off from a dead stop. Sometimes it will go from 1st to 3rd. When you come to a stop, it downshifts erratically also. The fluid level is correct. The truck is a 1967 GMC pick-up with 1969 350 engine. Transmission about the same year.
View 3 RepliesFord Ranger / B-Series :: 2004 - Revs Engine When Clutch Engages?
2004 Ford Ranger revs the engine when you engage the clutch then when you place it in gear it's like the cruises on it want to drive without you touching the Accelerator?
View 4 RepliesToyota - 4runner :: 1990 - Loud Popping Noise From Clutch Area
I have a 1990 Toyota 4-Runner, manual 5-speed transmission. About a week ago, while shifting gears, I heard a loud "popping" noise from the general vicinity of the clutch. I did not feel anything different in the clutch, it returned to the appropriate position and didn't feel any more or less "loose." However, after the "pop" it seemed difficult to get the vehicle into first gear and second gear, and I really had to "push" it to get it into gear, but it would not grind or anything else. Also, when shifting into reverse, it would grind loudly and be very difficult to get into reverse gear. If I turn the vehicle off, put it in reverse and then start the car, it works fine, though it seems like it "sticks" longer in reverse and takes a bit more muscle to get it out of reverse and into first again.
Additionally, when the shifter is in first gear, but the clutch is pressed, it seems as if the clutch is not disengaging entirely, because the car wants to move forward slightly when I take my foot off the brake, almost as if I'm letting my foot off the clutch a bit with it in gear. All of this has been happening pretty regularly, but the car has still been driving fine. However, today, the poor thing wouldn't start. This vehicle (like many manual transmissions) needs to have the clutch pedal pressed in order to start the vehicle. Even when I press the clutch all the way to the floor, the car won't start (and I know it is not a starter/battery issue). Given the other problems with the clutch and shifting gears, it almost feels as if the clutch was not getting disengaged all the way even when the pedal was pressed to the floor, and now that it won't start, I'm wondering what is going on. Does this model have a linkage adjuster that needs fixing? Is it something wrong with the clutch fluid? Or do I need a new clutch entirely?
Ford F-150 (2004-2008) :: Clutch Engages And Releases About 2 Inches From The Floorboard - Adjustment?
2006 4.2L The pedal is good and the fluid is full but the clutch engages and releases about 2 inches from the floorboard. Is there possibly a rod that can be adjusted at the slave cylinder that moves the engage/release point along the pedal travel? Any thoughts before I get out the creeper?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Crank But No Start - Popping Noise Out Of The Intake?
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 RepliesFord - Econoline :: 1967 - Getting Grinding Noise From The Rear End Of The Car
I have a 67 Econoline supervan, and have been getting a grinding noise out of the rear end at certain rpm's. It's only under heavy load, when I'm first accelerating, that the noise comes out. Now here's the question, is this the wheel bearings, or my rear differential in dire need of attention? Now, the only thing I've done so far to remedy it is change the differential oil, to no avail.
View 10 RepliesFord - Ranger :: 1995 - Clutch Does Not Engage / Pedal Starts To Feel A Little Spongy
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
Ford Aerostar :: 1988 - Clutch Feel Grabby / Some Sludge Accumulation Between Trans And Engine
I've got an oddball '88 SWB with the M5OD transmission. Since I've had it (about a year now), its always required a lot of gas to get it rolling without it stalling after sitting overnight or during the day at work, especially putting it in reverse for the first time. The shifts have always been a little choppy/jerky/grabby/whatever you want to call it, too. Mostly going into first from a stop, but you can feel it other gears too, especially if you're not flooring it.
Anyway, it seems to have gotten worse and I'm getting to the point where I'm looking at a cause. One thought I had was oil contamination on the clutch discs, I know this will make a clutch feel "grabby". There is some sludge accumulation between the trans and engine, and it appears I may have a very slow leak there.
I have to change the trans fluid this weekend and am wondering if there's anything I should inspect while I'm at it -- I don't know a whole lot about the clutch system on this van and there's next to no information on it. Frankly, I don't even know if its hydraulic or cable.