Ford 7.3L Power Stroke (1999-2003) :: Water Pump Lower Elbow Bolts Torque Specs
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
Ford Super Duty (1999-2016) :: 2012 F350 6.7l - EGR System Torque Specs
Replacing EGR cooler/ EGR valve. Are there torque specs going back together with the EGR system? or is there a forum that has all the torque specs id need to complete the job.
View 4 RepliesYaris/Scion & Vitz :: Torque Value For 2009 Oil Pan Bolts?
know the torque value for a 2009 yaris oil pan bolts? In another forum somebody quoted a value of 6.6 foot pounds, that seems too small and the wrong value to me.
View 3 RepliesFord F-150 (2009-2014) :: 2012 - Substantial Opening In The Lower Center - Add Protection Shield?
On my '12 F-150 Ecoboost there is a substantial opening in the lower center of the vehicle. I know that you can purchase a small after-market grill insert for that area. Is it wise to do that, or is in fine the way it is?
View 3 RepliesFord F-150 (2004-2008) :: Tie Rod End Torque Specs?
Just doing the bro in law's tie rod ends and we are wondering what torque we should be putting on the castle nuts? They are greasable Moogs...
View 2 RepliesFord F-150 (2009-2014) :: Fog Light Mounting Bars
I'm going to transfer the large Lightforce 170's that are currently on my F-350 to the new truck when it arrives. I think it's because the EB 3.5 engine has different grill/bumper configuration then other 2014 F-150's that I'm having a hard time finding a simple bolt-on light mounting bar. What to get and where?
View 5 RepliesFord F-150 - 1997-2003 :: 1999 - Driveshaft Bolt Torque Specs
What the torque spec is for the driveshaft to rear differential flange mounting bolts on the 99 F150 4x4 supercab?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Torque Specs For Tie Rods?
What are the torque specs for tie rods for a 4x4.
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Front Hub Assembly Torque Specs?
Tell me the torque specs for the various attaching nuts of the front hub assembly for the 99 F150 4x4 5.4L (large nut on the spindle, mounting bolts to back of spindle, etc if any) ? I will need them to put everything back together after checking the tone ring for my ABS problem.
View 1 RepliesFord Ranger / B-Series :: 1998 - Torquing Upper Shock Mounting Nut
I replaced the front shock absorbers on my Ranger today and I have a question about torquing the upper mounting nut. The problem I have is that the threaded rod that is attached to the top of the shock turns when I put a socket on there and try to torque it to the proper spec. You can put a crescent wrench on the top of that threaded rod(it has flat spots) and tighten the nut some with a wrench, but the crescent wrench wants to slip and round off the top of that threaded rod. So my question is, how do you torque that upper nut without the shock spinning below?
It's a '98 2.5 ltr., 2 wheel drive with coil springs.
Ford F-150 - 1997-2003 :: 1999 - Automatic Transmission Removal / Mounting Bolts To Engine?
How does one get to the top mounting bolts to engine? Are special tools required? Is there an access plate?
View 6 RepliesFord 6.7L Power Stroke Diesel :: Torque Specs For Front And Back Rancho 9000XL?
What are the torque specs for front and back rancho 9000xl? Really want to know the front top spec with the rubber bushings that squish flat the most.The rest ill make tight.
View 14 RepliesFord F-150 - 1997-2003 :: LED Mounting Bracket Install On Upper Windshield Area?
Installing LED mounting brackets on the upper windshield area? It seems like no one has brackets for the 97-03 F150 which is surprising. I'm not really interested in the mounts that go into the roof and I'm trying to find brackets that attach along the side of the upper windshield area.
I'm looking at mounting brackets that look like this : [URL] .....
Camry :: Found Torque Specs For Oil Plug
I had found the torque specs for the oil plug, oil filter housing the oil filter housing drain plug but I am unable to locate now.
30 ft lb drain plug
25 ft lb filter housing
10 ft lb filter housing drain plug
Corolla / Matrix 2009-13 :: When Power Window Reach At Upper / Lower Stop Idle Speed Drops
Just noticed the other day when when rolling up or down the window on my 2010 corolla, when the window reaches the upper / lower stop and the switch is held down, the idle speed drops and the engine stumbles. Alternator ?
View 6 RepliesGolf IV R32 :: Specs For Bearing Caps And Order To Torque Them?
I need the torque specs for the bearing caps and the order to torque them. Can't find the pdf file for the bentley. Looking for a link to the bentley..
View 24 RepliesFord Super Duty (1999-2016) :: 2005 - Torque Specs For Crankshaft / Cylinder Heads And Camshafts?
What are the torque specs for the crankshaft,cylinder heads and camshafts for a 2005 f550 v10 6.8?
View 2 RepliesFord F-150 - 1997-2003 :: 2001 - Upper Control Arm Cam Bolts
2001 F-150 4x4 5.4L. I am going to replace the upper control arms this weekend. I noticed that there are regular bolts with no cam washer installed. I have read conflicting info on whether the cam washer set up is needed. Do I have to install these or can I just put the old bolts back in just like they are. When I replaced the uppers on my 1997 T-Bird I put in new bolts but there was no mention of a cam washer setup for it anywhere that I saw. What would be the problems if I just reinstalled the old bolts. Right now the truck drives straight as an arrow but the lower ball joint on the driver side is shot so I will be replacing it also.
View 2 RepliesFord F-150 (2009-2014) :: Upper Ball Joint Worn Out?
At about 160k I noticed that the driver side upper ball joint was worn out and had a lot of play on it , so i replaced the upper control arm including ball joint(can't just replace the stock ball joint). I bought an aftermarket one with grease nipple...
Now about 2 years and 50k later, whenever I drive through a bumpy field, it sounds like something is lose and rattling right by that front wheel ,so i took off the wheel and checked the ball joint but it still seems tight..
Although I put in too much grease and that cracked the rubber boot, just leave it or should i replace the ball joint because of that rubber boot that is ripped open?
2009 f150, XLT 4x4, 6.5 ft box ....