Santa FE SM (2001-06) :: Crankshaft Position Sensor Replacement
After heavy rain yesterday my 2005 2.7 Santa fe wouldn't start today. Had it towed to nearby dealer. The crankshaft position sensor needs to be replaced. He claims its melted to the block and oil pan needs to be dropped to remove it.
View 5 RepliesGolf IV / Jetta IV :: Crankshaft Position Sensor Is Wet With Oil?
2000 jetta vr6 manual 150k miles, i have trouble starting the engine so I thought i'd start by replacing the crankshaft sensor. I notice that its wet with oil when i pull it out, and wasn't sure if tits supposed to be dry. I may have a bad ECU in the end...
View 1 RepliesAurora :: Crankshaft Position Sensors Replacement
Replacing the crankshaft position sensors on the 95-99 aurora? very difficult?
View 14 RepliesGolf IV / Jetta IV :: Won't Start - Bad Crankshaft Position Sensor?
My car doesn't start right now and a shop diagnosed it as an ecu, but I'm starting to think that is not the case. The tach doesn't move when I try to start it and pushing the gas doesn't change it, so I'm thinking it is the crankshaft position sensor. Unfortunately, down at school, I don't have access to a jack, so I was wondering if there is any way to get to the cpa without a jack? I'd rather not have it towed to another shop.
Also, my coil pack has a huge crack in it. Could that be causing my problem? And my sai has some really frayed wires and I'd rather not replace it if I don't have to because these repairs are really adding up, but could that be causing problems too? it's not causing gas mileage issues and I live in an emissions-free county, so simply not allowing me to pass emissions isn't a problem.
Sonata I45 (YF - 2011+) :: Crankshaft Position Sensor Location?
Looking for a picture or description where this sensor is located? I assume very close to the crank pulley, but I'm hoping I will not need to remove the crank pulley to gain access to this sensor. I have a 2011 Sonata, 2.4L engine.
View 3 RepliesSilverado :: New Engine Won't Start - Crankshaft Position Sensor Is Out Of Circuit
I have a 2001 Chevy Silverado 4.3L that I recently put a new engine in. The new engine will turn over but will not start. I am not getting any spark for some reason. The OBD2 code that keeps coming up says that the crankshaft position sensor is out of circuit. I have put in a new CKP sensor and new electrical connector, new spark plugs and wires, new distributor rotor and new ignition coil and still get the same OBD2 code and it won't start.
View 2 RepliesSanta FE SM (2001-06) :: Crankshaft Position Sensor Broken In Block
2002 My friend's 2.7L sante fe crankshaft position sensor went bad and I went to replace it. Removed bolt, it was stuck fast, tried to pry out and it broke off leaving the last 1/2 inch stuck in block. Tried drilling a hole in it and using a screw to get it out but no luck. Afraid to keep drilling that I might damage something behind it. How to get it out?
View 9 RepliesNissan - Sentra :: Code P0335 For Crankshaft Position Sensor
I got a 2004 Nissan Sentra and a p0335 (Crankshaft Position Sensor) popped up on it after the car stalled out sitting in a parked position for 2 mins. The car also stalled out again 20 mins later while I was driving. When the car stalled out in park I had to wait 3 mins because it was just cranking over, when it stalled while driving it started 30 secs later with 1st turn of the key. This car has been having start up issues after the car been driven and sat for 40 mins but when the key is cycled 3 times it starts up fine. I also was going to eventually make a post of this, the car been making clicking or rattling noise at times, off and on mainly when the car been warmed up and at idle more noticeably heard , hear the noise better from inside the car, forgot what side of the engine where the noise is coming from. Also I did a search in the past about recalls on this car and there was a recall on the CRANK ANGLE SENSOR on the 2.5L engines, the car I have is a 1.8L. Stated on this link 3rd one down. [URL] ... . Does it sound like the Crankshaft Position Sensor needs to get replaced?
View 19 RepliesJeep - Compass :: 2007 - Crankshaft Position Sensor Location
My son has a 2007 jeep compass 2.4l engine. He needs to change the crankshaft position sensor. Where to find it? He got a pic from autozone but you can't tell where it is on the engine.
View 7 RepliesSanta FE SM (2001-06) :: CEL Codes For Crankshaft Position Sensor - Random Misfires
I am having a problem with my 2003 Santa Fe I have taken it to have the check engine light codes read and I have a code for the crankshaft position sensor, random misfires, something with gear 2 and 3 (not sure what it was exactly) it makes a loud noise when in 1st and 2nd gear when I shift out of 2nd the noise gets less and less until its gone and then does not come back until the car sits for a little while and cools down. Its running rough and does not have any power when accelerating. I had the timing belt changed a few weeks ago and it started running funny shortly after. I don't think the guy that did the timing belt knew what he was doing because I had to have someone go behind him and tighten the pulley.
View 3 RepliesNissan - Altima :: MIL Came On / Code P0335 Crankshaft Position Sensor Circuit
My wife's 2003 Altima has been stalling. The MIL came on P0335 Crankshaft Position Sensor Circuit. I did a little research and it seems that it is pretty common for that sensor to go bad, so I bought a new one. The problem is I can't get the wires off the old one. It is in such a ridiculous place. There is no line of sight anywhere. It has to be done completely by feel. Supposedly, I should be able to push the button until it clicks and then remove the connector. When I push the button, it definitely clicks - but it doesn't stay clicked. It clicks right back out before I can pull on the connector. How can I keep that button clicked in when I can't see anything and I can just barely get one hand down in there?
View 19 RepliesCivic - Honda :: 2001 - PO335 Crankshaft Position Sensor A Circuit Error Code
33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
Civic - Honda :: 2001 - PO335 Crankshaft Position Sensor A Circuit Error Code
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
Caravan/Voyager :: 2000 3.3L Won't Start After Transmission Replacement
I just replaced the transmission in my 2000 3.3L Grand Voyager and now it won't start. It started fine when I drove it into the shop. The battery is good, the cables are ok. The starter worked good up to this point. I checked all the connections to make sure they are tight. I replaced the transmission because reverse went out.
When I turn on the key, the shift letters (PND32) appear on the instrument panel, but the little circle that shows what gear it is in does not appear. When you turn the key to the run position, the circle should be around the P to show it is in park.
When I turn the key to start, nothing happens. No clicks or anything. The next thing I am going to do is see if there is power to the starter when the key is in the start position. Where to start looking?
Caravan/Voyager :: 2006 - Engine Light Is On After Water Pump Replacement
I had to replace the water pump on my dodge Grand Caravan, which was challenging, but I got it done. But now the engine light is on.... why would that happen? I did take off the filter hose, and unplugged the cord to move the air filter housing, but I plugged it back in when i re-hooked everything up. So now I am nervous that i did something wrong. Why the engine light would come on and stay on? water pump works, put coolant in etc.... no leaks.... so now i just need to figure out the engine light.
View 9 RepliesCaravan/Voyager :: 2005 Town Country - P0032 Oxygen Sensor Heater Circuit High Voltage
P0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
Caravan/Voyager :: 2002 Vibrates And Sputters At Start Up
I have changed the oil, all filters, spark plugs and wires but the problem is still there. At start up it vibrates and sputters, gets worse at take off, lessens at 55mph but if i floor the gas it stops. Takes a lot more power to reach speeds. As much as 3000 rpm to get to 45 and almost 4000 rpm to get to 55mph. How i can fix this?
View 3 RepliesCaravan/Voyager :: 2002 - No Matter The Temperature Setting AC Blow Very Hot Air
Got a 2002 Grand Voyager (as we name it in Europe), 3,3 AWD, with AC/Heating problems.
No matter the temperature setting, from 15C to 29, it will blow with same very hot air. AC working when setting the temp to LO.
Going from LO to 15 deg C, you'll hear a "clunk", as if a door closes, and the warm air will start to flow through the vents.
Tried all the calibration possibilities known to me (ON+Recirc), and it will end with no faults, but to no good effect on the problem.
What the "ON+AC" mode does? Been in that mode - but do not know what it does, or if I'm supposed to do anything.
I haven't got a clue, other than the "thump" I hear when, possibly, the blend door closes, might be a problem, since I would expect the blend to be more gradually invoked.
Caravan/Voyager :: 2002 Van Will Not Move Into Any Gear / Won't Go Forward Or Reverse
The gear shift works fine, and we lifted the hood and saw that the mech. arm IS working when we shift. However, the van will not move into any gear. won't go forward, reverse, etc... it acts like it isn't shifting.
i was driving down the highway, and noticed it wasn't accelerating and stepped on the gas.. .and nothing. I stopped the van, put in park, turned it off. Started it again, and put in D and wouldn't go, just engine revved. then put in reverse and same thing... didn't move but engine revved.