Caravan/Voyager :: 2003 - No Reverse After Starting And Now Won't Move
I have a 2003 Chrysler Town and Country and my problem started with no reverse after starting car. If I pushed it back and drove forward 10 or 15 feet then reverse would work fine and shift properly. As long as I could drive forward first then reverse would work. This was like this for a few days then the vehicle wouldn't move at all. There wasn't any error codes. The fluid is full and clean.
When the van was about a year old I took it to the dealer with harsh shifting and they said there was a broken wire to the trans, I am thinking this is when they came out with the 3 wire slice people where talking about.
I wasn't needing the van so it has been sitting now for almost a year. Now I want to get it working again...
Caravan/Voyager :: 2000 - Shuddering While In Gear And Not Moving Especially In Reverse
My 2000 dodge caravan with the 3.3 is shuddering while in gear and not moving especially in reverse . As soon as you start going it stops . No slipping whatsoever. The van only has 130'000 miles on it .
View 2 RepliesCaravan/Voyager :: 2002 LX V6 - Transmission Stopped Shifting From 3rd To 4th Gear
I have a 2002 Town and Country LX with the 3.3L V6. Recently the check engine light went on and later the transmission stopped shifting from 3rd to 4th gear. All the gears work properly except for 4th. It doesn't seem like anything is wrong with the transmission, would this be a sensor problem? If so which sensor would need to be replaced?
View 14 RepliesLumina :: 1993 - While Turning Makes Grinding Clattering Noise - Won't Move Forward But Will Move In Reverse
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
Chevrolet - Blazer :: Barely Move Forward And Will Not Move In Reverse
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesCaravan/Voyager :: 1994 - Over Revving Engine To Get Van To Move
I have to over rev the engine to get the van to move. After that the tranny seems to work fine. Tranny fluid level is OK, and it does not smell burnt. After I over rev the engine to get moving, the engine revs seem to get back into sync for the speed I'm doing - usually just as the van starts moving, the over-revving is no longer there. Do I need to adjust the bands??
View 2 RepliesBmw - 330 :: Cold Car Would Require 3 - 4000 RPM To Move / Forward Or Reverse
2004 BMW 330i 140k miles.
We first noticed this problem a year or so ago. At first, it happened only on cool mornings if the car had been parked outside. The cold car would require 3-4,000 RPM to move, forward or reverse. After about one minute or 3-4 blocks, the transmission worked perfectly at the touch of the throttle for the rest of the day.
It only happens about half the time. Other times, even if cool and after being parked for days, the transmission engages normally from idle and up.
Once recently, it deviated from this pattern. After sitting overnight, it started and pulled into the garage normally. I shut it off for a couple of minutes to place ramps in front of the tires and restarted the car. It did not want to move on the second start. It took 3500 RPM to climb the ramps. That was scary. The car has never suddenly engaged, but if it had suddenly engaged at that moment, it would have shot me through the front of the garage.
Last week I took it to the transmission specialty shop with the best reviews in town. As life would have it, he kept it three days, driving it four times, and it worked perfectly each time he drove it. Fluid looks fine (replaced at 120k miles) and fluid level is perfect. No codes stored in transmission computer.
I thought it was intermittently draining the torque converter until this last time when it failed after being shut off for only a couple of minutes.
The transmission guy is not interested in rebuilding the transmission even if I wanted to try it. He worries that because he does not know what is causing the problem.
Caravan/Voyager :: 1996 SE / Turn Wipers On And Motor Growls But Wipers Do Not Move?
Turn wipers on and motor growls but wipers do not move, checked 30 amp fuse and it is good, all other functions of the multifunction switch are good.
View 2 RepliesCaravan/Voyager :: 2003 Not Shifting Into 3rd Or 4th Gear
Changed input and output sensor, replaced solenoid pack, cam and crank sensor. Runs good code on odometer 1684 p700.
View 4 RepliesMontana :: 2006 SV6 Clunking When Start To Move Forward Or Reverse
I have an 06 Montana sv6 that clunks when I start to move forward or reverse. Not when I put it in gear but as I start to move. It also does it when I take off from a stop sign. It doesn't make any noise while driving or turning though.
View 1 RepliesFord Ranger / B-Series :: 2000 - Won't Move Forward Or Reverse?
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 RepliesCaravan/Voyager :: GC Started Cutting Out While Idling In Gear
MY gc started cutting out a few weeks ago while idling in gear. I changed out the four plugs I could get the wires off. It's a v6. It started running better for a couple of days. I need to know of any way to get the stuck boot off. I also have a feeling there is something else wrong. Anything else that might be causing it to cut out. It has progressed to cutting out while going down the highway.
View 4 RepliesCaravan/Voyager :: 1995 Plymouth SE Transmission - Only Go In First Gear And Never Come Out
I have a 1995 Plymouth Voyager se about a year ago the transmission started acting up, for no reason, it would just go it to First and never come out I would stop turn it off turn it back on again and it would be fine..then days later it would go by, it would do it again. it did this for a while and the good days would turn in to a mile or two then it just decided not to come out of first ever, during this, i took it to a trany shop and rebuilt the transmission it worked for a bout a half hour.
Final a mechanic friend checked the computer again and changed it out with another and it fixed it beautifully!!! ok well about a week ago a very odd loud obnoxious squeal started that sounded like a bottle rocket but not all the time, more often than not though. Before I got a chance to take it to my mechanic friend i was driving along and the transmission slipped in to first and wont that's it. i have been doing emergency trips in first gear and also the horrid squeal is gone. the thing have to be linked what should I try and i don't think its the computer, I really don't want to lose my van
Lexus GX 2004-09 :: Brakes Lock Up After Washing - Car Will Not Move In Reverse Or Forward
After washing my 08 GX and putting in the garage to wax dry I have found that the next time I get in it to drive-often a day or so later,the car will not move in reverse ( or forward) without me revving it up quite high to overcome the locked up pads on the rotors. Sometimes its even screeches the tires to get in unlocked. I just washed it and letting it sit outside for a bit to see if the sun will dry out the rotors/pads and that would work.
View 10 RepliesSanta FE SM (2001-06) :: Transmission Go Into Reverse Just Fine But Would Not Move In Any Forward Gears
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesDodge - Transmissions - Grandcaravan :: Shifts Just Fine Going Forward But Will Not Move In Reverse
I am considering buying a 1999 Dodge Grand Caravan with a reported transmission problem. Mileage is around 120k, and the price MIGHT be reasonable even if a trans rebuild would be necessary. I have not seen the vehicle yet, so I'm not yet committed to anything.
Seller claims the car shifts just fine going forward but will not move in reverse. Is this immediately clear that rebuild is going to be necessary? Are there less invasive repairs possible such as valves or controls or other parts which might solve this problem?
I suppose a Caravan transmission at 120,000miles is probably nearing the end of its lifetime, at least that was true of older ones. But like I said, the price is low enough that the cost of a rebuild might be justifiable if all else about the vehicle looks good. I want to have a better sense of the prospects before I invest time in going to look at this...it's about 50 miles away. I have a local transmission shop that I trust and which has reasonable prices
Caravan/Voyager :: 2002 Vibrates And Sputters At Start Up
I have changed the oil, all filters, spark plugs and wires but the problem is still there. At start up it vibrates and sputters, gets worse at take off, lessens at 55mph but if i floor the gas it stops. Takes a lot more power to reach speeds. As much as 3000 rpm to get to 45 and almost 4000 rpm to get to 55mph. How i can fix this?
View 3 RepliesCaravan/Voyager :: 2002 - Crankshaft Position Sensor Replacement
I need to replace the crankshaft position sensor. On my 2002 Grand Caravan Sport 3.3liter. Where it is in laymans terms.
Is it better to approach from the underside Or from the hood side? I will know it when I see it but I haven't seen it yet!!
Caravan/Voyager :: 2002 - No Matter The Temperature Setting AC Blow Very Hot Air
Got a 2002 Grand Voyager (as we name it in Europe), 3,3 AWD, with AC/Heating problems.
No matter the temperature setting, from 15C to 29, it will blow with same very hot air. AC working when setting the temp to LO.
Going from LO to 15 deg C, you'll hear a "clunk", as if a door closes, and the warm air will start to flow through the vents.
Tried all the calibration possibilities known to me (ON+Recirc), and it will end with no faults, but to no good effect on the problem.
What the "ON+AC" mode does? Been in that mode - but do not know what it does, or if I'm supposed to do anything.
I haven't got a clue, other than the "thump" I hear when, possibly, the blend door closes, might be a problem, since I would expect the blend to be more gradually invoked.