Camry :: 2010 - Chrome Window Molding Removal?
I would like to remove the chrome window molding around the front and rear doors of my 2010 Camry. Is it difficult to remove? More importantly, when I go to reinstall it - is it difficult to get straight like OEM fit and finish?
View 3 RepliesCamry 2012+ :: XLE - Adding Body Side Molding?
I have a '15 Toyota Camry XLE V6 Blizzard Pearl
I was thinking of adding on Body Side Molding.
How does it look in person? any pictures?
I had cars with it that I've added on after. I like the look of it either way [on or off]
Camry 2012+ :: How To Replace Window Pillar Molding
Long story short, the tint shop burned my exterior door pillar when I got it tinted like 8 months ago. Just now felt like dealing with it, so I got the new part in. How to replace it? The back has a lot of what looks like double sided tape and only 1 clip. In order to get the other one off it looks like I have to take off the chrome strip at the bottom since the black molding goes underneath the chrome...
Pic of how the molding is on the car ....
Pic of the back of the new one ....
Camry :: Drive Belt Removal On 2003 Vehicle?
How to remove the drive belt on my 2003 camry 4 cyl.
View 5 RepliesTiguan :: Lower Exterior Door Plastic Molding Removal?
How to get the plastic exterior molding on the base of the doors off. I see 2 screws and thats it. Is there a trick to it? I need to replace the passenger side or epoxy one of the clips back on then remount it.
View 2 RepliesFord F-150 (2009-2014) :: Winch Mount Installation - Removal Of Plastic Molding?
Installed the Rough Country winch mount yesterday. One hour, by myself. Used a floor jack to lift it in place.
Only problem was removing the plastic molding which came in the spot the fairlead will be. Just a small rectangular plastic molding with a couple of bars down the middle for looks. It had two screws on top edge, and two pushpins on bottom , but also was molded with two catches on each side on the back I did not see. When I figured it out, and squeezed with just my fingers, little too hard and snapped one catch on each side. They slide into a slot and catch but wont be doing that ever again. Oh well.
As for mount, solid and easy to install. I used hand tools as the air gun would only hit one of the bolts for the front tow hooks. The other was blocked by plastic molding. No big deal.
Hidden Winch Mounting Plate for 09-14 Ford F-150 Pickup [1010] | Rough Country Suspension Systems.
Camry 2012+ :: Line Out Converter On A DSP Stereo?
I did a sub and amp install on a friends '14 SE with the upgraded stereo with DSP. I ran the line outs off the front channels, like I did with my standard stereo. Should I have ran the line out off the rear channels? I know that they cut off the bass signal to the rear speakers on the standard stereo, and that alters the signal going to the line out. Is the opposite true on the upgraded stereos? Do they cut the bass output on the front channels instead of the rear?
View 2 RepliesFord Ranger / B-Series :: 2000 - Window Belt Molding?
A C-note for those 2 pieces of nothing seems ridiculous. Considering sanding and painting instead.
View 2 RepliesCamry 2012+ :: Back Up Camera Don't Line Up With The Side Of Car
I just installed a back up camera - great picture clear day and night but the problem I am having is the guidelines on the camera don't line up with the side of the car, the driver side seems fine but the passenger is around a foot short, I have mounted the pavement twice so far.
View 1 RepliesCamry 2012+ :: 2.5L Engine - Capacity To The Fill Line?
We have a 2013 Camry with the 2.5l engine.
I just changed the oil and filter for the first time. The good book says the capacity is 4.6 qt. I did that, started the engine, let it circulate then shut it off for a half hour. The dip stick shows about half way between the full and add markers. So, seems like the capacity to the fill line is more like 5 qt.
Camry 2012+ :: Front Map Light Assembly Removal
How to remove the front map light assembly. I was trying to replace my map light with LED and one of the holder came off from the assembly. Is there anyway to secure it without removing assemble?
View 1 RepliesCamry 2012+ :: 2014 SE - Front Bumper Chrome Trim Removal
How to remove the chrome trim around the fog lights and the chrome bars beside them I have a 2014 SE
View 2 RepliesCamry 2012+ :: Center Console Removal - Adding Accent Lighting To Car
I have a camry se and I am currently adding accent lighting to my car. I am trying to take the area around the shifter and the cupholders out so I can hide some wires and mount the led lights controller. How to get this out?
View 4 RepliesCamry 2012+ :: Seat Belt Chime Deactivation?
Is there a way to deactivate the seat belt chime??
View 14 RepliesCamry 2012+ :: 2015 LE - Seat Belt Buckle Disappearing
I just bought a 2015 Camry LE. The back seat belt buckles keep disappearing beneath the seat surface when you try to put your seat belt on. It's even more annoying when you have a child trying to buckle up in a booster seat. I went back to the dealer & they showed me several other 2015-2016's and they all do the same thing. Apparently, it's a Toyota design flaw & not an annoying quirk to my car. Any solution to keep the buckle above the seat?
View 4 RepliesCamry :: 2004 - Leaking Gas After Pump About Line Before Full Line
I have a 04 camry and this car leaks gas after i pump about line before the full line. What do i need to do?!
View 2 RepliesCamry 2012+ :: 2015 - Disabling Seat Belt Chime Didn't Work
I'm in the habit of starting the car andthen putting on my seat belt while it is warming up.So I used the Carista OBD2 app to disable the seat belt chime on my 2015 Camry. This is supposed to be the same as doing it from Techstream, I believe.But the ding still sounds several times once I turn the key. The seat belt warning light also flashes in synch with the dings.I confirmed the settings:
Seat belt warning ding (driver)
ENABLED / *DISABLED*
Seat belt warning ding (front passenger)
ENABLED / *DISABLED*
Camry 2012+ :: Repetitive Squeaking Noise From The Front - Belt Tensioner Has Constant Wobble?
I have a 2012 Camry LE 4 cylinder non-hybrid at 31,000 miles. I was changing the oil yesterday and noticed a repetitive squeaking noise from the front passenger side of the engine. Upon looking closer, the belt tensioner has a constant wobble. Maybe around 1 cm of deflection with the belt. The AC condenser was running. Is this normal? Do I need to replace the tensioner? If so, what the torque spec is for the main tensioner bolt (pivot bolt)?
View 1 RepliesFord F-150 (2004-2008) :: Transmission Line Removal From Radiator
How do you remove the transmission lines from the radiator. I have to replace the radiator and don't want to mess up the lines.
View 1 Replies