Ford F-150 (2009-2014) :: Winch Mount Installation - Removal Of Plastic Molding?
Installed the Rough Country winch mount yesterday. One hour, by myself. Used a floor jack to lift it in place.
Only problem was removing the plastic molding which came in the spot the fairlead will be. Just a small rectangular plastic molding with a couple of bars down the middle for looks. It had two screws on top edge, and two pushpins on bottom , but also was molded with two catches on each side on the back I did not see. When I figured it out, and squeezed with just my fingers, little too hard and snapped one catch on each side. They slide into a slot and catch but wont be doing that ever again. Oh well.
As for mount, solid and easy to install. I used hand tools as the air gun would only hit one of the bolts for the front tow hooks. The other was blocked by plastic molding. No big deal.
Hidden Winch Mounting Plate for 09-14 Ford F-150 Pickup [1010] | Rough Country Suspension Systems.
Lexus GX 2004-09 :: Exterior Molding Of Passenger Door Is Unclipped
Just picked up a new to us 2004 GX470 for my wife.
One of the things wrong with the GX470 is the passenger door exterior molding is unclipped at the bottom. I ordered new clips from eBay and they just came in. Now I just need to figure out how to get the molding off without making the problem worse so I can replace all the clips.
Phaeton :: Rear Molding Lower Door Separated From Car Body
I've noticed on both rear doors, the Lower Moulding (black cover at the bottom of the door) #12 in the attached diagram (Light Blue Circle), is very much separated from the body of the car, it's like bended toward the outside, but it seems to be exactly the same on both sides, I am not sure if this is normal or mine has a defect
Both front doors are OK, not 100% perfectly aligned with the body of the car, but MUCH better than the rear doors....
Passat (B6) :: 2007 - Driver Side Door Exterior Pillar Panel Removal?
How do I remove the drivers door exterior pillar panel from a 2007 vw passat. I have a dent in the panel and want to replace it..........
View 3 RepliesGolf V R32 :: How To Remove Plastic Pieces Framing The Lower Door Sills
What is the trick to removing the plastic pieces framing the lower door sills? i dont wanna just start yanking i need to run a wire from the trunk forward.
View 2 RepliesLexus IS 2014+ :: Plastic Sounding Rattle (exterior) When Hitting Bumps
Experiencing a plastic sounding rattle (exterior) when hitting road bumps? This noise appears to emanate from around the wheels and can only be heard when the windows are rolled down. Model is 2014 250 fsport. The car sounds cheap when this happens.
View 5 RepliesLexus RX 2010-15 :: Loose Lower Side Molding?
I recently discovered that my lower side molding on my front passenger side door was loose while cleaning away some of the salt stains from the winter storm . how to fix it or do I need a replacement.
View 11 RepliesCamry 2012+ :: Belt Line Molding Removal?
I just bought a '12 Camry SE. However, the belt line molding (shiny trim piece below window) is dented in. How can I safely remove the piece without damaging anything? I may be able to knock the dent back out of this piece after removing it. Any specific tools required for removal? If I purchase the new molding from the dealer it will cost about $100, which I would like to avoid.
View 7 RepliesCamry :: 2010 - Chrome Window Molding Removal?
I would like to remove the chrome window molding around the front and rear doors of my 2010 Camry. Is it difficult to remove? More importantly, when I go to reinstall it - is it difficult to get straight like OEM fit and finish?
View 3 RepliesCamry :: 2011 - Plastic Engine Cover Removal
How do I remove the plastic engine cover from a 2011 Camry ?
View 2 RepliesCamry :: 2007 V6 - Plastic Engine Cover Removal?
I have a 2007 Camry XLE V6 that needs new spark plugs and the first thing to remove is the plastic engine cover. I do not see any screws or bolts attaching it down and I would like to know the proper way to remove it without damaging it or the plugs holding it down. How to do this?
View 3 RepliesAccent RB (2012+) :: Puddle Of Antifreeze On Lower Plastic Under Body
2012 Hyundai Accent
30,000 Miles
Replaced cap
Changed hoses and antifreeze
Leak seems isolated to the upper hose from radiator to filler neck.
Dealership did pressure test and changed clamps with no success.
Not overheating.
I noticed the smell of antifreeze one day and upon inspection came across a small puddle of antifreeze on the lower plastic under body. The car only has 30k on it and decided it wasn't the hoses. I noticed spots of antifreeze around the filler neck and thought it might be the cap. It was a cheap part so changed that out for a new one and still had puddles. I thought it might be the hoses after all and decided why not change all the hoses and antifreeze. Still the puddles are there which only leaves me to believe that it's the filler neck. Unbolted the filler neck for inspection and the inlet/outlet have no issues. I'm thinking it might be where the cap sits on the filler neck. It only seems to happen when it's under pressure. At start up there is no issues. I tried to let it heat up and build pressure to see if I can spot the leak but no joy. I'm guess it happens while under throttle.
Ford Excursion :: Removal Of Rear Plastic Piece From The Glass?
Mine is peeling like I know they all do and I want to sand it and re-paint it. How exactly does it come off?
View 8 RepliesPassat (B6) :: How To Remove Side Chrome Door Molding
How do I remove side chrome door molding? Do they clip off?
View 3 RepliesPassat (B6) :: Creaking - Plastic Dash Trim Removal On Passenger Side?
How to remove the plastic dash trim on the Passenger side? Is there a way to do this without removing the glovebox? I know there is one screw that needs to be removed. Mine creaks pretty badly. Ive already removed the center console trim and added felt to all those pieces. No more ticks/ creaks.
I guess I could have the dealer remove it but I dont want them taking my glovebox out to do it = more rattles. Why does VW make it so difficult to remove something that should be so simple!!
Golf/GTI VII :: Squeaking Exterior Door Handles?
Just noticed the other day that the door handle on my GTI squeaks when pulled, especially when done slowly. The only one that does it is the driver's side. I'm guessing it needs some kind of lubricant?
View 7 RepliesPassat (B6) :: Way To Remove Exterior Door Handles?
Looking for a DIY about removing exterior door handles? I am referring strictly on the handle, not the mechanism inside the door.
View 1 RepliesPassat (B5) :: 2001 - Door Frame Interior Molding Falling Off
I have an 01 B5 Passat and the interior cloth covering surrounding the front door frames keeps coming off the rubber gasket. I have tried many different types of glue and contact cement but nothing seems to last longer than a few months.
View 3 RepliesFord Super Duty (1999-2016) :: 2012 - Removal Of Plastic Tailgate Cap?
Looking to sell my '12 F-250 turbo diesel Lariat. She's in great condition, and only 8000 miles. Her only sore point is some scratches and scuffs on the plastic cap on the top edge of the tailgate (see picture below). I think it's part # BC3Z-9940602-B.
How to remove this cap, preferably without breaking/scratching anything else. It looks like there are no external fasteners, so I'm guessing it's just held on with clips on its underside, or some such. It might be more obvious once I get and examine the replacement part, but just figured I'd ask.