Ford Aerostar :: 1997 - Squeaking Noise When Turning - Serpentine Belt Tensioner?
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesCamry :: Engine Noise - Bad Serpentine Belt Tensioner Is Seized On
After finally identifying a bad serpentine belt tensioner for being the the culprit for my engine noises, my mechanic said that the 'thru-bolt' is siezed. Since the replacement job was at my budget limit he said he doesnt want to get into it in fear that he has to brake the bolt and drill it out (requiring 2-3x more labor cost according to him).
If this is the case, and the 'thru-bolt' is seized, is this in any way something I can make a an effort to tackle? I have a jack and jack stands, and plenty of time.
Toyota - Rav4 :: 2008 - Constant Squeaking Noise Coming From Front End
I just had new pads and rotors puton and I have a constant squeaking noise coming from the front end where the parts were put.
View 1 RepliesAccent LC (2000-05) :: Constant Squeaking Noise Coming From Front Right Side
I have a 4 door 2005 Accent with ABS. I mainly drive in the city, and lately I noticed a squeaking noise that sounds like it's coming from the front right side (from inside the car); it is a constant noise. I pulled the brakes off both sides, the pads are fine, the rotors were a little rough (normal). Before I reinstalled everything I took some 80 grit emery cloth and roughed the pads and the rotors with it just in case there was some glazing.
The noise is still there and what concerns me more than the noise is the fact that the longer I drive the car the more gas I seem to need to apply to get the car to move.... not a huge amount but enough. Also, once I stop the car, there is a slight brake smell and the passenger side front tire area (brake) is crazy hot. Long story short; I would like to check to see if I have a stuck piston in the caliper, But I'm not 100% sure how to. Do I pull the pads off, push the piston in , watch how fast it goes in, and then compare it to the drivers' side? Or do I need to pull the caliper apart?
Camry 2012+ :: 2015 - Squeaking Or Ticking Noise Coming From Front Windshield Area On Passenger Side
Having problems with a squeaking or ticking noise coming from the front windshield area on the passenger side? I took off the A-pillar and tweeter speaker cover, and the noise was still there. Pressing on the A-pillar did not work and it's not any of the cords or plastics in there rubbing. It almost sounds like it's behind the A-pillar. Pressing on the dash, windshield, headliner, etc. all have no effect on the noise.
I'm trying really hard to fix this myself because I'm worried about a tech tearing apart the dash trying to fix it. It might end up worse than it is now. I'm thinking this TSB will need to be done (which seems to apply to all Toyotas): [URL] ....
Next on my list to check is the passenger side mirror (make sure it's fastened securely) and also the black liner under the windshield wipers. I also have foam (like the kind you use when installing a window AC) which I may also try stuffing into the bottom of the front windshield (and maybe the top) to see if that works.
If all else fails, the car is going to the dealer I guess. The Camry is such a quiet car that the noise is really irritating in an otherwise quiet interior. Other than this noise, the car is great! Just a little bummed because my 2005 has zero rattles or noises and my gf's old 2009 also had no rattles or noises. The 2015 refresh is nice, though we're still on the fence about the front grille. My relative is waiting for the 2016's to be released later this year and then he will be buying one for his patrol car. The 2015 isn't a full redesign but it looks different enough that he wants to wait for the next MY to come out. He's dreading leaving behind his 5MT Civic but it needs to be replaced. He hasn't had an auto, ever, come to think of it..
It sounds exactly like this, and is at its worse when accelerating: [URL] ....
Camry :: Squeaking Noise Coming From Belt
I started hearing squeaking noise around the Serp Belt Tension-er a week ago. I hear it during idling and louder when A/C is on. I took it to my local mechanic. This guy is very good and he is a certified Lexus mechanic.
He told me that the Serp Belt is the problem. He changed it, but squeaking noise still continued. The mechanic then told me that we need to change the Serp tension-er itself. I changed that too. Still the noise didn't go. He told me to change the Tension-er Pulley. I changed too, but the noise is still there.
I have already spent around $600 and I have the same issue as it was there before. Mechanic at some point said he is not able to figure out what the issue is.
I browsed online and could see some complain that it could be water pump or alternator. I don't want spend any more money on getting a new spare part until I know that is the problem.
Ford A/C :: Pulley Play (wobble) / Awful Noise Under The Hood But Not Constant
I have been hearing on occasion (not constant) an awfull noise under the hood. Even when I turn on the ac it doesn't change the depth of sound. I took the belt off and spun the idler pulley, tensioner, and ac pulley. When I spun the ac pulley I notice quite a bit of play (wobble). last summer sometimes I needed to give the clutch a bit of persuasion in order for it to kick in. Is this play (wobble) in the pulley normal? I've never had to replace an ac clutch so I don't have any experience to go on.
View 8 RepliesCamry :: Idler Pulley Replacement On Serpentine Belt Tensioner
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesPrius (2004-09) :: Noise From Belt Tensioner Bearing?
During the 120000km (75000mi) service my Toyota local service said I have a noisy Prius and that the sound is from the belt tensioner bearing.
As I bought it used and always heard the same sound. I've made a video ....
Santa Fe (CM - 2007-12) :: Belt Tensioner Making Noise
I own a 2008 santa fe SE, the belt tensioner start to making noise recently, just wonder if it's covered under the warranty so I don't have to pay out-of-pocket to get it fixed. This car have 68000 miles so far.
View 19 RepliesCamry 2012+ :: Squeaking Noise Coming From The Sunroof Area
I've taken my Camry in several times (service and warranty issues). One of the issues was a squeaking noise coming from the sunroof area. It was driving me crazy especially with the weather changing it was a lot more noticeable. I took it in and they said they fixed the problem by adding insulation to the roof. Well, the noise was still there. I took it again today and the Master Technician came out and wanted me to show him what I was talking about.
We went for a short ride around the dealer parking lot. He heard the noise and told me to drive to the detailing area. He then proceeded to get a paper towel with some cleaner and wiped the metal opening around the sunroof area and the black seal on the sunroof. He then got another paper towel and put some sort of lubricant and voila the squeaking noise is gone! I keep my car very clean and wipe down the sunroof area every time I wash my car. He said to go ahead and put some type of protectant (Meguiars) so it keeps the rubber moist.
I thought it was something serious with my sunroof turned out to be a very simple applying of protectant to a piece of rubber.
Camry 2012+ :: Squeaking Noise When Going Over Speed Bumps Or Certain Dips
My question today has to deal with my squeaking car. Only mods I have done to my suspension would be Lowered on Progress springs and added there rear sway bar. After about a year my car started to squeak when going over speed bumps or certain dips BUT ONLY THE REAR. I have tracked the problem down to my rear sway bar. What is the fix for this? Ive read in other forums (mainly civic teggys etc) that the bushing might be worn? What is my recommended next step?
View 1 RepliesLexus RX 2004-09 :: 07 - Serpentine Belt Tensioner Pulley Making Noise
My tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesFord F-150 (2009-2014) :: 2012 - Squeaking Noise From Front Suspension Area?
I've got an '12 F-150 with 7k mi. on it. It developed a squeak/creak noise about 1k. mi. ago. It comes from the r. front suspension area and I noticed it one morning leaving from work. It occurs under suspension loading/unloading and it only happens during cold and dry conditions. It won't make the noise when it's wet or damp outside. I've had it at the local dealer 2 times now and they can't seem to locate it. It sounds like rubber on metal or when the 97 & 98's had the dry tie rod ends or ball joints problem. They are reluctant to throw parts at it to try and eliminate it and I agree with them. What were the findings?
View 5 RepliesLexus RX 2004-09 :: Chirping Noise Coming From Belt Tensioner Or Idler Pulley
So from reading around a lot, it seems like the chirping is from the belt tensioner or idler pulley. That said, I've not been able to find anything definitive. I tried to do the water bottle squirt test (from Gates' youtube video) and either I did it wrong or the chirp did not go away implying the issue is not the belt. While I was looking in, I could see the tensioner shaking some.
If my tensioner should not be moving, do I just need the pulley or the pulley and the mount?
- Pulley [URL] ....
- Pulley and mount [URL] ....
Also, if the above items will fix the chirp, which brand would be best?
2007 RX 350, 113K.
Chirping gets worse as it heats up. Seems to happen independent of ambient temperature. Purchased a year ago so unsure of the history of part changes.
Golf IV R32 :: Loud Clicking / Ticking Noise Coming From Timing Belt - Tensioner Looks Off
I recently had a good amount of work done to my Mk4 R32. Last night on my drive home from the stealership I ended up with a passenger headlight out and a very loud clicking/ticking noise which seems to be coming from the Serpentine belt area. After closer inspection it looks like the tensioner lines are't lined up which means my belt and tensioner need to be replaced? I'm not sure, but I have a video and this picture.
View 7 RepliesHonda - Pilot :: While Driving Clicking Noise - Replace Timing Belt Tensioner?
Six months ago my 2005 Honda Pilot got a new timing belt that was incorrectly calibrated. When the Honda Dealer test drove the car, they damaged the values. They fixed the valve damage and gave me a discount on the timing belt. I considered selling the car, but decided to keep it.
Now it's six months later. When driving I hear a "clicking noise". The dealer says that the timing belt tensioner needs to be replaced and that it would be dangerous to drive it at high speed as it is now. The clicking is caused by a worn ??? tensioner.
They claim that the incorrectly calibrated timing belt could not have caused this problem with the tensioner.
Accent RB (2012+) :: Squeaking Like Noise From Front Driver Side Wheel When Turning Left
Noticed a squeaking like noise coming from their from front drivers side wheel when turning left? Seems to only do it right after driving my car after it has been sitting for a bit. Can't make it in to Hyundai until next week, and I'm a little worried.
View 10 RepliesFord Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.