Ford F-150 (2004-2008) :: Intermediate Steering Shaft Replaced - Hard Steering
Replaced the Intermediate Steering Shaft at 114,000 miles. Symptoms felt like power steering going out but no pump noise or low fluid. Steering became hard to turn and it sometimes felt like a tie rod was letting go.
Temporary resolution was to spray the two steering shaft joints with penetrating oil (PB Blaster). That freed them up pretty well. Then I ordered Dorman part 425361 (425-361) from Rock Auto. Simple enough job. Lots of good vids on YouTube.
I don't recommend spraying the steering shaft joints as preventative maintenance. Penetrating oil will get into the needle bearings and break down the bearing grease. That will cause the joints to fail over time.
Two side benefits, the truck steering is much smoother and small road bumps and potholes are much less noticeable. Feels like it was when new.
Ford Super Duty (1999-2016) :: 2004 F350 - Steering Wheel Sticky After Cleaning
I have an 04 lariat f350 and after cleaning the steering wheel it is a bit sticky.... What the material is?? Or how to resolve the sticky issue??
View 8 RepliesFord F-150 (2004-2008) :: OEM Steel Brake Line Rubbing On The Steering Shaft
Im working on my buddies 2005 F150 FX4. In the midst of buttoning everything up and calling it a day I happen to see fluid dripping. The OEM steel brake line had been rubbing on the steering shaft and while doing the brakes, must of busted through all of the way.
I have been to Advance and Napa at least 4 times trying to match stuff up. Nothing works from either of them.
Called Ford and talked to a parts guy who lacked general automotive knowledge and finally had to pull up there diagram to show him the correct part. He told me that part is discontinued and cannot be ordered.
It is #2264 in this diagram.
2005 Ford F-150 Front Brake Hydraulic Hose | FordParts.com
I have the factory fittings and everything to make a new line. I cannot find tube that is 5.20mm or .20". Everything I find in a roll is either 3/16 or 6mm.
The fitting is a 12mmx1.00 on the ABS brain. The caliper hose appears to be a 3/8x24. A 10mmx1.00 which is standard metric 3/16 tube nut is to big for the OEM caliper hose. A standard 3/16 flare wont seat on the caliper hose.
So it seems like what Ford did here was.... a 12mmx1.00 on a 5.20mm tube to a 3/8x24 to a caliper hose that wont seat with out 5.20mm tube.
Ford Ranger / B-Series :: 2000 - Burning Gear Oil Smell From Right CV Shaft?
In 4 x4 ( 2000 ford ranger 4.0 ) and drive for a while I can smell gear oil burning off the exhaust looks like it's coming out of the right cv shaft? Is there a seal that goes first That's bad?
View 6 RepliesToyota - Corolla :: 2000 - Cleaning Of Valve / Throttle Body?
Car is 2000 Corolla with 60k miles that sometimes has a low idle (sometimes) when driven for the first 15 minutes early morning. Especially when accessories turn on, the RPM drop suddenly to 600 and recovers to 623 then back to 650rpm. After 15 minutes, everything works fine (normal 650 rpm)....my guess is the IAC Valve/throttle body needs cleaning.
What exactly do I need to tell me mechanic? That both the IAC Valve and throttle body needs to be clean? Also, after "cleaning it using a spray"....should he wait till the "spray dissipates"? What happens if it goes inside the engine?
Ford 6.7L Power Stroke Diesel :: 2000 - Front Drive Shaft And Axle Locked In?
I am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 RepliesFord F-150 - 1997-2003 :: 2000 - Knocking / Replaced Crank Shaft Now Water In Radiator - No Power?
I bought this truck an it ran good then one day it started knocking really bad so i replaced the crank shaft an bearings. Put everything back together started the truck an it ran like crap an i just happened to check the oil an it is milky. All the water in y radiator is now in the motor oil an truck has no power...
View 2 RepliesCamry :: Knock Heard From Intermediate Steering Shaft
It appears the knock I heard isn't from the suspension, its from the intermediate steering shaft. You can actually feel it in the steering wheel. The vehicle is out of warranty. I still don't understand why toyota wont fix this since its a known flaw in the design of the car.
View 9 RepliesLexus SC430 :: PPE Headers - Steering Shaft Removal?
I'm doing PPE headers right now but stuck with steering shaft I removed 1 bolt in the car and 2 in the engine bay on the shaft.... but there's just not enough give to slide the shaft out. I need a crash course on this thing pictures photos or whatever would be nice.
View 1 RepliesLexus LS 2007+ :: Rust On The Inside Of Steering Shaft?
As you can see in the picture below, there is rust on the joint.. I have two identical 2008 LS 600 HLs. Only one has rust on the joint. Both have rust on the bracket on the left.. It seems unusual that Lexus would have rusted parts on the inside, so quickly.
None of us would think of checking it. The location is above the accelerator pedal, under the steering. I saw it accidentally, because someone asked me to take a picture of the two buttons in that location (one turns pcs off and other is for TPMS).
Here is the link to the picture : [URL] ....
Ford Super Duty (1999-2016) :: 2000 F350 - How To Correctly Install Front Drive Shaft
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesCamry :: 2009 - Steering Shaft Making Loud Noise
I have a 2009 Camry 5Speed Manual and have had a noise and loud thud coming from my steering whenever i turn the wheel when I am accelerating out of first gear when disengaging the clutch and turning the wheel. For example, if I am in a parking lot and am traveling at extremely low speeds and turning the wheel while in first gear I can hear and feel a thud in the steering wheel.
View 2 RepliesGolf IV / Jetta IV :: Steering Rack And Pinion Shaft Connection
I just finished my first MK4 steering rack replacement (don't work on too many VWs), and when I placed the steering shaft from the column onto the shaft from the rack and bolted it down, there was still some clearance (see photo). I was able to get the bolt tightened down ok, but the clearance is bothering me.
View 2 RepliesCamry :: 2006 XLE Has Steering Wheel Clunk / Shaft Making The Noise?
Not a huge deal, but my '06 XLE has a steering shaft clunk, I'm assuming that it's the collapsible shaft making the noise. I notice it, I don't dare mention it to my wife who drives the car. I'm at about 60K and I have read about the problem before, I was just wondering if there was ever a TSB on it.
View 8 RepliesDodge - Durango :: 2002 - Intermediate Steering Shaft Making Noise
Truck is 2002 2WD 4.7L Durango and around 164K
I am looking to replace the intermediate steering shaft as it making noise it seems they are common to this problem due to a weak U joint. The problem I have is I can track the correct part. Here is what I have research so far:
Have found this one 55351246AA but it says it will not fit.
Also found the Dorman 425-257 but it says is for 4WD but it reference to this OE part numbers: 55351208AA, 55351208AB, 55351246AA
Have try the Dodge parts website but that is even more confusing. I have already replace the ball joints, wheel bearings and inner and outer tie rods and this is the last part that needs to be replaced if I can track the correct one.
Ford Super Duty (1999-2016) :: Loose / Binding And Metal On Metal Sound On Steering Wheel Shaft
I have a loose, binding, metal on metal sound on my steering wheel shaft. I have removed the steering wheel, replaced the clockspring, because when I removed wheel clockspring was in pieces and I thought that might be the issue. Guess not, because I'm still having problem. Other than having to remove or replace the whole steering column...
View 2 RepliesCelica :: 2000 GT - New Output Shaft Seal Leaks
I installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
Prius (2010-12) :: Clunking Noise When Turning The Steering Wheel - Replaced Intermediate Shaft 3 Times?
Our 2012 Prius with now 17,000 miles in 8 months has developed a clunking noise when turning the steering wheel, especially far to the right at low speeds.
The first time the dealer identified it as a failed intermediate shaft and replaced it under warranty. Shortly after we told them it was starting to make the noise again, but they claimed they couldn't replicate the sound and anything they heard was normal 'linkage' (whatever that is). Shortly thereafter the clunking progressed so we took it in for now the third time, and they confirmed the problem, spoke with Toyota who said we must have had a bad part, and replaced it again.
Accent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 Replies