Ford F-150 (2004-2008) :: Intermediate Steering Shaft Replaced - Hard Steering
Replaced the Intermediate Steering Shaft at 114,000 miles. Symptoms felt like power steering going out but no pump noise or low fluid. Steering became hard to turn and it sometimes felt like a tie rod was letting go.
Temporary resolution was to spray the two steering shaft joints with penetrating oil (PB Blaster). That freed them up pretty well. Then I ordered Dorman part 425361 (425-361) from Rock Auto. Simple enough job. Lots of good vids on YouTube.
I don't recommend spraying the steering shaft joints as preventative maintenance. Penetrating oil will get into the needle bearings and break down the bearing grease. That will cause the joints to fail over time.
Two side benefits, the truck steering is much smoother and small road bumps and potholes are much less noticeable. Feels like it was when new.
Camry :: 2010 - Steering Wheel Makes Clunking / Clicking Noise When Turning Car
I've recently replaced the power steering pulleys and belts. Now when i turn car, it makes a clunking /clicking noise and sometimes the power steering tugs back a bit. 2010 camry.
View 3 RepliesDodge - Durango :: 2002 - Intermediate Steering Shaft Making Noise
Truck is 2002 2WD 4.7L Durango and around 164K
I am looking to replace the intermediate steering shaft as it making noise it seems they are common to this problem due to a weak U joint. The problem I have is I can track the correct part. Here is what I have research so far:
Have found this one 55351246AA but it says it will not fit.
Also found the Dorman 425-257 but it says is for 4WD but it reference to this OE part numbers: 55351208AA, 55351208AB, 55351246AA
Have try the Dodge parts website but that is even more confusing. I have already replace the ball joints, wheel bearings and inner and outer tie rods and this is the last part that needs to be replaced if I can track the correct one.
Prius (Gen 3) :: 2010 - Clunking Noise When Turn Steering Wheel From Left To Right
Having issues with Gen3 Prius steering column? I suddenly developed this clunking noise when I rock my steering wheel from left to right. It's steering correctly but I've never heard this noise before....
View 7 RepliesCamry :: Knock Heard From Intermediate Steering Shaft
It appears the knock I heard isn't from the suspension, its from the intermediate steering shaft. You can actually feel it in the steering wheel. The vehicle is out of warranty. I still don't understand why toyota wont fix this since its a known flaw in the design of the car.
View 9 RepliesPrius (2004-09) :: Front End Shakes After Having Intermediate Shaft Replacement
My Front Suspension NOW SHAKES; After Having the Prius Intermediate Shaft Replacement Recall done!!
I took my PRIUS to the dealer this past week and had the Prius Intermediate Shaft Replacement Recall done.
Tiguan :: 2010 - Steering Wheel Noise While Turning?
My 2010 Wolfsburg Tig makes rubbing noises when I turn the wheel but not moving. The noise sounds from the wheel shaft. The noise goes away when the car is moving. What's noise? Is it a normal noise for Tig?
View 6 RepliesPrius (Gen 2) :: Vibration / Clunking Noise In Front End While Driving With Steering Wheel Centered
The problem started a few months back and has been getting progressively worse. Unfortunately for my Prius I have been in the middle of remodeling my house so I have been neglecting the problem and now it is time to face it before something bad happens.
So, It is a 2005 Prius with 189k+ miles on it. I started getting a vibration/clunking noise in the front end while driving with the steering wheel centered. It also turns on the traction control alert and sometimes slows the car down when turning and the only way to get it to stop is to turn the wheel the other way. It started only happening at higher speeds of 65mph+ but progressively got worse until it now happens as low as 35mph.
I thought that it was the drive axle as it seemed to be characteristic of that with the vibration (When the problem first started it seemed to only happen when accelerating, but now happens all the time), so I replaced the LH drive axle as well as the sway bar tie rod (The joints were very worn and loose), but the problem still exists.
Camry :: 2009 - Clunking Sound When Turning Steering Wheel
So my 09' Camry now has 130K KMs on it and for the last few months I've had an issue where when I turn the steering wheel (at rest and while moving) there is a clunking sound and feel in the steering wheel at various spots in the steering wheel rotation.
I'm worried the u-joints (if it uses them) in the steering column are worn out and might need replacing/lubricating but I'm not sure how to address the issue without an expensive Out of warranty visit to the dealer.
Honda Odyssey :: 2010 EXL - Whining Noise When Turning Steering Wheel
My 2010 Honda Odyssey EXL recently began making a whining noise that seems worse when turning the steering wheel. When in the shop for routine maintenance a few weeks ago they noted a leaking power steering suction hose although at the time it was not making any noise. Is this a likely cause? Unsure what it was I tried spraying belt dressing on the serpentine belt and it seemed to work. There was no whining for a couple days. Now it's back.
View 2 RepliesCamry :: 2007 - Clunking Noises When Turning Steering Wheel To Left
My 2007 Camry makes clunking noises when I turn the steering wheel to the left mostly. This happens most often when the weather is warm and hot but not during the winter time.
The noise seems to come only from around the steering wheel area inside my vehicle. Hence, I don't think it has to do with the CV Joints or anything like that but the steering wheel unit.
Camry :: 2006 XLE Has Steering Wheel Clunk / Shaft Making The Noise?
Not a huge deal, but my '06 XLE has a steering shaft clunk, I'm assuming that it's the collapsible shaft making the noise. I notice it, I don't dare mention it to my wife who drives the car. I'm at about 60K and I have read about the problem before, I was just wondering if there was ever a TSB on it.
View 8 RepliesCamry 2012+ :: SE - Popping / Clunking Noise When Reversing And Turning The Wheel
I've owned my 14.5 camry se 4 cyl since may and a few weeks into owning it i noticed a pop/clunk coming from the front passenger side while reversing and turning the wheel. So, finally got some free time to take it into the dealer today and dropped it off. Also, when letting off the brakes you can hear like a creaking noise, almost like the brakes are metal to metal but it only happens LETTING OFF the brakes?
My service advisor says supposedly the "creaking" noise when letting off the brakes is normal. I told him i really don't believe that lol and asked to test drive another new camry on the lot which is being arranged for tomorrow. In the meantime he says they're gonna look at it either way.
Prius (2004-09) :: 2005 - Steering Making Clunking Sound When Turning?
Just bought an 05 yesterday. It has 193k. The steering seems to have some play and an occasional clunking sound when turning the wheel. I do not know of a dealer or an independent shop that will give me an honest opinion or quote..
View 2 RepliesCamry 2012+ :: Clicking Sound When Turning - Front Drive Shaft Assembly Replaced?
On my 2012 Camry XLE with 22,500 miles, just had the drivers side drive shaft assembly replaced, under warranty. Was getting a clicking sound when turning. Not too happy, car comes off warranty in September. They also updated computer on a recall for the torque shutter.
Then he tells me I need an oil change (was just done, oil shiny clean). He said oil looked dirty. Also said I needed a fuel injection cleaning (at 22.5k?), and new tires. OEM tires are garbage. Wheres the Toyota quality and integrity?
Passat (B6) :: Clunking Sort Of Noise From Steering Wheel
So I just came back from the stealer(Koeppel). I had them check out my car because it was making this clunking sort of noise from the steering wheel. When you turn the steering wheel, when it is turned straight, left and right, it makes this obnoxious noise. It sounds pretty bad.I thought it might be an axle problem or possibly a bearing. Now heres the funny part. My dealer says that it is normal. They said they called VW technical support and they told them that the way the rack&pinion was built on our cars, that causes the noise. He said i can show you 3 other Passats that make the same noise. I didn't bother because i did not have the time. I am going to go tomorrow again to see if they can find anything else on it. If they dont, i am going to ask them to show me the other Passats with the same noise.
View 15 RepliesPrius (2010-12) :: TPMS Light Went Off After 4 - 5 Times Of Turning The Car On / Off
Last night the TPMS light came on on my month old 2010 Prius. I checked all the tire pressures and they we @ 38 rear and 40 front.
TPMS light went off after 4-5 times of turning the car on/off.
What might have been the problem? Is it something I need to be concerned about?
Subaru - Brakes - Steering - Outback :: 2008 - Whining Noise In Engine / Clunking While Turning?
My outback has 57k miles on it and already needs the front struts and rack replaced (diagnosed today at the Subaru dealership). The car has been making a whining noise in the engine and has been clunking when making turns for the past week. I have also noticed it hasn't been taking bumps as smoothly. They told me that both ends of the rack are leaking and both front struts are leaking. My husband did admit to hitting the curb on the driver side front tire pretty hard while making a u-turn about a month ago, but all other driving is pretty standard. Yes, we drive on dirt roads in the mountains a few times a year for hiking, but don't drive in a manner that I consider wrong. Did the u-turn incident cause this? (hard to believe that would affect both sides of the rack and struts).
View 2 RepliesGolf V R32 :: 2004 - Intermediate Shaft Outer Gear Just Worn Completely Out
My 2004 r32 has 160k miles, cam positioning lite wouldn't clear-outer (small) chain intermediate shaft gear just about worn completely out. Are timing specs for cams,crank, intermediate shaft available, also torque specs? Iread the 12v chain diy thread, but I doubt they are the same.
View 1 Replies