Camry :: 2002 V6 Automatic Transmission - Check Engine Light Came On With Code P0770
I have a 2002 Toyota Camry V6. The warranty expired in Feb 2007. The car has only 67,000km.
The check engine light came on and the code is P0770, Solenoid E malfunction. The problem was first reported at 43,000km, when the car was still under warranty but only a transmission flush was performed and the code was reset.
I wrote Toyota and after almost two months they told me they do not cover it because is out of warranty and I do not qualify for the Goodwill program. I tried again to tell them that instead of fixing the root of the problem they temporarily covered it, but again I got a NO. No comments about the mileage, time, etc. Just the car is out of warranty and I'm out of luck.
Ford F-150 (2004-2008) :: 2007 4.6L V8 - Code P0401 - Insufficient Flow - EGR Identification
I am preparing to combat the old P0401, Insufficient flow issue. While looking at the steps in Alldatadiy the very first decision essentially forks on "EGR System Module" or "Others".
I am just guessing that, since the choice is there, some engines will have one and some will have the other. But I thought I'd come here and see if I could learn a little more about it.
How can I tell what my truck has? I'm sure there is some difference...
Camry :: CE 2000 5S-FE With Code P0770 And High Idle Speed
Camry 2000 CE 102,xxx miles. My car died in Jan 14, after have P0770 for while, only Reverse gear work. The mechanics said the tranny need to re-build. I had him bring the tranny to tranny shop to re-build ($1650), then the code still pop up. Brought it back, they said the ECU needs to be reset. I had the car next day then that code pop up again!
They replaced the Solenoid E. The code is still there. Brought the car back, they took the tranny to rebuild it again. Drive the car for a day, the darn code pop up again, now they blamed on the ECU. Ok my mechanic guy replaced it at my own cost for part ($150) but the code is still there. This time they blamed on the high idle rpm approx. 1600-1800. My mechanic tried to fix the high idle speed so the tranny stop blaming other causes. He cleaned IAC valve, replace O-rings (I don't remember the location of them) then he said whenever he inserted the new ones, they start to crack!
Ford - Explorer :: 2008 - Stuck In Gear - CEL On With P0770 Code?
Last night while driving, my transmission made a pretty severe clunk, but then appeared to act normal. However, a check engine light came on so I pulled over immediately as I was literally at the entrance to a gas station.
I looked under the vehicle, under the hood, saw nothing leaking, nothing obviously broken etc. So got back in and started the engine, went to shift into reverse and the transmission clunks, same going from N into D.
I limped it home, but while driving noticed that it was not shifting but stuck in one gear.
This morning I scanned for codes and the only one showing is P0770 Shift Solenoid. I searched this forum though and get 0 results on that code, searching Google is also surprisingly vague. I believe (could be wrong though) that I have the 6R60 Transmission, it is a 2008 Explorer with the 4.6L V8.
Where to check first? When I get time I am going to check the fluid level, but could not last night as there is no dipstick!
Lexus GS 2006-11 :: GS300 Engine Fault Code P2757 - Transmission Lagging
During low rpm cruise and light throttle acceleration below 2000rpm the transmission feels like its lagging or doesn't engage until after like a second or two after you press the gas pedal down. Been happening the past couple months and I would like to find a fix for it instead of buying a used trans or new trans.
Just picked up this code the other day as well.
P2757: Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance or Stuck Off
Recently changed the fluid over a year ago with Toyota ATF @ Longo Lexus. Car has 140k+ miles on it.
Toyota - Tacoma :: 2004 V6 - P0304 Code Won't Go Away
I changed the coil on cylinder 4 on my 2004 V6 Tacoma and the p0304 code keeps coming back along with the hesitation and missing when I accelerate. The wires were replaced a month ago. What now?
View 3 RepliesToyota - Tacoma :: OBD2 Gives Same Code Twice - P0420?
My Toyota Tacoma is reporting (via an affordable OBD-II scanner) the same P0420 code: First as a regular code, then as a pending code. What could that mean?
View 6 RepliesToyota - Tacoma :: Transmission Won't Shift Into 4th Or 5th Gear
I have a 94 4x4 v6 Toyota pickup the check engine light came on while I was driving it 20 miles later it shifted from 5 into 4.the tranny shifts smoothly into the other gears with no problem but now it won't go in the 4th or 5thmy transmission fluid is passed a full line...
View 1 RepliesToyota - Tacoma :: Transmission Click In Reverse Only When Back Up
I was told that fixing the reverse gear can be done without dropping the transmission. Is there anywhere I can see a video of this? My shifter locked up out of nowhere and when I got it back loose it started clicking in reverse only when I back up.
View 1 RepliesToyota - Tacoma :: Auto Transmission Aggressively Downshifts
My 2011 toyota tacoma auto transmission downshifts on any slight decline, even to the point of losing traction in the rear end if I am on slippery pavement. How can I disable the electronic engine brake?
View 5 RepliesToyota - Tacoma :: 2000 - Transmission Squeak When Let Off The Accelerator
My 2000 Toyota Tacoma 5 speed sometimes makes a squeaking noise when I let off the accelerator, most noticeably at speeds of between 25-35mph. If I press on the accelerator, the squeaking stops...it seems like it has to be related to the transmission. I was told it may be the U joint...
View 1 RepliesTacoma :: P1071 Error Code - Bank 1 System Too Lean
I've searched for this and haven't come up with much other than the same error code for a bunch of other vehicles, and a bunch of different responses. My Tacoma is a 2000 PreRunner, 3.4 liter engine.
The exact code I get it is:
P1071
bank 1 system too lean
What this could be?
Toyota - Tacoma :: 1990 Transmission Won't Shift Into 1st When Clutch Depressed
So, I bought the truck used and everything about this truck is great minus the shifting difficulties in first. With the truck at a dead stop, the clutch depressed, and the shifter in neutral it can be near impossible to shift into 1st (it's possible with a lot - emphasis on a lot - of force). No grinding, clashing, knocking in the shift knob - it just wont go into gear. I can shift into 2nd-5th and reverse without too much difficulty. If the truck is in motion, once the vehicle gets between 2-5mph I can easily downshift into 1st. However, if I shift out of 1st and let the truck sit for, say, 5 seconds it is often very challenging to get the truck back into 1st.
I have tried to look up this problem online with limited success. What I found was it could be caused by:- something wrong with the clutch installation- a need to bleed the clutch (it's hydraulic and, although the reservoir is full, the fluid is a bit dirty)- perhaps a faulty clutch master cylinder- play in the clutch linkage- a broken spring in the pressure plate- a bearing that is starting to go out- worn synchros in 1st.
I am a machinist, not a mechanic, so it's hard for me to evaluate these ideas (beyond the cost associated with each). Given my limited knowledge of transmissions and my good mechanic friend's opinion, I think it's a broken spring in the pressure plate.
1990 Toyota Pickup 4x4 manual transmission. This is the original transmission in the truck, it has not been rebuilt (but has been maintained with regular fluid changes), and has a tad over 158,000 miles on it.
Golf IV / Jetta IV :: 2004 TDI - Coolant Leak From The Bottom - Hose Identification?
I have coolant leaking from the bottom of this hose on my brothers car. I am not very familiar with the BEW's as I drive an ALH. Just looking for info about part number or name on this hose so I can get a new one. Has a part number MH3364 on it but that is not working anywhere.
View 2 RepliesFord Escape / Hybrid :: 2001 V6 - Emergency Vacuum Hose Identification
I simply cannot find a proper and complete vacuum diagram for this 2001 Escape V6. (The sticker has been removed from the car.)
The car is hard to start - very hard, but once warm it manages to run ok. There vacuum hose way down low, on the back of the block and under the starter, impossible to see but if my fingers aren't lying it's very near the knock sensor? This hose is rotten and disconnected at the top - it's just laying there kinda under the throttle body.
For the life of me I cannot a) identify what the hose goes to and b) figure out where to plug it back in. There are no empty ports I can find anywhere within reach of the floppy end of the hose.
Tacoma :: 2000 V6 Check Engine Light Code P300 / P306 - Cylinder 3 And 6 Misfire
2000 Tacoma v6 has has always ran good, but has check engine light code P300 & P306. cly 3 & cly 6 missfire, lean bank 1. Vacuum test showed no problems.
I've changed plugs & wires, switched coils around cleaned mass air flow sensor, checked timing. Ran Seafoam through intake, and gas tank. Check engine light went out for about three miles, then came back on. What else can I do to keep that blinking check engine light off?
Tacoma :: 1997 3.4L Toyota - Multiple Camshaft Position Sensor Failures / Code P3040
I have a 1997 Toyota Tacoma 3.4L ... After having some problems a week ago with the truck dieing at every stop sign or any time my foot wasn't on the gas. Eventually the truck would not start at all. I finally got a CEL that gave me P3040 (Camshaft Position Sensor Circuit Malfunction) So I changed out the sensor and the truck fired right up and ran for 3 days.. Now the truck does not start again and I am getting the same CEL code.
View 1 RepliesCamry :: 2002 - Tranny Is Slipping / CEL P0770 And P0765 Codes
I did a search on the CEL P0770 and P0765 codes and I find plenty in regards to the light on but every post I have seen, says the tranny is working fine. Not the case with mine. Tranny is slipping, and if you let it sit for 30 minutes or so, it will run fine then start surging and slipping. Got to where I couldn't get it to move at all. It says B, D E trans shift solenoid for the codes. I don't want to put in this new solenoid and have not fix the issue. Is my tranny toast? Seems electrical since it will work fine once it sits for a bit. Plus, with the OD disengaged, it seemed to work fine, but even then it was acting up? I bought it used with 140k and don't know if tranny was serviced or not. I think it has due to lots of oil change receipts etc from the past 4 years..
View 9 RepliesTacoma - Gasoline :: 2003 - Check Engine Light Returning A Code For Failed Up-stream Air / Fuel Sensor
My '03 Tacoma Prerunner V6 has 116K miles and recently lit up its Check Engine light, returning a code for a failed up-stream air/fuel sensor. I recently drove across country, using many different fuel formulations ranging from CA gas to midwest ethanol to whatever they put in the gas here in the NY-NJ area (a mystery ingredient that seems to turn motorists irate and confuse their horn as a turn signal.)Anyway- age, or fuel, what killed the sensor? If fuel, will it happen again by time I get back west?
View 2 Replies