Toyota - Tacoma :: Transmission Won't Shift Into 4th Or 5th Gear
I have a 94 4x4 v6 Toyota pickup the check engine light came on while I was driving it 20 miles later it shifted from 5 into 4.the tranny shifts smoothly into the other gears with no problem but now it won't go in the 4th or 5thmy transmission fluid is passed a full line...
View 1 RepliesFord - Escort :: 1993 - Unable To Shift Into Gear With Clutch Depressed To The Floor
I have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
Ford Transmission :: 1998 - Buckles When Clutch Depressed But Won't Stall?
I have a 98 f150 with a 4.2L V6 and a 5 Speed M5R2 manual transmission, I recently got a rebuilt trans for my truck. I installed it with no issues, while my truck was still on jack stands I tested it out, it shifted into every gear no problem but after I took it off the stands and pulled it out of my backyard, when I take off in 1st its fine with the clutch being slowly released, but as soon as I let go of the clutch the truck just buckles and some times tries to flat out stop.
I'm not sure if I have a Clutch issue, Transmission issue or axle issue, when I tried it out on jack stands I had the stands supporting the rear on the axles so some of the weight of the truck was and the rear axle and it didn't buckle then so I wouldn't think it'd be the axles but when it was on the ground it'll buckle. I even had someone move the truck forward and release the clutch slowly until in was fully releases and looked underneath and saw the axle buckle upward,
What the issue is it only does that when the clutch is released or if I'm lucky enough to release it without buckling once I go to shift to second and press in the clutch the whole truck just comes to a complete stop without the engine stalling. I thought maybe it was a clutch issue and that maybe I put the clutch plate backward(which I'm pretty sure I didn't)but even if I did, I wouldn't even be able to shift it into any gear, at least that's what I think. I bleed the clutch before taking it out so I don't think that could be the issue either.
Toyota - Tacoma :: 1999 - Clutch Pedal Intermittently Sticks To The Floor
My 1999 Toyota Tacoma (Ext Cab, 4x4 TRD) has 162K miles and now the clutch pedal intermittently sticks to the floor. I have to pull it off the floor with my toes while driving and have also felt the pedal start to pull back towards the floor on its own while the truck is in gear.
I'm looking for some wisdom as a few blogs/websites point towards a master cylinder, others say the master and slave, and my local auto shop said I need to replace the entire clutch assembly and throttle bearing. My truck is no spring chicken anymore but I'd like to keep it running for a few more years...
Toyota - Tacoma :: 2003 - Clutch Not All The Way Disengaged When Push The Pedal To Floor
The clutch on my 2003 Toyota Tacoma has been acting funny for a while. I have to pull the pedal back up with the top of my foot about half the time, otherwise it acts like the clutch isn't all the way disengaged when I push the pedal to the floor. The master and slave cylinders have both been replaced as well as the clutch pedal mechanism itself (thought it might be the spring). I adjusted the push rod a little bit and it seems to have worked slightly but it's definitely still a problem.
View 3 RepliesToyota - Tacoma :: 4 Cylinder 5 Speed - Sticking Clutch Pedal When Pushed To The Floor
I have a 2007 Tacoma 4 cylinder 5 speed. The clutch pedal started sticking about a month ago and has only happened a hand full of times. When the pedal is pushed to the floor it would stick, I thought it was hanging up on the floor mat at first but that was not the case. I went out to move the truck today and the pedal immediately stuck to the floor. Like usual I tapped the pedal kind of on the side to get it to release. the pedal then came back up. But now it wont push back in at all!!! There is only 1/2" of travel on the pedal and stops solid. It's like it is binding up on something. The spring seems to be in place the right way and nothing that I can see obviously wrong.
View 4 RepliesToyota - Tacoma :: 2001 Bucks / Jumps Like Clutch Is Alternately And Rapidly Grabbing And Releasing
My 2001 Tacoma drives well most of the time, but when in 4 wheel drive low range, low gear, in demanding circumstances like heavy snow, it will buck, jump, act like the clutch is alternately and rapidly grabbing and releasing (but I'm pretty sure it's not actually that). Tires are good. Four cylinder, standard transmission.
View 7 RepliesFord Transmission :: 1990 F150 2WD Will Only Shift Into 1st And 2nd?
1990 F150 2wd, E40AOD tranny. Will not shift past 2nd. Reverse works. Does not have compression braking. Started when pulling a empty trailer up a hill on the interstate.
View 1 RepliesToyota - 4runner :: 1990 - Loud Popping Noise From Clutch Area
I have a 1990 Toyota 4-Runner, manual 5-speed transmission. About a week ago, while shifting gears, I heard a loud "popping" noise from the general vicinity of the clutch. I did not feel anything different in the clutch, it returned to the appropriate position and didn't feel any more or less "loose." However, after the "pop" it seemed difficult to get the vehicle into first gear and second gear, and I really had to "push" it to get it into gear, but it would not grind or anything else. Also, when shifting into reverse, it would grind loudly and be very difficult to get into reverse gear. If I turn the vehicle off, put it in reverse and then start the car, it works fine, though it seems like it "sticks" longer in reverse and takes a bit more muscle to get it out of reverse and into first again.
Additionally, when the shifter is in first gear, but the clutch is pressed, it seems as if the clutch is not disengaging entirely, because the car wants to move forward slightly when I take my foot off the brake, almost as if I'm letting my foot off the clutch a bit with it in gear. All of this has been happening pretty regularly, but the car has still been driving fine. However, today, the poor thing wouldn't start. This vehicle (like many manual transmissions) needs to have the clutch pedal pressed in order to start the vehicle. Even when I press the clutch all the way to the floor, the car won't start (and I know it is not a starter/battery issue). Given the other problems with the clutch and shifting gears, it almost feels as if the clutch was not getting disengaged all the way even when the pedal was pressed to the floor, and now that it won't start, I'm wondering what is going on. Does this model have a linkage adjuster that needs fixing? Is it something wrong with the clutch fluid? Or do I need a new clutch entirely?
Toyota - Tacoma :: Transmission Click In Reverse Only When Back Up
I was told that fixing the reverse gear can be done without dropping the transmission. Is there anywhere I can see a video of this? My shifter locked up out of nowhere and when I got it back loose it started clicking in reverse only when I back up.
View 1 RepliesToyota - Tacoma :: Auto Transmission Aggressively Downshifts
My 2011 toyota tacoma auto transmission downshifts on any slight decline, even to the point of losing traction in the rear end if I am on slippery pavement. How can I disable the electronic engine brake?
View 5 RepliesToyota - Tacoma :: 2000 - Transmission Squeak When Let Off The Accelerator
My 2000 Toyota Tacoma 5 speed sometimes makes a squeaking noise when I let off the accelerator, most noticeably at speeds of between 25-35mph. If I press on the accelerator, the squeaking stops...it seems like it has to be related to the transmission. I was told it may be the U joint...
View 1 RepliesFord Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Golf VI R :: Clutch Ticking On Foot When Depressed?
I read all of the threads regarding clutch vibrations and other problems but I have 1,500 miles on my R and since day 1 I have been feeling a very slight ticking on my foot when the clutch is depressed. It gets more pronounced when I rev the engine a bit but nothing you can hear. Is this a normal feeling or should I not feel this at all.
I'm getting the APR tune next week and will do HPFP/intake soon but I need to be convinced that the Carbonio Intake is actually an upgrade from the stock intake with just a K&N filter, it doesn't look much different, the intake area looks the same as stock. I don't want to have to modify the engine cover or else I'd get the VWR intake. Any experience with the K&N vs stock vs Carbino?
Not sure if it was just the hot/humid weather yesterday but the car felt a little boggy when starting in 1st gear like it was running too rich or something. Any history of this?
BMW - 328 :: 1996 - Loud Clunk / Pop When Clutch Depressed
This is regarding my 96 BMW 328i. It has approximately 177,000 miles on it. Over the past year, I've replaced the cooling system, fuel pump, alternator and trans fluid for kicks. So, I'm understandably frustrated with it. Anyway, to my story:
On my way into work, whenever I pressed in on the clutch, it would make a loud clunk/pop and freak me out. I turned around after 1/4 of the way and swapped cars.
My mechanical skills are maybe 3 on a scale of 1 to 10. I'm not afraid of changing oil, brake pads, transmission fluid, changing an alternator, etc. But I want to have someone to blame for anything that involves anything within the engine block/head/transmission continuum.
I noticed that a heat shield was loose between the driveshaft and the exhaust. I rapped it with a hammer, and the heat shield didn't make a noise anything like I'm hearing. So, it doesn't sound like that's the real culprit here.
Passat (B7) :: Clutch Clicking When The Pedal Is Depressed
2013 tdi 6mt. I am noticing that my clutch clicks when the pedal is depressed. it does not happen when I first start driving in the morning, but it seems that once the cabin is warmed slightly it starts then clicks each and every time. It is annoying and it appears to be related to the different temps outside vs the cabin. I did not notice it during summer or early fall but it is cold here now.
View 24 RepliesGolf - Volkswagen :: Loud Pop Noise With Clutch Depressed?
I've been driving manual transmission vehicles - from my '72 Pinto to big trucks - for 40 years. This happened recently in a VW Golf I had rented: While driving down a mountain in a tunnel in Norway, with the clutch depressed, there was a loud POP noise.The clutch became engaged, and the clutch pedal did nothing. I'll spare you the details of the harrowing aftermath, the language barrier issues in the sticks of Norway and such. In the end, the rental company is charging us a couple thousand bucks for breaking their car. I maintain it was not Driver Error. My local VM service manager indicated that the Slave Cylinder on the Golf has been a problem for years, and is probably what went bad, but - as a rep of VW - is not willing (allowed) to put that in writing. The garage that fixed the Golf indicated it was Driver Error. I'm guessing everything tranny-wise got beat up when the Slave gave out, making it look like I'm a bonafide Clutch Masher.
View 19 RepliesAccent RB (2012+) :: Engine Revs When Clutch Depressed
I bought my Hyundai new in late 2011. No problems with the car (other than no spare tire???) until just out of the warranty (63,000). Had a noticeable drop in power on the highway. No warning lights. Drove another 100 miles with power intermittently dropping. Next day engine light comes on. $800 later I have a new high pressure fuel pump. All seems well. after a few weeks, I notice that the car seems to be revving when I depress the clutch to change gears, like up to 4000 rpm's. If I leave the clutch in for a few seconds it will begin to decrease. But if I shift right into gear as I have done for the last 35 years of driving, it is not smooth, jerky. This seems to happen mostly going into 2,3, and 4th gear, always going up. It never happens when downshifting. I tried tapping the brakes when shifting up, and sometimes it does seems to drop the rpm's. What it might be. It probably is related to the work that was done, but I don't really trust the dealer and want to have a little info going in.
View 1 RepliesAccent MC (2006-11) :: 2009 - Squeaking Clutch When Depressed
2009 Accent 5 speed 66K miles. This is something which I recently noticed with the onset of winter. When I depress the clutch pedal, I have a very audible squeak. Think old door hinge squeak. So metal is rubbing against metal somewhere inside the bellhousing without enough lubrication.....not good. I pulled off the dust boot on the side of the bellhousing and tried my best to push moly grease around the clutch fork stud, hoping that was the origin. The noise went away for roughly a half a day but is back in full force....funny how cars do that.
Space seems EXTREMELY limited on lubricating the proper area. Or....is this a warning mechanism built into the clutch pressure plate assembly to warn of replacement soon? While I am asking these questions, what is a good time to look into replacing the clutch? The parts for the car seem relatively cheap, if I replace the clutch assembly, I may consider replacing the flywheel and clutch hydraulics as well as a whole system replace/refresh.
That aside, is there anyway to eliminate the squeaking without having to crack open the bell housing?