Camry :: 2002 - Check Engine Light On / Code P0440
It just so happens that I got my letter from the DMV telling me I needed to get my new tags, and this is an emissions test year for my car. I was buys the last few weeks so I figured this would be a good week to do it. Yesterday.......check engine light comes on. How does that happen???
So now I'm on a time crunch. I went to Advanced Auto this morning and they checked the code. It's P0440, an Evaporative Emissions code. Any thought on what that me be, or any checklist as to what to check first? I'm fairly handy, but know nothing about cars. I'm sure I can figure it out with some instructions.
Summary: Got a check engine code of P0440, Evaporative Emissions. On a time crunch because I need to get an emissions test done. I can probably fix it myself with some direction.
Camry :: 2002 V6 - Check Engine Light Came On While Driving On Freeway / Code P0128
I have a 2002 v6 Camry with over 270k on it. Today the Check engine light came on while driving on the freeway. When I got home I used my scan tool and it gave me the following codes.
P0128, P0440, P0446 and P0440, P0441, P0446 pending.
I understand that the 128 has to do with coolant temp and that the other codes are evap system related.
What I'm trying to figure out is what might have caused them to all occur at the same time. I know once with my 98 Camry it threw a P0125 which had to do with coolant temp issues but it also threw several other codes for a bad 02 sensor and the 125 was just a false code (replaced the 02 sensors and they went away). If this 128 is possibly a false code or if I also have a bad thermostat/sensor on top of an evap system issue.
Also. coolant level is good and I checked the gas cap and insured it was on tight, reset the codes and am waiting to see what comes back.
Ford Ranger / B-Series :: 1996 2.3L Automatic - Check Engine Light Came On / Error Code Is P0141
My 1996 Ranger runs ok but my check engine has come on. Using a scanner tool, indicates my cat monitor wont go to ready state and my error code is P0141. According to my research it indicates one of my 02 sensors. How to determine if its the one before or after the cat converter? About 6 months ago I had an exhaust leak repaired around my converter so I know I cant return it under warranty . If its the rear sensor , It looks fairly easy to replace but the front sensor looks a bit cramped.
View 6 RepliesTacoma :: Code P0770 - Transmission Fault Identification
I own an '02 Toyota Tacoma v6 3.4L 4-speed automatic. After a 2-hour highway drive (not too common, small town) the other day, I started to experience transmission issues (wouldn't always switch gears properly), and the check engine light came on. My scanner indicated P0770 (Shift Solenoid E Malfunction), a transmission fault.
I've spoken with my mechanic, and I've done some research online. My understanding is that it could be a shift solenoid, the valve body, the torque converter clutch, or even just low transmission fluid.
I have owned this truck since '05/28k miles. It now has 95k miles. At about 35k, the dealership installed a new transmission (maybe the former owner was a city-driver, or something), and I had basic dealer transmission service about 30k miles ago. I have an appointment to take it to a local shop (a Ford authorized service center, that also services other makes/models) in a few days.
Except for infrequent highway driving, I don't drive the vehicle "hard" at all. I have the vehicle fully serviced by the dealer at recommended intervals. I have been advised that if this fix requires more than basic transmission service, that I should take it to the dealership (factory tools, etc).
These are some observations about the malfunction:
1) The engine/transmission is still cold (just started the engine). I shift from P to R, to back out of my driveway. The transmission seems to be "stuck" in neutral/park. 5-10 seconds pass, finally transmission engages R gear. Switching from R to D, vehicle operates normally.
2) While driving normally, I accelerate steadily from 20-40mph. The transmission hesitates before switching from 2nd-3rd gear (peaking at 3k rpm, holding steady). When I take my foot off the accelerator slightly, then re-apply it, the vehicle shifts. (EDIT: Subsequent to this same post on another forum, I have been told that first gen Tacomas often have a cold tranny 2nd to 3rd shift hesitation, and I have seen it before, but it's arguably more noticeable since this recent problem developed.)
The transmission has only 60k relatively "easy" miles on it.
Camry :: CE 2000 5S-FE With Code P0770 And High Idle Speed
Camry 2000 CE 102,xxx miles. My car died in Jan 14, after have P0770 for while, only Reverse gear work. The mechanics said the tranny need to re-build. I had him bring the tranny to tranny shop to re-build ($1650), then the code still pop up. Brought it back, they said the ECU needs to be reset. I had the car next day then that code pop up again!
They replaced the Solenoid E. The code is still there. Brought the car back, they took the tranny to rebuild it again. Drive the car for a day, the darn code pop up again, now they blamed on the ECU. Ok my mechanic guy replaced it at my own cost for part ($150) but the code is still there. This time they blamed on the high idle rpm approx. 1600-1800. My mechanic tried to fix the high idle speed so the tranny stop blaming other causes. He cleaned IAC valve, replace O-rings (I don't remember the location of them) then he said whenever he inserted the new ones, they start to crack!
Camry :: 2002 - Tranny Is Slipping / CEL P0770 And P0765 Codes
I did a search on the CEL P0770 and P0765 codes and I find plenty in regards to the light on but every post I have seen, says the tranny is working fine. Not the case with mine. Tranny is slipping, and if you let it sit for 30 minutes or so, it will run fine then start surging and slipping. Got to where I couldn't get it to move at all. It says B, D E trans shift solenoid for the codes. I don't want to put in this new solenoid and have not fix the issue. Is my tranny toast? Seems electrical since it will work fine once it sits for a bit. Plus, with the OD disengaged, it seemed to work fine, but even then it was acting up? I bought it used with 140k and don't know if tranny was serviced or not. I think it has due to lots of oil change receipts etc from the past 4 years..
View 9 RepliesFord Transmission :: Check Engine Light On / OD Light Flashing Sometimes - Code P1747
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesIntrepid :: Check Engine Light Came On - Transmission Code P0731
My wifes 1998 Intrepids' Check Engine Light came on yesterday, and while she was turning into the driveway the car stalled. It would fire right up again, and drive normally, but when she went to pull into the driveway again it stalled.
I took it into the shop, and they read the computer and thats when the P0731 code showed up.
P0731 Incorrect gear ratio # 1
When I went to bring it home, I then noticed that the speedometer was not working, and the tranny wasn't shifting out of 1st gear. The tranny fluid is clean and not burnt.
Taurus :: 2002 SES Check Engine Light On And Code P1451
Check engine light on and code is P1451. I have been told its one or all four things:
1. Gas cap,
2. Evap Canister vent solenoid,
3. Evap purge solenoid,
4. Evap canister.
I am trying to fix this problem on the Taurus. I have changed the Gas cap and this did not solve the problem. The other three things on the list: Are these three separate things? Or are they part of the same thing?
Camry :: 2002 - Check Engine Light Not Coming On
I have a 2002 4 cylinder Camry, and I've been having trouble with the EVAP test completing. I've been running the EVAP test to the letter, with no success, so I figure the problem might be dependent on something else not completing.
I used to get the occasional check engine light for loose gas cap. So a few days ago I intentionally left the gas cap VERY loose (it's essentially just sitting in the filler nozzle). But I'm not getting the check engine light. I think that the gas tank pressure test may not be running, and that may be why I can't get the EVAP test to complete successfully.
Conditions: The gas level is about 1/2 full, and the ambient temperature has been around 20-35 degrees F.
I'm having a hard time searching. Most search results deal with how to resolve the loose gas cap problem. The check engine light is not burned out... it comes on briefly when I start the car!
Camry :: 2007 - Check Engine Light Comes On With Code PO441
My wife's car has 83000 miles on it. We bought it as a factory certified pre-owned vehicle with about 1800 miles on it and it came with the warranty. For the last two years the check engine light comes on with code 441 I don't worry about it till time to get inspection sticker here in Texas. I have been about to reset the computer and drive it till the computer is ready to be inspected and it has passed for two years. Now it won't reset and I have tried to test the vacuum switch and it seems to click when I apply voltage but light won't go off. This code can cost up to about 2000.00 to try and detect. I am not interested in having the dealership keep guessing on my dime.
View 2 RepliesCamry :: 2003 LE Check Engine Light Code P0031
I own a 2003 Camry LE. I went to Autozone to find out what the check enginge light was for and was given P0031. When the service person checked it out on the computer he said the probable causes were:
1) open or short circuit conditions
2) poor electrical connections
3) failed oxygen sensor
4) EFI relay fault.
I asked how it could be narrowed down and he said it I would have to get the car checked out.
Camry :: 2003 V4 - P0128 Check Engine Light Code
I'm getting a P0128 code on my 2003 V4 Camry. Autozone diagnosis says it's either
a) coolant low level
b) sensor not working correctly
c) thermostat not working correctly.
As part of 90k mile check about 3500 miles ago, the mechanic replaced the coolant. I didn't check the coolant after he had replaced it but I just checked it today and it's about 1 inch below the full level. Is this normal coolant usage considering that it's been about 3500 miles and 3 months since it was last filled?If the coolant level is okay, then how do I figure out if it's the sensor/thermostat?
Toyota - Camry :: Check Engine Light Came On For Code P0446
2001 Camry 4 cylinder. Check engine light came on yesterday. Advance Auto pulled out the code P0446 for the evap. emissions system vent circuit.
The car has no symptoms other than this and is current on all maintenance, but obviously it is a 10-year old car and so it goes.
Windstar :: 2002 - Car Running With Blinking Check-engine Light / Code P0306
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
Prius (2001-03) :: 2002 - Suddenly Get P1430 Code With Check Engine Light
Suddenly today, I get a "Check Engine" light while driving. Scangauge II says it's a P1430 error. I found two different suggestions, but where these are located on the car.
P1430-Electric Air Pump secondary Failure
P1430 -Vacuum Sensor for Adsorber and Catalyst System Circuit Malfunction
Sonata I45 (YF - 2011+) :: Engine Check Light Code, P0711 / Transmission Shift Occasionally
I own a 2013 Hyundai Sonata. Two months ago I realized that my transmission shift occasionally while I am driving, especially when the weather is cold and I park my vehicle for more than one day. Then my engine check light came, after two days it went off. I went to the dealership and ask for a multi-point inspection (without telling the inspector the transmission problem), they recommend a transmission fluid flush, then I went to an auto part shop to ask for reading engine check light code, they see P0711. After researches online, I understand this code is about transmission fluid or transmission fluid sensor defect.
My question is that, would a dirty transmission fluid cause the P0711 code, as some people stated online ?
Toyota - Camry :: 2002 - Check Engine Light Went Out / No Codes
Car: Toyota Camry 2002 .. Mileage: 150K
Symptom:Check Engine light went on a few days ago.
Checked codes and got these (3):
1) P0420
2) P1310 and
3) P0420 P ("Pending" ?)
I also checked I/M Readiness and got these suspicious-looking values:CAT: NOT RDYEVAP: NOT RDYO2S: NOT RDYH02S: NOT RDY
NOTE all the other I/M values were N/A
Researching the Codes, it sounded like Ignition, and possibly the O2 sensor on the Catalytic Convertor. I had just had some engine work done by the dealer -- actually, replaced spark plugs -- so I figured to go back and bitch him out for screwing up my car.
A few days later, before I could engage my Rage, I went back and re-scanned. First I noticed the CEL was now OFF. Scanning, I now I get "NO CODES", and all the I/M values are now N/A; No more "NOT RDY".
What do you all make of this? Should I be concerned now that the CEL is Off, and I get No Codes with a scan?Or maybe I should take it to AutoZone for their free CEL diagnosis -- would their machine be more thorough than mine (Autel MaxioScan 300)??
Camry :: Cleared Check Engine Light Three Times - Code PO240
2002 Camry 4 cylinder. I've replace the o2 sensor the one in "Bank 1". I've cleared the check engine light three times now and it still comes on about 30 plus miles. Do I need to reset the ECU? Or replace the catalytic converter?
View 11 Replies