Santa FE SM (2001-06) :: 2004 - Clunking Noise In Drive Or Reverse
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 RepliesAccent LC (2000-05) :: 2001 GL Transmission Shifting Hard Into Drive
I have a 2001 hyundai accent GL the transmission has started shifting hard when it shifts into drive. It shifts fine and smooth from first to second but when it shifts into drive it hits drive hard and sometimes it acts like it doesn't want to shift and if you let up on the gas it will go ahead and shift, but when it shifts to overdrive it seems fine but hits hard when it down shifts back to drive. Also I have noticed a couple times when it goes to shift into drive the engine seems like it revs up some but when you let off the gas it goes ahead and shifts.
View 3 RepliesSanta FE SM (2001-06) :: Transmission Shifting Hard Around 40 Mph On Freeway
I just got a 2004 hyundai santa fe 2.7l 2wd model with only 92k miles that I just bought off of Craigslist anyways when im on flat ground and cruising through town the transmission shifts perfectly. However when i went up an incline to get on the freeway it shifted hard around 40 mph but after i got back on flat ground again I got caught up in bumper to bumper traffic and once it cleared it shifted perfectly all the way to freeway speeds of approximately 70mph. Then after getting off the freeway and picking my friend up when i went to get back on the freeway (another incline) it shifted hard again around 40mph.
View 15 RepliesSanta FE SM (2001-06) :: Shifting Really Hard Into 2nd Gear When Going Uphill
I have an '03 AWD, automatic Santa Fe and it started shifting really hard into 2nd gear when going uphill recently. It also seems to take a while to shift into 2nd from 1st, but it doesn't bang like it does when downshifting.
In other threads on this site is seems like either the throttle position sensor or shift solenoids may be responsible for this. What's causing it, and how to go about fixing it?
Camry :: 2004 Clunks Very Hard When Shifting Into Reverse
I have a 2004 Camry 4cyl with and Automatic Transmission. 193,xxx miles. I bought the car with 165,xxx miles. From time to time the transmission would take a little longer than normal to shift from 1-2 or 2-3. It has also had an issue with locking up the torque converter at speeds around 50 MPH which seems to bog the engine some. An adjustment of the foot on the gas pedal fixed both of these problems. (I just let up a little or pressed a little harder)
Well on friday it did something weird. It now clunks very hard when shifting into reverse. Also when in drive it seems to be in 3rd gear. The engine revs very high before the car starts moving but then it seems to run fine once moving and up to road speed.
I have heard that the Transmission may be controlled by its own Computer unit. Is that true? How do I get codes from it?
I have run my scan tool through the OBDII port and get no codes at all.
Subaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
Santa FE SM (2001-06) :: Auto Transmission Will Not Move In Reverse Or Drive
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 RepliesSanta FE SM (2001-06) :: Grumbling Noise When First Started And Put Into Drive Or Reverse
My 2003 Santa Fe makes a grumbling noise when first started, and put into drive or reverse. The noise seems to be coming from the passenger side of the engine compartment. The noise disappears when the drive train has warmed up.
View 4 RepliesSanta FE SM (2001-06) :: Rear End Clunking When Going From Reverse To Drive At Slow Speed
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 RepliesAccent LC (2000-05) :: 2004 - No Reverse / Shifts Hard Into Drive
2004 accent had a drink spill on lower console, and think this is why it quit shifting? Disassembled, cleaned switches, unhooked battery, and car still has no reverse, shifts HARD into drive, will not move further.
View 5 RepliesSanta FE SM (2001-06) :: Clunking Sound When Shift Into Drive Or Reverse - Bad Motor Mounts?
I have a 2002 santa fe 2.7. I just had the transmission rebuilt and since then have noticed a clunking sound when I shift into drive or reverse. It seems to be the lower motor mount is making noise from the motor moving the mount. I look at the mount and it appears to look good, but was wondering how I can really tell if a motor mount needs replacing or not.
View 3 RepliesGolf IV / Jetta IV :: 2005 - Jolts Forward When Shifting From Park To Drive And Occasionally From Reverse To Drive
Recently I've noticed that every time when shifting from park to drive and occasionally from reverse to drive in my 05 Golf GLS, I would have to remain off the gas for 3-4 seconds otherwise the car would jerk forward. If I press on the gas ever so slightly, the rpm would go up to around 1000 then jerk. Why this is happening?
View 2 RepliesElantra XD (2001-06) :: Manual Transmission - Thump When Shifting
I've been hearing a quiet 'thump' when shifting. In particular, when first letting up the clutch starting out in 1 but also when shifting between gears when the clutch is fully down such as from 2->3.
I thought perhaps a fluid change was in order since I'm at 110,000 miles. It didn't make any difference. (I used Mobil 1 GL5 which according to independent tests is safe on yellow metals.)
So then I wondered if it's the engine mounts, but I'm not sure what it sounds like when they need to be replaced or if simply shifting between gears while driving as described above would cause a worn one to 'thump'.
Ford F-150 (2004-2008) :: 2005 - Hard Time Moving From Park To Drive And Reverse
I have a 2005 Ford F-150 with a 4.6L and auto tranny non 4 wheel drive. I have a hard time moving from park to drive and reverse. Is there a switch that lets you put it in gear once the brake pedal is depressed? Could that have gone bad?
View 5 RepliesElantra XD (2001-06) :: Engine Light While Driving And 2nd Gear Taking Time Shifting - Thump On Transmission
O.K. first of all I had an issue with the Odometer pointer being jumpy. Sometimes it wouldn't move. Now I replaced the input sensor at first and did not fix the problem. I replaced the output sensor and fixed it. "BUT", Now, I have a problem with the transmission shifting. I get an engine light while driving and the 2nd gear seems to take its time shifting and when it does it make the left side drive shaft kick in hard and spends my wheel to a screeching effect. Plus a thump on the transmission. I rechecked the sensor for connection and reinstalled. Drove the car still have the same issue?
View 2 RepliesElantra XD (2001-06) :: Loud Thump When Go From Park To Reverse / Car Stuck In High Gear
What can I do about my car it's not shifting, it's stuck in high gear and when I go from park to reverse it makes a loud thump. The check engine light came on and the codes are transmission control module it's a 2006 and only has 30,000 miles on it. It's hard to believe it's the brain so we changed the fluid and cleaned the sylinoids but then when I drove it around the block I put it in reverse it didn't make the loud noise and it shifted fine for a minute before I got around the block and almost home it made a loud banging noise and went back to not shifting again. What the problem could be.
View 5 RepliesSanta FE SM (2001-06) :: 2004 - Clunking / Grinding When Shifting From R To D
Last summer my 04 SantaFe (140,000 mi, automatic) would feel like it was sticking and bumping when backing out of a parking space, then after shifting into Drive it would jerk and then make a huge thunking noise when applying the gas pedal. However, this would only happen sometimes, not all the time, and was not dependent upon the weather, surface, whether it had just been driven or not, etc. It would just happen when it happened. I brought it to the Hyundai garage and they replaced an axle and sensor. I continued having the same problem, brought it back to the garage and they replaced the viscous coupler.
I continued to experience the same problem after that, brought it back to the garage and they had the car for 10 days. I was told they had to get a mechanic in who was familiar working on 04 Santa Fe's and they determined the axle they replaced was bad, so they put in a new one. Everything ran great until I brought the car in early February for an "off balance ceiling fan" noise when accelerating. I brought the car to the Hyundai garage again and had the transfer case replaced.
Now the "clunking/grinding" is back when moving from R to D!!! So I brought it back to the garage again Monday and they said they cannot find anything wrong, and they are convinced it's just a symptom of the age and mileage of the car. However, it happened again today, but worse than ever before. This time it felt like it might not even move from R to D, and then it continued the grinding and bumping after accelerating and then the car felt "sluggish". I am convinced something is really wrong, although they assured me at the garage that the transmission is good, the axle, sensor and boot are all good etc. What else could it be?
Santa FE SM (2001-06) :: 2004 Sticky Shifting / Car Would Not Start
I'm working at summer camp with limited access to my mechanic and information on what i can do. I went to move my car today and when I put the car into reverse the shift was very stiff it went, and moved in reverse the same happened when putting it into drive. The vehicle drove fine the few feet i needed to go but then was sticky shifting into park. I thought I had it in gear all the way but i couldn't turn the vehicle off. I finally got it to turn off (I'm honestly not sure how) and so i tried to start it again to see if it was just a fluke thing... it wasn't. my car would not start. the radio a/c and basic lights came on but the engine did not. there was no clicking noises of anything. a friend and i tried opening up the hood to see if anything looked out of place of did something wrong when trying to start it but we didn't see anything.
View 1 RepliesSanta FE SM (2001-06) :: 2004 - RPM Fluctuations And Erratic Shifting
I have a 2004 Hyundai Santa Fe with a 2.7 4wd. It has started fluctuating the rpm's and is shifting erratically. I have seen on here that it is possibly the TPS. Does the same in manual or auto.
View 3 Replies