Santa FE SM (2001-06) :: Transmission Go Into Reverse Just Fine But Would Not Move In Any Forward Gears
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesFord Transmission :: 1994 F53 E4OD 460 CID Will Not Move In Drive Or Reverse
I been working on this unit and I running into this
no foward
no reverse
no foward in and gear at all
I have to check pump pressure
I'm changing fluid and filter
1994 F53 460 CID will not move in drive or reverse - iRV2 Forums
Subaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
Ford Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
Santa FE SM (2001-06) :: Transmission Won't Move Car / RPMs Went Up
The other day I was driving my Santa Fe. I noticed the RPMs went up and then the car started slowing down, so I pulled over. Since then the car won't drive. Engine starts up but the car won't move at all. When I push the gas pedal I hear the engine revving, but no movement in drive or reverse. No check engine light, and I checked the transmission fluid, looks and smells good. I checked and it has no transmission pressure. I verified by removing the transmission cooler lines and shifted the truck in all gears. Nada. Could it be the filter, a sensor or the torque converter? Or am I looking at having to replace the whole transmission?
View 21 RepliesSanta FE SM (2001-06) :: 2002 Auto - 4wheel Drive Doesn't Shift Into 5th Gear
Have an 02 Auto with the 2.7, 4wheel drive, and it doesn't shift into 5th gear. Can go through the 4 gears with the manual shift, but when just in drive, only shifts up to 4th. At 65mph, RPM's over 2500.
View 3 RepliesSanta FE SM (2001-06) :: Auto Transmission Seal Keeps Blowing
I have a 2002 santa fe v6 all AWD. It has already had a used trans installed about 3 years ago. Just the other day the front main seal in the trans starts pouring. I took it to a transmission guy it cost me about 600 to have one put in it, he said that was the the problem he got it fixed he drove it and it was all good. Get in it driving it home and everything goes fine. Then after about 5 or 6 miles the trans goes crazy, so I am wondering whats up. I get out and look and its out of fluid because the seal done blew back out. I call him he said he fixed it not his problem it worked when it left his shop.S o my question is what would make the seal need replaced again 5 miles down the road is it a torque converter problem, or something in the trans bad, or did the guy just not do it right. He told me to bring it back and he would look at it but I've done spent all i had on it for him to fix it.
View 2 RepliesSanta FE SM (2001-06) :: Auto Transmission Slipped Into Neutral
While driving the other day the automatic transmission in my 2003 Santa Fe slipped into neutral. I pushed the car home wherre it currently sits. I checked for error codes and found none. There is a grinding noise when I shift from any gear into park.
View 1 RepliesSanta FE SM (2001-06) :: Grumbling Noise When First Started And Put Into Drive Or Reverse
My 2003 Santa Fe makes a grumbling noise when first started, and put into drive or reverse. The noise seems to be coming from the passenger side of the engine compartment. The noise disappears when the drive train has warmed up.
View 4 RepliesSanta FE SM (2001-06) :: 2004 - Clunking Noise In Drive Or Reverse
2004 Santa Fe, clunking noise in drive or reverse. checked brakes and cv joints, replaced drivers front and still making the noise. Transfer case was a little low on fluid but not much. Put up on stands and turn wheels with no noise. Put in drive or reverse while in the air and rear wheels sit still. It is a 4wd so I would think that all 4 tires would be turning. While in the air the front both turn and no noise is made.
View 18 RepliesSanta FE SM (2001-06) :: 2004 - Hard Thump When Shifting From Reverse Into Drive
Recently my 2004 Santa Fe 2.7 AWD (~86k miles) has started to give a sort of hard thump when shifting from reverse into drive. It's fine going into any other gears and it shifts up and down normally. If I shift from reverse to neutral and then to drive it's fine.
I changed the transmission fluid when we first got the car at 40K miles with Hyundai Liquid Unobtanium SPiii fluid and again at 80k miles with Valvoline's SPiii offering. I just checked the transmission fluid level and it's within the normal range.
I can't tell if this is just drive-line slop or something else inside the tranny.
Santa FE SM (2001-06) :: Rear End Clunking When Going From Reverse To Drive At Slow Speed
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 RepliesSanta FE SM (2001-06) :: Clunking Sound When Shift Into Drive Or Reverse - Bad Motor Mounts?
I have a 2002 santa fe 2.7. I just had the transmission rebuilt and since then have noticed a clunking sound when I shift into drive or reverse. It seems to be the lower motor mount is making noise from the motor moving the mount. I look at the mount and it appears to look good, but was wondering how I can really tell if a motor mount needs replacing or not.
View 3 RepliesLS / MKZ :: 2002 Lincoln V8 Doesn't Move When Put Into Reverse Or Drive
My 2002 lincoln ls v8 140k miles doesn't move when put into reverse or drive 5 or even d4,3,2,1 , it just starts to roll back/forward when taken out of park. It has the gear selector with d5, d4,3,2,1 not the select shift. I was told needs new transmission, but before it stopped moving completely it was still driveable second slipped at lower speeds(mostly when looking for parking or in traffic).
I had made an appointment to bring my car to the shop and the same day is when it stopped moving. All this happen within a week during the week i constantly got an e where d5 was and on last day check engine light came on.
Lexus GS 2006-11 :: Brake Clicking When Move From Reverse To Drive?
I have a 2008 GS350. Been having brake clicking when I move from reverse to drive and lately been happening more when driving regularly. Brought it in to Lexus to get the complimentary 19-point inspection and they said I needed new brake pads and rotors. I did do a search and found it can be issues with front spindles, sway bar, bushings.
View 5 RepliesCamry :: 2002 - Grinding Noise And It Won't Move In Reverse Or Drive
I replaced the front hubs and bearings on my brothers 2002 Camry today. He drove less than a block and developed awful grinding noise and it won't move in reverse or drive. It rolls when I put it in park. I had to pull it back into my shop. Is it possible the inner CV came loose and i didn't realize it? It all seemed to go back together fine. The new CV axle nuts were quite tight and slow to put on with my impact gun.
What else could possible go kaput when I re & re hub/bearings? And what a long ugly job to replace those bearings. Don't even think about doing this without a good hydraulic press. Up to the point of getting knuckle off, it was easy job.
Golf IV / Jetta IV :: Post Oil Change - Car Will Not Move In Drive Or Reverse
I just changed my oil in my mk4 jetta 1.8L and after draining the oil, changing filer, and adding new oil, the car will not move in drive or reverse. Once I give it gas it will move but that's at the higher rpms. I am almost positive I didn't remove the transmission oil but I am just not sure.
View 12 RepliesSubaru - Outback - Transmissions :: Car Won't Move In Drive, Reverse Or Neutral
When I started my car and put it in reverse, it didn't move. It felt like my front, right wheel was in a divet or was being blocked somehow (intuitively it seemed like if I accelerated enough, it would eventually move, but since there was nothing physically stopping it - that I could see - I didn't want to break something by doing that). I tried putting it in drive and neutral and the same issue was still there. I put the car up on a jack and checked one wheel at a time - I could move each wheel completely around in both directions.
I could move the steering wheel all the way to the right and to the left. I tried turning off the 4-wheel drive and that didn't do anything. At this point I'm concerned it could be the transmission or the drive shaft, but I'm not sure what to look for in order to know if I need to get it towed to a shop (hoping I can avoid this) or if there's a simple test I can do, or a way to "reset" something if it may be locked. I haven't had anything happen to the car that would have been of concern.
Ford F-150 - 1997-2003 :: 1998 - Cannot Get It To Move In Drive Or Reverse
I have a 1998 f150 4x4, the truck has not been driven in a few years and it’s been outside in my driveway up on jack stands. I just rebuilt the front end and did a four wheel break job, after getting the truck off the jack stands, I can't get it to move in drive or reverse. I also noticed that when you go from reverse to park the gears grind and I can't even get it to shift into 4H. I checked the tranny fluid and it is fine, also the tranny was just rebuilt a few years before I stopped driving the truck.
View 6 Replies