Prius (Gen 2) :: 2005 Toyota - 12 Volt Battery Replaced Now Engine Idle At 1640 RPM
2005 Toyota Prius, 85,000 miles on the car. Recently changed spark plugs with stock NGK plugs. I replaced the 12 volt battery today because the old 12 volt battery was reading 9.6 volts with engine shut off. 13.8 volts with car powered up. Long story short.
Easy swap. I have lots of tools and I am a service technician in a Bridgestone/Firestone tire factory. I can work on most anything with no problems.
The car now idles at 1640 RPM as read on my scangaugeII. I have not plugged in my Auto Ingenuity program yet but there are no trouble codes that the scangauge can read. My airbag light is on but it was on before I changed the battery. My left Side airbag is unplugged or partially unplugged and I need to search for the plug. Any fix or some way for the car to relearn the proper idle? I also noticed that my Drivers side window Auto up and Auto down feature stopped working. I can read individual sensors with Auto Ingenuity if you need numbers.
The 12 volt battery now reads 12.6 volts with the car powered down.
Camry :: AC Compressor Not Working After Toyota Replaced Engine On 2008 Car
2 weeks ago my Camry 2008 failed the oil consumption test, so toyota fixed the engine. Few days after I got my car, I turned on the A/C but I was surprised that the compressor wont work. Totally dead.
I took the car to toyota and they check it out, they said they dont know whats wrong with compressor and I need to replace it for 1200$!!! IT WAS NOT A FREON PROBLEM, They claim that electricity is being delivered to the compressor but its just not working.
Is it possible that they messed up my compressor while fixing the engine? Also, I really don't want to fix it for that much, any thoughts where to fix it cheaper?
Elantra XD (2001-06) :: 2005 - Clutch And Pressure Plate Are Replaced Three Times Before 30,000 Miles
In less than 30,000 miles, I've replace the clutch, throw out bearing, and pressure plate three times. Dealer adjuster clutch at 12,500. First replacement at 15,000 miles. I do not ride the clutch
View 8 RepliesCherokee :: 98 ZJ 5.2L - Humming Noise After Replaced All Front End Steering Parts
My '98 ZJ 5.2L. I just replaced pretty much all of the front end steering parts because there was a lot of play going on and most of the boots didn't seem to hold grease. I replaced my tie rod ends, center link, drag link, and steering stabilizer. I did my best to align the tires using a tape measurer and ended up within 1/8 inch difference. I couldn't get it any closer than that, so I left it. Now, my Jeep is humming whenever I turn the wheel. Normally, I might look to either the power steering pump or some of the front end parts, but seeing as I just replaced pretty much all of them and I replaced my power steering pump last winter.
View 1 RepliesFord F-150 (2004-2008) :: Replaced Many Parts / Rebuilt Engine But Got Codes P0345 / P0022 Again?
I'm having the well known situation with P0345, P0022
Replaced both phasers, replaced cam sensor, checked timing (properly aligned), assembled back still running rough and rattling, used 10w40 oil,
Complete rebuilt engine, we did head work new seals and springs, valves are straight I had it checked out twice for assurance. New pistons, new rings, new bearings, new oil pump and seals of course. If I disconnect cam sensor Bank 2 it works fine but still runs a little rough.
- Replaced one tensioner due to gasket wear.
- I was told to check on alternator ground (it's missing I know cause it got broken and I haven't replaced that ground that goes into the engine.)
- I also was told change oil to 5w20 and filter (Not FRAM), add some lucas and it should be the fix.
- Also told to disconnect the oil pressure sensor and it would fix the problem but it will throw a code for that.
- I haven't replaced the timing chains I feel they're a little loose but they haven't jumped the teeth, so I guess they're good.
- I saw in one thread to move a teeth on phaser giving me code bank 2 (moved one teeth back and then one teeth forward but it didn't work)
When I first rebuilt the engine I was having the rough iddle then I scanned it and it gave me the cam positioning sensor code P0345, then after I replaced it problem got fixed and code was gone, I was using the truck for 2 days with no issues, then the problem cam back with the two codes P0345 and P0022!
Honda - Accord - Clutches :: 2003 - Clutch Master Cylinder Changed Six Times In 12 Months?
I have changed the clutch master cylinder on my '03 Honda Accord (6 cyl.) six times in the past 12 months. Either the o ring seal blows out or the bolts holding the plate down breaks off. I bleed the clutch of bubbles until the oil runs through also. What am I doing wrong?, I'm about to send this car packing.
View 9 RepliesPrius (Gen 3) :: 2009 - 12V Battery Keeps Dying / Replaced 3 Times
Bought a 2010 Prius V new and have put 100K on it since Sept. 2009. About 9 months ago, the 12v battery died. I ordered a Yellow Top replacement from Amazon, charged and installed it. Six weeks later, the new battery's died. I charged it again and suspected the engine's wasn't charging the battery. I took it to Toyota for an electrical checkup and they say all is fine. Six weeks later, the battery's dead again.
This time, the charger says it has a dead cell and won't take a charge. Amazon replaces the battery for free. The cycle repeats three more times and again, dead cell. This time I go to Toyota and buy their expensive battery. The cycle continued four more times (although I haven't had a dead cell indication). I've been back to Toyota for follow-up twice and each time they say there's nothing wrong with the car. The last time they told me we weren't driving it enough to charge the battery but I know that's because we take several 150 miles trips every other week or so (plus daily commuting time).
I'm thinking there's something that's causing a slow drain and wondering if it could be the digital system that keeps your inside lights on after you exit the vehicle and then slowly dims them, only it's not going completely off due to age.
Prius (2004-09) :: A/C Compressor Replaced Now Loss Of Power And Bad Smell?
Had A/C go out while in Vegas almost 2 weeks ago. Dealer said compressor dead, replaced at my dealer back home, now having loss of power issue's, poor acceleration, 29mpg, & bad smell like transmission fluid or catalytic converter... Problems noticed after picked up car, then went away, now back.. No codes on the scantool, no lights etc.
View 6 RepliesPrius (2010-12) :: Clunking Noise When Turning The Steering Wheel - Replaced Intermediate Shaft 3 Times?
Our 2012 Prius with now 17,000 miles in 8 months has developed a clunking noise when turning the steering wheel, especially far to the right at low speeds.
The first time the dealer identified it as a failed intermediate shaft and replaced it under warranty. Shortly after we told them it was starting to make the noise again, but they claimed they couldn't replicate the sound and anything they heard was normal 'linkage' (whatever that is). Shortly thereafter the clunking progressed so we took it in for now the third time, and they confirmed the problem, spoke with Toyota who said we must have had a bad part, and replaced it again.
Toyota - Venza :: 2009 - Brakes Causing Vibrations In Few Months?
I have a 2009 Toyota Venza V6 AWD with 60,000 miles. A few months ago I had the front rotors and pads replaced by Sullivan Tire and Auto in Massachusetts. Since that time, the brakes have started causing a grinding or vibration. It ONLY occurs at very low speeds, especially in stop-and-go traffic on the highway and only after the car has warmed up with perhaps 20-30 minutes of driving with braking. You can feel it in the steering wheel and even in the seats. Sullivan has been AWESOME in trying to solve it, already replacing the rotors and pads once and having taken them apart two other times. They seem stumped and I can't find anything related on the internet. Several techs have taken it for a ride both with and without me and every one of them confirms the same strange grind/vibration/rub and under only the conditions noted above.
View 5 RepliesPrius (2004-09) :: 2005 - How To Install A/C Compressor
My wife and I have had a 2005 Prius for a little over a year now. When we bought it, the previous owner said the A/C system was new. Once the spring/summer hit, we realised that wasn't true- apparently the blower motor was replaced, but the compressor was bad (dealer confirmed). We just lived with it last summer, but I am wanting to replace it now before it warms up.
I am home mechanic- no professional, but I have done everything from engine rebuilds to engine swaps at my house before. There are very few jobs that my cars have needed that I haven't done myself. The Prius is one thing I haven't done much to, and am not completely familiar with. I looked at a diagram, and the compressor seems easy to access from below the car. I have ordered a service manual for the Prius, and will use that.
Toyota - Prius :: Low Oil Pressure Red Message Flashed 3 Times In Last 5 Miles Of 10 Mile Trip (45 - 50 Mph)
The oil was changed by a highly reputable shop 2 days ago, (45 miles ago). My wife noticed today that the "Low Oil Pressure" red message flashed 3 times in the last 5 miles of her 10 mile trip (45-50 mph). She stopped the car and called me. I arrived at the parked Prius and saw no oil on the dipstick. I poured a quart of synthetic in and looked under the car to see it pouring out. My finger discovered that there was No Oil Plug. I called the shop and they sent a tow truck, put a new oil plug in, refilled the oil and claim no damage since "the Prius shuts off the gas engine when low oil pressure is sensed". Looking for information about this "shut off feature?" What should I ask from the shop? What should be tested & checked for? How do you test for damage to the bearings? How about a compression test? The car has 100K miles.
View 19 RepliesPrius (2004-09) :: 2005 - AC Malfunction / Possible Blockage Or Really The Compressor?
It's one of those days again when the temps are starting to get hot here in Austin, Tx. My AC started acting up during the Spring and first started working fine then after about 10-15 minutes of driving the air starts to blow warmer. The air doesn't go back to cold unless the car has been parked and off for several hours or overnight, and even after that it only blows cold for 10-15 mins again.
Well, I didn't have the time/money to mess with it. The recent May it stopped cooling completely. I recently took it to a local shop and we look at it together. Drained the system and the mechanic was saying it's pulling some air and a little refrigerant. Well, we recharged the system and we could only put in 0.5 lbs and the Low side just maxes out. The system is supposed to hold 1.06 lbs so we were left scratching our heads.
Decided to check for leaks, discharged the system again and hooked up a vacuum pump and see if the gauges will go below 0 for negative pressure and they never did. So the shop doesn't think my system has a leak. They could have used a dye to check but didn't have any on the shelf at that moment.
I also have a DTC code of B1476 and we followed the shop manual. Fans blow into the engine and sometimes we had the bubble but couldn't add more refrigerant due to the Low side being maxed.
My father thinks I most likely have a blockage somewhere in the system. If so, how I can check for this? Is there a specific place or two I can look to find out the system is blocked?
Some people on the form seem to have AC problems, including some with the B1476, and others that couldn't find the problem very well. I'm worried that replacing the compressor wouldn't solve the problem, especially if there is a blockage or something. I usually do a lot of mechanic work but I've never actually worked on an AC system before. I would love to dive into this, even if I can only do part of it and then send it to the Toyota dealer for a flush and charge.
Prius (2004-09) :: 2005 - AC Won't Working When Stopped For Short While / Replace Compressor?
I have an issue with the air conditioner of my prius. It just works while I am driving, but it does not work when I stop for a short while, such as waiting for signal. The fan is working fine. I visited a dealer and they told me the gas is leaking... but, they are wrong. I cannot believe them. The gas is fine and there is no leak and no problem exists at any other parts. Need to know about it? Should I replace the compressor?
View 3 RepliesCamry :: Batteries Replaced Several Times, Keeps Failing
My wife drives a 2005 Solara 4 cylinder 2AZ-FE. Over the past few years, it has been going through batteries about every year and a half. The batteries have all failed on the load test.
So far, I've removed the alternator and taken it in to get it bench tested, tested fine. I had the full charging system check with the machine, starter tested fine, alternator volts were fine, only problem was the CCA load test (for which the battery was replaced under warranty). I tested for parasitic battery drain several times, got some drain for awhile after car is powered off, but it eventually falls to zero. I checked for voltage drop across the wiring, visually inspected the wiring to the starter, alternator, etc. and made sure the ground connections were tight from the battery to the frame and engine. Everything looked good.
The only thing I can come up with is that the most recent battery boiled over a bit at one point in time because there was evidence of acid spillage. Also, once (and only once), my wife noticed her lights flickering while her car was idling for awhile during a cold morning. These two things lead me to think it must be the alternator (voltage regulator), but neither the bench test nor anytime I test it at home reveals any issue.
Maybe it's an intermittent problem from vibration, etc. I just hate to plunk down the cash for a new alternator if that isn't the issue.
Prius Plug-in 2012-15 :: Identifying Bumper Parts For Replacement?
Yesterday I came home for 20 minute stop. I parked with my front end sticking out of the garage.. Big Mistake! My 10 year old daughter sees the garage open and hits the button to close the garage door and walks away. Worst part is! I could hear the door closing from inside the house and could not get outside fast enough!
I've spent the last 24hrs trying to find replacement parts on the net and all I have obtained is more confusion. Is it all one assembly or am I looking for multiple part numbers??
Passat (B5) :: Brakes And Rotors Replaced At Least Four Times In Three Years
My 2004 Passat is less than three years old and the front and back brakes & rotors have been replaced at least four times.
View 8 RepliesPontiac - Sunfire :: Replaced Timing Chain 3 Times?
I had to replace the chain tensionor 3 times. I would like to know if that is a common problem with the 2.2L engines. How the chain is oiled while in operation.
View 4 RepliesFord F-150 (2004-2008) :: AC Does Not Blow Cold At Times / Compressor Not Coming On
I have a 2007 F150 with a 5.4. I am having an issue with my A/C and more.
Here are the symptoms:
1) A/C doesn't blow cold, at times.
2) Compressor not coming on, according to mechanic.
3) Engine sounds like a freight train, at times. Like on a super cold day and it has to work hard.
4) Very poor fuel mileage since this started.
I took it to a shop, and they said it was the engine cooling fan that would not come on. So I replaced it. Same issue. I then took it back and was told there is a wiring problem. After 3 days they couldn't find it. I needed my truck back and dropped it off again. Then they said it was the A/C compressor, maybe. They wanted to try it and then see what happened. I told them no way.
Temperature, according to the gauge is good. Noise comes and goes. Not dependent on anything. Weather, temperature, car heated up or dead cold. Just comes and goes.