Ford F-150 (2004-2008) :: 2005 - Got Codes P0022 And P0345?
So I have an 05 Expedition (I know this is the F-150 forum, but more visibility) that is throwing a P0022 and P0345. I get these point to the cam phasers, so before I throw $450 on a phaser kit and oil pump, I want to make sure its a good fix.
I have done a lot of research on this forum and other where people have replaced their phasers and it doesn't end up fixing the issue. So I just was looking to get some tips before I endup shot gunning parts.
Ford F-150 (2004-2008) :: 2007 - Throwing Codes P0012 / P0022 And P0345
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 RepliesFord F-150 (2004-2008) :: Got Codes P0174 / P0171 / P0345 And P0349?
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 RepliesFord F-150 (2004-2008) :: Misfiring - Rough Idle - Got Codes P0340 / P0344 / P0345 And P0349?
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: Headers And Exhaust Replaced - Codes P0010 And P0020
I replaced my headers and added slp loud mouth 2 side exit now my truck is throwing every evap code o2 codes and p0010 & p0020, There is 17 codes total. The headers are obx without cats. Also added 80mm bbk throttle body and some brisk racing plugs with hot street coil packs. Truck run with all of that stuff fine but when i did the headers and cat back everything went wrong.
View 9 RepliesSanta Fe (CM - 2007-12) :: Check Engine Light Went On - Error Codes P0021 And P0022
2 error codes? Car runs fine - nothing seems wrong - the check engine light went on, so I pulled out the scanner which came up with the 2 codes: P0021 and P0022.
View 8 RepliesFord F-150 (2004-2008) :: 2006 - Code P0345 - Low Oil Pressure
I have been having quite a rough time fixing a P0345 code on my 06 F-150 w/5.4 w/85,000. This truck has gone to a Ford dealer every 5K for the oil change/checkup etc.
Long and short - P0345 Code @ approx 83,500 miles, rough idle once the engine was up to temp and it would clear if you bumped the skinny pedal.
I have replaced the following:
--Both Cam Phasers
--Both VCT Solenoids (they both had holes in the screens - see this post [URL] ....
--Passenger side Cam Position sensor (I broke it pulling it out to do phaser swap)
--Spark plugs - SP515's
Issue was still present so then I replaced:
--Complete Timing chain set (Chains,Gear, Guides and Tensioners) - Drivers (left) side tensioner collapsed.
Once all back together and running the code is still there so I finally installed a REAL electric oil pressure gauge. Turns out I only have about 15psi at hot idle and 50psi when driving etc.
I am at wits end, because at this point I would have to guess that the engine is junk... Either a bearing is shot or whatever... Do I take the 3-4 hours to drop the pan to potentially see what is going on? Or just drop some 15W40 in the engine and trade it in?
Chevrolet - Tracker :: 2003 - Noisy Engine After Rebuilt - Replaced 3 Times?
2003 Chevy Tracker 4 cylinder. Engine rebuilt and cannot get lifters to quiet down. Replaced 3 times. Bent valves on first install.
View 3 RepliesFord F-150 (2004-2008) :: Slight Ticking Noise - Code P0022
Getting code P0022, which is over retarded cam position, drivers side bank. My 2004 F150 has the 5.8 triton. I have replaced all cam phasers and tensioner a as well as the timing chains. I have also replaced both VCT solenoids. Before I was getting codes for both banks, now just the code mentioned above with a slight ticking as well. My question is this... What am I not seeing? What could be causing this?? Would it be beneficial t get the lockout kit for the phasers to always keep them open?? Seems to stall a little at very low RPM like when you are off-road.
View 1 RepliesFord F-150 (2004-2008) :: Knocking Noise / Running Rough And Stalling - P0340 And P0345
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 RepliesFord F-150 (2004-2008) :: Running Rough Loud And Dies - P0022 Cam Sensor Code
My wife's 06 expedition 5.43v runs rough loud and dies. Not all the time just when it's to hot. I got a code it's p0022 cam sensor. I changed both started the rig up and heard loud rattling like metal maybe chain. It lasted for a the length of my video 1.4mins give or take then went fine, i turned the car off and back on everything seems fine. I know I got her oil done after driving. She had metal/plastic in her oil. I had all plugs done and actually i re did the 8th cylinder plug because it was miss firing and i pulled it by hand with only the socket no ratchet. I'm thinking the chain is going bad if not already bad. Only 113k miles my 04 f150 5.43v lasted 250k before motor swap...
View 7 RepliesFord F-150 (2004-2008) :: Code P0022 - Intake Camshaft Position Timing-over-retarded Bank 2
Driving around today my cel flashed on. Checked my programmer its saying P0022 intake camshaft position timing-over-retarded bank 2. What is the culprit?
View 2 RepliesFord F-150 (2004-2008) :: 2005 - Rough Idle At Low Speeds Primarily In Reverse / Code P0022
2005 f150 Lariat 4x4 5.4
Had phasers, tensioners, chains, guides, and sensors replaced. After driving the truck, it started to get a rough idle at low speeds, primarily in reverse. Changed both vct solenoids with no results. Started to get p0022 code. Changed the oil with motorcraft filter and 5w-20 twice after the work had been done, thinking it might need it. Vct's were a little varnished, but not too bad.
After a couple days of light driving, got a misfire on #3. Replaced the coil and it hasn't been back since. I am stumped at this point.
The computer show the timing to be at +13 when sitting stopped and in drive. It fluctuates a little, but not much. When the truck goes into a rough idle. The rpm's fluctuate wildly. It seems to be happening more frequently, the more I drive it.
Ford F-150 (2004-2008) :: Just Rebuilt Trans Now No Speedo / Truck Goes Into Limp Mode
Just fully rebuilt transmissin 4r75 replaced all planet gears clutches etc. Now with it all back together the speedo does not work on truck goes into limp mode. I replaced the vss sensor an no luck
View 8 RepliesFord Super Duty (1999-2016) :: 2006 F250 5.4L With Codes P0426 And P0345
Where to start. Have had to replace a few COP's in the past and replaced all spark plugs 20k ago. Truck runs rough at idle and sometimes stalls when changing gear. Strong exhaust smell when sitting idle. If I put my foot in it there is hesitation. Engine seems to smooth out quite a bit but also seems like it's getting more power in stages. Codes P0426 and P0345 ....
View 2 RepliesFord - Taurus :: Transmission Rebuilt / CEL On And Multiple Codes Came Up
I have a 2005 Ford Taurus. We had an $1800 rebuilt transmission put in 8 months ago and it's already giving us problems! The engine light has also been on. We took it to autozone and multiple codes came up. We've already put way too much money into this piece of shit and I don't want to get screwed by another mechanic! Where do we go from here? Is there anything we can fix ourselves? The codes are p0300, p0301, p0305, p0316....
View 11 RepliesFord F-150 (2009-2014) :: Codes P0345 And P0349 - Camshaft Position Sensor Bank 2 Circulation Error / Interim
For 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
Cherokee :: 98 ZJ 5.2L - Humming Noise After Replaced All Front End Steering Parts
My '98 ZJ 5.2L. I just replaced pretty much all of the front end steering parts because there was a lot of play going on and most of the boots didn't seem to hold grease. I replaced my tie rod ends, center link, drag link, and steering stabilizer. I did my best to align the tires using a tape measurer and ended up within 1/8 inch difference. I couldn't get it any closer than that, so I left it. Now, my Jeep is humming whenever I turn the wheel. Normally, I might look to either the power steering pump or some of the front end parts, but seeing as I just replaced pretty much all of them and I replaced my power steering pump last winter.
View 1 Replies