Santa FE SM (2001-06) :: Transmission Won't Move Car / RPMs Went Up
The other day I was driving my Santa Fe. I noticed the RPMs went up and then the car started slowing down, so I pulled over. Since then the car won't drive. Engine starts up but the car won't move at all. When I push the gas pedal I hear the engine revving, but no movement in drive or reverse. No check engine light, and I checked the transmission fluid, looks and smells good. I checked and it has no transmission pressure. I verified by removing the transmission cooler lines and shifted the truck in all gears. Nada. Could it be the filter, a sensor or the torque converter? Or am I looking at having to replace the whole transmission?
View 21 RepliesSanta FE SM (2001-06) :: Engine Will Keep Running And Car Won't Move
I have a 2002 Santa Fe V6. I'm getting the codes p1529, p0755, p0760, & p0765.
The car can start up & go, only for a short time. Engine will keep running, car won't move.
Kill the engine for 3 to 5 minutes, can start it up & go once again. Going 40mph increases the odds of the car not moving quicker.
Elantra XD (2001-06) :: Stalling When Try To Move The Car Or Step On The Throttle
I can get it started and let it idle for an hour....idles smoothe. As soon as I try to move the car or step on the throttle...it stalls.
View 2 RepliesElantra XD (2001-06) :: GLS Clutch Engaged And In Gear But Car Will Not Move
Here's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
Santa FE SM (2001-06) :: 2003 - Won't Move And Front Right Smoking
I have a 2003 Santa Fe and it's been running fine except I just replaced my oil pan from damage from ice and just did front brake pads 2 days ago.( oil went onto the pads and caused a weird grinding sound) ...
After the brake pads were done it drove fine. I came home and the next morning I go to reverse and the truck will not move at all. I can go to any gear but it just will not move. I thought it could be the brakes were frozen because the front right was smoking after the pads were installed and had the guy who did them check it out. he figured it was a caliper on the driver's side and replaced it, but it will still not move. I am praying this is not a trans problem.
Santa FE SM (2001-06) :: Auto Transmission Will Not Move In Reverse Or Drive
I just did a motor swap on a 2003 with 3.5 auto tranny and awd. engine runs great and every thing is running fine. Only problem is that the trans will not create any power. With no drive shafts on it still wont move the splines. With that said the trans was driving/running great b4 the swap.
View 2 RepliesMazda - 626 :: 2001 - Running Rough / Huge Jerk When Move From 1st To Second
Our 2001 mazda 626 has begun to run rough(shaking the car) when idling at a stop sign or stop light and once that begins when we push on the gas to move from 1st to second there is a huge jerk. If the air conditioning is on it is worse. It is an automatic.
View 3 RepliesInfiniti :: 2001 - Losing Power / Car Will Not Move Forward When Push On Gas
I have a 2001 infiniti i30 automatic with about 118000 miles. The car runs and drives fine but every now and then while i am driving it and i push on gas the RPM will go up but the car will not move forward. I noticed that this usually happens when I drive the car a lot. If i turn it off and on it drives normal again. I have had 3 mechanics try to troubleshoot it one recommended to change the MAF which I did and the car ran fine for about 6 months and is starting to do it again. Service engine soon light is on again. What exactly is the issue that's causing it.
View 2 RepliesLumina :: 1993 - While Turning Makes Grinding Clattering Noise - Won't Move Forward But Will Move In Reverse
I'm new here and I am having issues with my Lumina. It is a 93 Chevy Lumina Euro 3.1L 6 cylinder and has 192K miles on it. It has had one owner for the past ten years that I know for a fact.
Here's what happened. I was coming back home (2hr trip) The brakes had started making that roaring sound on the way down and had gotten worse when I got ready to make the trip home. Okay so I know the brake pads needed to be changed. No big deal. Well going down the road at 65mph I round a curve and my car starts making this REALLY LOUD grinding clattering noise. It took me forever to get it stopped. I will still in the road and I needed to get it out bc it was right around a curve. So I put it in drive and it wont move. So I put it in reverse and it moves just fine with no problems and no noises made. After backing it out of the road I tried to put it in drive. It moved forward a few inches and stopped like something was binding it up.
So here's the problem.. it will move in reverse with no problems at all and only creeps a couple of inches forward then stops. The harder you press on the gas the more it tries to lurch forward but will not move.. like it's caught on something.
We changed the rear brakes on it. Discovered that the driver side rear rotor and caliper were broke beyond repair so we replaced those too. Still the same.. moves forward a lil bit and stops but will go in reverse just fine. We don't seem to think its the tranny bc it pulls hard and seems to not have any problems pulling.. but its like something is bound up somewhere. That is the best way I know how to explain this situation.
Chevrolet - Blazer :: Barely Move Forward And Will Not Move In Reverse
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesSanta FE SM (2001-06) :: Transmission Go Into Reverse Just Fine But Would Not Move In Any Forward Gears
I recently bought a 2001 Sante Fe 4X4, (my first Hyundai), that has transmission issues. It has about 135,000 miles on it. It will start easily, and go into Reverse just fine, but would not move in any forward gears. It would occasionally shudder a bit when put in 'drive', but only move forward a few inches. Recently, my mechanic backed it around, then decided to try it in forward again. This time it went forward a couple hundred feet, then quit moving forward. Do I need a new transmission, and if so, what vehicles use this same transmission? Or is there a sensor or valve that could be defective?
View 5 RepliesSanta FE SM (2001-06) :: Gear Shifter Very Hard To Move And Doesn't Really Go In Park?
This morning as I get in to drive my kid to school (2005 2.7 2 wd auto) as I go to put it in reverse I noticeably have to pull it with some force. I have never had to "force it" before, it had always switched gears with ease. This time it felt very stiff but had no issues going into gear. After I dropped my son off at school I went through the gears up and down and it felt very stiff (at this point i have no issues with starting it or P).
At lunch I go out to get something to eat and when I go to start it up it won't start. I try and try and nothing. All the lights came on, it's not a battery issue at all (brand new). But after 10 tries it starts, so I'm pretty happy. Then I go to put it in gear (reverse) I can not press in the button on the side of the gear shift. It will not go in. I press with all my might and it wont budge. But again, after about 10 good tries at it goes in and I can then select my gear but still feels very stiff.
After stopping again I didn't shut off the engine and dicked around with the shifter basically figured out that my car is not recognizing Park. On the instrument panel each gear lights up but not P. It gets very stiff when trying to put it in P but it doesn't actually go into P. If I put it in P (or really the further up it will go) and shut off the car, it won't start again. I can start it up in N and only N.
Monte Carlo :: 2001 SS Hardly Move When Shifted Into Drive Like It Was Starting Out In High Gear
Recently purchased this Monte Carlo SS with a bad engine. Picked up a really good engine and it sounds great. Backed the car out of the garage, and when I shifted into drive, the car would hardly move. It felt like it was starting out in high gear. Had code P1860 (Trans converter clutch) set. Car has 150K on it. Suspected bad trans. Just had the trans rebuilt by AAMCO to the tune of $1100.00. Still have the exact same problem. The car will go in reverse just fine, but it won't hardly move forward. The old engine pushed a lot of antifreeze and oil through the exhaust. When I started the new engine, it smoked like a smoke stack for about 20 minutes, but then quit smoking. What am I missing? The trans is full of oil, and all connections are fine.
The Monte Carlo is a 2000, not a 2001.
Elantra XD (2001-06) :: Entire Car Electrical System Dies When Move The Key To Start Position
I am experiencing a new problem with my 2006 Hyundai Elantra. For the 2nd time now (meaning this morning) the car will not start the first time in the morning. As I turn the key past the "on" position all the regular lights will come on, bells ding, etc. but when I move the key to the "Start" position, where the car would normally crank over and start, the entire car electrical system dies. (Interior lights off, non-responsive with the keyless entry, etc.) Yesterday, I figured my battery cables might be loose or something like that. By the time I popped the hood (no more than 30-45 sec) everything turned back on. I then tried to start the car again and the car started normally without issues, with me having done nothing other than pop the hood by this time.
When my car sits all day at work and I return to leave it will start normally without problems. This morning is now the 2nd time this has happened. My battery is practically brand new as it was replaced about three weeks ago. So, my question is: What could be causing the car to not start in the morning the first time, but then somehow "fix" itself without any user intervention on my part other than popping the hood?
Subaru - Impreza :: 2001 - Hard To Get Into Gear And It Would Not Move In Reverse / Neutral Or Drive
I had a problem with the CV Axle and the Wheel Bearings. I replaced them already and I ran into another issue with the Wheel Studs and the Ball Joint, so I ended up replacing them as well. Yesterday I put everything back together after replacing all the parts mentioned before and I made sure everything was bolted down and tightened, and then the tire back on and lowered the jack. I started up my car expecting it to drive just fine and it was harder to get into gear than before and it wouldn't move in reverse, neutral, or drive. I called a Monroe Muffler around here and they told me that the CV Joint is probably not seated all the way inside the Transfer Case.
So later the same day I took everything back apart and made sure that I put the CV Joint back into the Transfer Case and I put the pin back in and made sure that both CV Axles would turn at the same time, which they did. I figured it was good so I put it all back together again and went through the same process as before, making sure everything was tightened down, all the bolts and nuts and pins were where they needed to be. Everything seemed to be good. I put the tire back on again, lowered the jack, started the car and attempted to drive it again. It still won't move. Why this is happening.
Mazda - Miata :: 2001 - AC Blow Cold For About 30 Minutes And Temp Gauge Move Towards H
I have a 2001 Miata. It's been over 100 degrees daily lately. The AC will blow sort of cold for about 30 minutes and the temp gauge will move towards the H hashmarks. If I turn the AC off, the gauge will slowly drop. I've also noticed that the amount of cold air is decreasing as time passes. In fact, the other day, the system was blowing air hotter than the outside temperature after about an hour drive.
The viewing glass has bubbling stuff flowing thru it. The recently flushed radiator is full as is the overflow reservoir.
Ford Ranger / B-Series :: 2001 - Copper Cable Doesn't Move When The Shifter Does
After taking apart my instrument panel to change the bulbs, I went to reconnect everything, but now the gear shift indicator isn't working. I can change gears fine, and everything else on the instrument panel works just fine.
The copper cable that connects to the shifter doesn't move when the shifter does. Is there a way to fix this problem, or do I need to find a replacement cable?
Ford Escape / Hybrid :: 2001 - Cannot Move Shifter Out Of Park / Safety Interlock
While traveling I made a fuel stop. Restarted engine fine, stepped on brake, but could not move the shifter out of Park. Towed to Ford dealer, after extensive trouble shooting replaced shifter cable and transmission position sensor. A week later same problem but glad I learned about the interlock override lever on the steering column so can continue to drive. It locks up several time a day. Here's what I know and observe.
. brake light switch appears to be normal
. engine starts normally
. brake lights operate normally
. fuse on interlock function is ok
. when the lockup happens the shift indicator is missing the box over the P
. this may not relate but backup/reverse lights operate very weird - in reverse they only light when the engine in rev'd and go out when the gas pedal is released
There appears to be a gremlin in this Escape that eludes Ford and me. I read some reference to a computer control involved in the interlock function. I'm at a loss.
Lincoln - Towncar :: 2001 - Intermittent Vibration When Move The Gear Shift Lever To D For Drive
I have a 2001 Lincoln Town Car that has an intermittent vibration that can be felt when seating in the car and you move the gear shift lever to D for drive. The car has 141,000 miles. It is an automatic transmission. The vibration cannot be felt when touching the steering wheel. What could be causing the vibration?
View 3 Replies