Accent LC (2000-05) :: 2002 - Code P0106 / Map Sensor Code
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
Passat (B7) :: 2012 - CEL With P0106 And P0106 PD Codes?
I am having a problem right now with the check engine light on and P0106 and P0106 PD codes scanned. I bought this 2012 Volkswagen Passat 2.5 S from Hertz Car Sales for less than a month.
When I drove the car back from work on a Tuesday night, January 13, my car was doing fine at first and was suddenly reducing power with check engine light coming out. It was highly congested with massive traffic and cars on the 101 freeway towards Downtown.
I was luckily and safely able to drive the car back to my house. I could not take it to anywhere since it was already 7:30 at night. I decided to let the car sit for a few days until the weekend comes.
However, when I decided to take the car to an auto shop today, the car would not crank and start. Now, I have both check engine light and EPC+Battery light.
Passat (B7) :: 2012, 2.5l - Diagnosed CEL With P0106 Code
Had CEL light come on with the code P0106 barometric pressure sensor.
View 2 RepliesSonata I45 (YF - 2011+) :: CEL Came On - DTC P0106 For Map Sensor
Installed hid and relay kit yesterday...after reconnecting the battery the check engine light came on the dtc that was pulled was p0106 for the MAP sensor... i had it cleared and it keeps coming back... The car still runs fine just seems as if it idling low...
View 8 RepliesJetta - Volkswagen :: Check Engine Code P0106 / Clean Throttle Valve
VW Jetta SE 2.5L... Took my car to the dealer for a check engine light, the code came back P0106 which states I need my throttle valve cleaned and the dealer also said I need my brake vacuum pump replaced.. Do these go hand in hand? How should I proceed with the dealer? I have only 60,000 miles on my vehicle was there a recall on this issue? The dealer already updated the software in the technical bulletin.
View 2 RepliesSonata NF (2006-10) :: Throttle Body Cleaning Due To Rough Idle Occasionally / Code P0106
Trying to clean the throttle body on my 09 sonata 2.4L due to rough idle occasionally (throwing P0106, replaced MAF sensor still same problem), one quick question, is it okay to force the valve open (with connector disconnected of course), and is "re-learning" necessary and what's the proper way to do it?
View 2 RepliesSonata I45 (YF - 2011+) :: 2011 - Engine Code P0106
I just replaced my OEM battery with a duralast from autozone. The battery had 138,000 miles. Shortly after, the check engine light came on and code says P0106. Map Sensor. Seems like to much of coincidence that this happened. Have read that disconnecting battery cables for 3 hours may do the trick.
View 8 RepliesPassat (B5) :: P0322 Crankshaft Sensor Code Detected
My car is an AUG 1.8t with 153K miles and it has been running great since the timing belt change last summer. It died while driving it earlier today. I pulled a P0322 code which looks like it's for a crankshaft position sensor. I cleared the code.
After the car sat for about an hour I was able to restart the car and drive the car two miles back to my house. On the way back I felt the engine shudder and got an Engine Workshop warning, no CEL. I scanned anyway and found a pending P0322. Once I shut the car off it cranks but will not start.
Passat (B5) :: CEL Code P1296 - Coolant Temp Sensor?
I was driving today when the CEL came on, I scanned the car which gave me 1 code: P1296.
I googled it and said it is possibly the coolant temp sensor?
The Engine temp was normal at 190' or just below even after quite a bit of driving today.
Would the problem just be the sensor or should I be looking for other problems as well?
The car is a 2002 B5.5 AWM 1.8T Tiptronic.
Passat (B5) :: 2002 - Cat Warm Up Threshold Low Code / O2 Sensor
I have a 2002 GLX Wagon 2.8 30v, and was getting Cat warm up threshold low code, on the driver side due to the cat being bad. As a temp fix I decided to use spark plug haulers to gap the sensor. When I removed the O2 sensor I wiped the dirt off with a paper towel, which was clean and dry. I put the sensor back on, but now I am getting 4 codes which won't go away. p0036 p0056 p0141 p0161. These are O2 heater circuit codes both bank 1 and 2. I did not touch bank 2 so I don't know how I could have caused this error. I tried to take off bank 2 sensor but it is really stuck on there.
View 3 RepliesPassat (B5) :: 2002 / 1.8T - Knock Sensor Code 16711 (P0327)
So a letter history about the car and this car is a friends car. They owned the car and drove without changing the timing belt when the car hit 109k. So the timing belt snapped and they went out and bought a timing belt and also the timing belt kit with the pulleys and all. They installed it.. didnt turn over or what so ever.
They towed the car to us which we own an auto repair shop. We knew the valves was bent and so we tore off the heads send them off to have them put new valves and etc etc.. We put the car back together for them and now the car runs fine. They pick it up and about a few days later they brought it back due to a check engine. It threw the code:
16711 - Knock sensor 1-G61 Signal too low. (p0327)
now we replaced both knock sensors and when they came and got the car... the check engine light came back one showing the same code. We cleared it out and the next day it came back on showing the same code Again! So now we don't have a clue why that code keeps coming up because we replaced both sensors with a new one. Any clue why the code keeps popping back up?
Passat (B5) :: Getting Error Code P3081 - Coolant Temp Sensor?
P3081. What the hell is this code. I think it is a coolant temp. sensor issue.
View 3 RepliesPassat (B5) :: P0171 Engine Code - Mass Airflow Sensor Failed?
I've been getting this error code recently ("Fuel Trim,Bank1 System too Lean"). I have a Scanguage, which let me get the error code, and I used it to reset the message - it came back about a week later. I took it to a local repair shop after the second time, but as I'd already cleared the message, he couldn't do anything. It came back about a week later, and this time I took the vehicle in as soon as the yellow light showed up (without connecting the Scanguage).
The mechanic said that he found both P0171 and P0172, and that the problem was a loose vacuum hose AND a failing Mass Airlow Sensor. They reattached the hose and cleaned the sensor, but said that the latter fix may not last - the light came back on two days later. I took it in again (this time, checking the codes, and found only P0171) and he said this confirms the problem with the sensor and he'll have to replace it ($280 for the part, plus labor, less a discount on the labor equivalent to the labor he put in to clean the sensor.)
Passat (B6) :: Knock Sensor Code After Valve Carbon Scrubbing Service
I have a '07 Passat Wagon 2.0T with 80K miles. I just had the carbon scrubbed off the valves (looked like black popcorn stuck in there!) and now I'm getting a "P0327 Knock Sensor 1" light. The motor seems to run just fine (actually much better now without the carbon build-up). I'll clear the code but it will show up again the next day.
What could cause the code? Could it be related to the recent scrubbing (fully removed and replaced the valve cover in the process), perhaps a chunk of carbon floating around in the tubes somewhere? I want to go back to the guys that performed the service but I want to have a good idea of what could be the problem and the fix before I get there.
Passat (B5) :: 2002 - CEL Code For Bank 1 Sensor 2 Heater Circuit Fault
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 RepliesPassat (B5) :: Check Engine Light On / Code 16486 - Mass Air Flow Sensor Circuit Low Input
I cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 RepliesCorolla / Matrix 2009-13 :: 2010 Does Code P0037 Is For Bank 1 Sensor 2 Oxygen Sensor?
I have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
Ford 6.7L Power Stroke Diesel :: 2015 F550 - CEL Code Oxygen Sensor Performance Bank One Sensor One
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesFord Super Duty (1999-2016) :: Code P2195 (Bank 1 Sensor 1 O2 Sensor Stuck Lean)
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 Replies